Misplaced Pages

#989010

52-562: The Armstrong Siddeley Sapphire is a British turbojet engine that was produced by Armstrong Siddeley in the 1950s. It was the ultimate development of work that had started as the Metrovick F.2 in 1940, evolving into an advanced axial flow design with an annular combustion chamber that developed over 11,000 lbf (49 kN). It powered early versions of the Hawker Hunter and Handley Page Victor , and every Gloster Javelin . Production

104-416: A i r + m ˙ f ) V j − m ˙ a i r V {\displaystyle F_{N}=({\dot {m}}_{air}+{\dot {m}}_{f})V_{j}-{\dot {m}}_{air}V} where: If the speed of the jet is equal to sonic velocity the nozzle is said to be " choked ". If the nozzle is choked, the pressure at the nozzle exit plane

156-580: A gas turbine to power an aircraft was filed in 1921 by Frenchman Maxime Guillaume . His engine was to be an axial-flow turbojet, but was never constructed, as it would have required considerable advances over the state of the art in compressors. In 1928, British RAF College Cranwell cadet Frank Whittle formally submitted his ideas for a turbojet to his superiors. In October 1929 he developed his ideas further. On 16 January 1930 in England, Whittle submitted his first patent (granted in 1932). The patent showed

208-542: A landing field, lengthening flights. The increase in reliability that came with the turbojet enabled three- and two-engine designs, and more direct long-distance flights. High-temperature alloys were a reverse salient , a key technology that dragged progress on jet engines. Non-UK jet engines built in the 1930s and 1940s had to be overhauled every 10 or 20 hours due to creep failure and other types of damage to blades. British engines, however, utilised Nimonic alloys which allowed extended use without overhaul, engines such as

260-620: A low boost requirement were sometimes known as "wee-heat". Other low-boost reheats have included the "tailpipe augmentation"(TPA) on the F-86H (J73) with +10% at take-off and "Bristol Simplified Reheat"(BSR), with about 16% boost at take-off, tested on Derwent V, Orenda, Olympus and Orpheus engines. An Armstrong Siddeley Sapphire is on static display at the Midland Air Museum , Coventry Airport , Warwickshire . Very few Armstrong Siddeley Sapphire engines exist, other known examples are preserved at

312-454: A second generation SST engine using the 593 core were done more than three years before Concorde entered service. They evaluated bypass engines with bypass ratios between 0.1 and 1.0 to give improved take-off and cruising performance. Nevertheless, the 593 met all the requirements of the Concorde programme. Estimates made in 1964 for the Concorde design at Mach 2.2 showed the penalty in range for

364-411: A significant impact on commercial aviation . Aside from giving faster flight speeds turbojets had greater reliability than piston engines, with some models demonstrating dispatch reliability rating in excess of 99.9%. Pre-jet commercial aircraft were designed with as many as four engines in part because of concerns over in-flight failures. Overseas flight paths were plotted to keep planes within an hour of

416-405: A small helicopter engine compressor rotates around 50,000 RPM. Turbojets supply bleed air from the compressor to the aircraft for the operation of various sub-systems. Examples include the environmental control system , anti-icing , and fuel tank pressurization. The engine itself needs air at various pressures and flow rates to keep it running. This air comes from the compressor, and without it,

468-704: A turbine development of their own, the ASX , took over the MVSa.1, now renamed ASSa.1 . After a redesign it emerged as the ASSa.2 . In December 1949 the ASSa.2 completed an acceptance test at 7,380 lbf (32,800 N). Its competitor, the Avon RA.3 had a design thrust of 6,500 lbf (29,000 N) at that time. A number of companies expressed interest in the Sapphire, and it was considered as either

520-513: A turbojet application, where the output from the gas turbine is used in a propelling nozzle, raising the turbine temperature increases the jet velocity. At normal subsonic speeds this reduces the propulsive efficiency, giving an overall loss, as reflected by the higher fuel consumption, or SFC. However, for supersonic aircraft this can be beneficial, and is part of the reason why the Concorde employed turbojets. Turbojet systems are complex systems therefore to secure optimal function of such system, there

572-512: A turbojet engine is always subsonic, regardless of the speed of the aircraft itself. The intake has to supply air to the engine with an acceptably small variation in pressure (known as distortion) and having lost as little energy as possible on the way (known as pressure recovery). The ram pressure rise in the intake is the inlet's contribution to the propulsion system's overall pressure ratio and thermal efficiency . The intake gains prominence at high speeds when it generates more compression than

SECTION 10

#1732851671990

624-494: A turbojet is high enough at higher thrust settings to cause the nozzle to choke. If, however, a convergent-divergent de Laval nozzle is fitted, the divergent (increasing flow area) section allows the gases to reach supersonic velocity within the divergent section. Additional thrust is generated by the higher resulting exhaust velocity. Thrust was most commonly increased in turbojets with water/methanol injection or afterburning . Some engines used both methods. Liquid injection

676-480: A two-stage axial compressor feeding a single-sided centrifugal compressor . Practical axial compressors were made possible by ideas from A.A. Griffith in a seminal paper in 1926 ("An Aerodynamic Theory of Turbine Design"). Whittle later concentrated on the simpler centrifugal compressor only, for a variety of practical reasons. A Whittle engine was the first turbojet to run, the Power Jets WU , on 12 April 1937. It

728-584: Is a call for the newer models being developed to advance its control systems to implement the newest knowledge from the areas of automation, so increase its safety and effectiveness. Midland Air Museum The Midland Air Museum (MAM) is situated just outside the village of Baginton in Warwickshire , England , and is adjacent to Coventry Airport . The museum includes the Sir Frank Whittle Jet Heritage Centre (named after

780-413: Is a component of a turbojet used to divert air into the intake, in front of the accessory drive and to house the starter motor. An intake, or tube, is needed in front of the compressor to help direct the incoming air smoothly into the rotating compressor blades. Older engines had stationary vanes in front of the moving blades. These vanes also helped to direct the air onto the blades. The air flowing into

832-523: Is greater than atmospheric pressure, and extra terms must be added to the above equation to account for the pressure thrust. The rate of flow of fuel entering the engine is very small compared with the rate of flow of air. If the contribution of fuel to the nozzle gross thrust is ignored, the net thrust is: F N = m ˙ a i r ( V j − V ) {\displaystyle F_{N}={\dot {m}}_{air}(V_{j}-V)} The speed of

884-568: Is modelled approximately by the Brayton cycle . The efficiency of a gas turbine is increased by raising the overall pressure ratio, requiring higher-temperature compressor materials, and raising the turbine entry temperature, requiring better turbine materials and/or improved vane/blade cooling. It is also increased by reducing the losses as the flow progresses from the intake to the propelling nozzle. These losses are quantified by compressor and turbine efficiencies and ducting pressure losses. When used in

936-585: Is more commonly by use of a turboshaft engine, a development of the gas turbine engine where an additional turbine is used to drive a rotating output shaft. These are common in helicopters and hovercraft. Turbojets were widely used for early supersonic fighters , up to and including many third generation fighters , with the MiG-25 being the latest turbojet-powered fighter developed. As most fighters spend little time traveling supersonically, fourth-generation fighters (as well as some late third-generation fighters like

988-589: The Beryl , as well as the much larger F.9 Sapphire . (The names were chosen after a decision to use gemstones for future engine names). The Beryl eventually developed 4,000 lbf (18 kN) thrust, but the only project to select it, the Saunders-Roe SR.A/1 , was cancelled. The Ministry of Supply (MoS) designated the F.9 as the MVSa.1 . In 1948 Metrovick exited the jet engine industry. Armstrong Siddeley, who already had

1040-613: The F-111 and Hawker Siddeley Harrier ) and subsequent designs are powered by the more efficient low-bypass turbofans and use afterburners to raise exhaust speed for bursts of supersonic travel. Turbojets were used on Concorde and the longer-range versions of the Tu-144 which were required to spend a long period travelling supersonically. Turbojets are still common in medium range cruise missiles , due to their high exhaust speed, small frontal area, and relative simplicity. The first patent for using

1092-520: The FFA P-16 . The Sapphire compressor operated well, free from surging, over its complete RPM range without the need for variable inlet guide vanes (VIGV) or bleed. However, early compressor stages suffered from fatigue due to rotating stall at low RPM and various fixes, such as lacing wire, were incorporated. Curtiss-Wright introduced variable ramps on the Wright J65 at the entry to the compressor to prevent

SECTION 20

#1732851671990

1144-679: The Gloster Meteor , entered service in 1944, towards the end of World War II , the Me 262 in April and the Gloster Meteor in July. Only about 15 Meteor saw WW2 action but up to 1400 Me 262s were produced, with 300 entering combat, delivering the first ground attacks and air combat victories of jet planes. Air is drawn into the rotating compressor via the intake and is compressed to a higher pressure before entering

1196-571: The Heinkel HeS 3 ), or an axial compressor (as in the Junkers Jumo 004 ) which gave a smaller diameter, although longer, engine. By replacing the propeller used on piston engines with a high speed jet of exhaust, higher aircraft speeds were attainable. One of the last applications for a turbojet engine was Concorde which used the Olympus 593 engine. However, joint studies by Rolls-Royce and Snecma for

1248-673: The Jet Age Museum in Gloucester, England, and the Malta Aviation Museum at Ta' Qali . Data from Jane's. Related development Comparable engines Related lists Turbojet Turbojets have poor efficiency at low vehicle speeds, which limits their usefulness in vehicles other than aircraft. Turbojet engines have been used in isolated cases to power vehicles other than aircraft, typically for attempts on land speed records . Where vehicles are "turbine-powered", this

1300-515: The North American XB-70 Valkyrie , each feeding three engines with an intake airflow of about 800 pounds per second (360 kg/s). The turbine rotates the compressor at high speed, adding energy to the airflow while squeezing (compressing) it into a smaller space. Compressing the air increases its pressure and temperature. The smaller the compressor, the faster it turns. The (large) GE90-115B fan rotates at about 2,500 RPM, while

1352-479: The Rolls-Royce Welland and Rolls-Royce Derwent , and by 1949 the de Havilland Goblin , being type tested for 500 hours without maintenance. It was not until the 1950s that superalloy technology allowed other countries to produce economically practical engines. Early German turbojets had severe limitations on the amount of running they could do due to the lack of suitable high temperature materials for

1404-424: The Tu-144 , also used afterburners as does Scaled Composites White Knight , a carrier aircraft for the experimental SpaceShipOne suborbital spacecraft. Reheat was flight-trialled in 1944 on the W.2/700 engines in a Gloster Meteor I . The net thrust F N {\displaystyle F_{N}\;} of a turbojet is given by: F N = ( m ˙

1456-543: The Avon. The ASSa.6 , 8,300 lbf (37,000 N), was used on the Gloster Javelin FAW Mk.1 , Hawker Hunter F.Mk.2 and F.Mk.5, and the prototype Sud Ouest SO 4050 Vautour . The higher thrust ASSa.7 at 11,000 lbf (49 kN) was the first British engine to be rated above 10,000 lbf (44 kN) and it powered the Gloster Javelin FAW Mk.7 , Handley Page Victor B.Mk.1 and a prototype Swiss fighter-bomber,

1508-464: The aircraft decreases the efficiency of the engine because it has been compressed, but then does not contribute to producing thrust. Compressor types used in turbojets were typically axial or centrifugal. Early turbojet compressors had low pressure ratios up to about 5:1. Aerodynamic improvements including splitting the compressor into two separately rotating parts, incorporating variable blade angles for entry guide vanes and stators, and bleeding air from

1560-472: The blades causing catastrophic engine failures and loss of the aircraft. "Centre-line closure" also caused a Sapphire failure on a Victor B.1. An afterburner with limited boost was required for the Javelin's ASSa.7, making it the ASSa.7LR . 12% boost was required at high altitudes to regain the bomber intercept performance that had been lost carrying the new de Havilland Firestreak missiles. Afterburners with

1612-410: The combustion chamber. Fuel is mixed with the compressed air and burns in the combustor. The combustion products leave the combustor and expand through the turbine where power is extracted to drive the compressor. The turbine exit gases still contain considerable energy that is converted in the propelling nozzle to a high speed jet. The first turbojets, used either a centrifugal compressor (as in

Armstrong Siddeley Sapphire - Misplaced Pages Continue

1664-432: The combustor and pass through to the turbine in a continuous flowing process with no pressure build-up. Instead, a small pressure loss occurs in the combustor. The fuel-air mixture can only burn in slow-moving air, so an area of reverse flow is maintained by the fuel nozzles for the approximately stoichiometric burning in the primary zone. Further compressed air is introduced which completes the combustion process and reduces

1716-421: The compressor enabled later turbojets to have overall pressure ratios of 15:1 or more. After leaving the compressor, the air enters the combustion chamber. The burning process in the combustor is significantly different from that in a piston engine . In a piston engine, the burning gases are confined to a small volume, and as the fuel burns, the pressure increases. In a turbojet, the air and fuel mixture burn in

1768-401: The compressor is passed through these to keep the metal temperature within limits. The remaining stages do not need cooling. In the first stage, the turbine is largely an impulse turbine (similar to a pelton wheel ) and rotates because of the impact of the hot gas stream. Later stages are convergent ducts that accelerate the gas. Energy is transferred into the shaft through momentum exchange in

1820-521: The compressor stage. Well-known examples are the Concorde and Lockheed SR-71 Blackbird propulsion systems where the intake and engine contributions to the total compression were 63%/8% at Mach 2 and 54%/17% at Mach 3+. Intakes have ranged from "zero-length" on the Pratt & Whitney TF33 turbofan installation in the Lockheed C-141 Starlifter , to the twin 65 feet (20 m) long, intakes on

1872-475: The high-temperature materials used in their turbosuperchargers during World War II. Water injection was a common method used to increase thrust, usually during takeoff, in early turbojets that were thrust-limited by their allowable turbine entry temperature. The water increased thrust at the temperature limit, but prevented complete combustion, often leaving a very visible smoke trail. Allowable turbine entry temperatures have increased steadily over time both with

1924-441: The introduction of superior alloys and coatings, and with the introduction and progressive effectiveness of blade cooling designs. On early engines, the turbine temperature limit had to be monitored, and avoided, by the pilot, typically during starting and at maximum thrust settings. Automatic temperature limiting was introduced to reduce pilot workload and reduce the likelihood of turbine damage due to over-temperature. A nose bullet

1976-401: The jet V j {\displaystyle V_{j}\;} must exceed the true airspeed of the aircraft V {\displaystyle V\;} if there is to be a net forward thrust on the airframe. The speed V j {\displaystyle V_{j}\;} can be calculated thermodynamically based on adiabatic expansion . The operation of a turbojet

2028-399: The local aviation pioneer and inventor of the jet engine ), where many exhibits are on display in a large hangar . It also has a small hangar, and a fenced-off green area where many aircraft are on display in the open. The museum's two largest aircraft are an Avro Vulcan B.2 and an Armstrong Whitworth Argosy AW.650 (series 101) . The restored Avro Vulcan is a delta-winged aircraft that

2080-528: The main or backup powerplant for most British designs of the late '40s and early '50s. The ASSa.5 with 7,500 lbf (33,000 N) thrust was used only on the English Electric P.1A , prototype for the Lightning. A simple fixed-nozzle reheat was fitted to extend the performance boundary for stability and control testing from about Mach 1.1 to beyond Mach 1.5. Future versions of the Lightning were powered by

2132-402: The opposite way to energy transfer in the compressor. The power developed by the turbine drives the compressor and accessories, like fuel, oil, and hydraulic pumps that are driven by the accessory gearbox. After the turbine, the gases expand through the exhaust nozzle producing a high velocity jet. In a convergent nozzle, the ducting narrows progressively to a throat. The nozzle pressure ratio on

Armstrong Siddeley Sapphire - Misplaced Pages Continue

2184-486: The stalling and blade excitation. Armstrong-Siddeley tested a similar solution on the Sapphire but incorporated blade changes instead to reduce the blade response to the stalling. Caygill states that one of the most serious problems encountered throughout the life of the Gloster Javelin was caused by "centre-line closure" on the Sapphire engine. Flying through thick cloud could cause the compressor case to shrink and rub

2236-468: The supersonic airliner, in terms of miles per gallon, compared to subsonic airliners at Mach 0.85 (Boeing 707, DC-8) was relatively small. This is because the large increase in drag is largely compensated by an increase in powerplant efficiency (the engine efficiency is increased by the ram pressure rise which adds to the compressor pressure rise, the higher aircraft speed approaches the exhaust jet speed increasing propulsive efficiency). Turbojet engines had

2288-446: The temperature of the combustion products to a level which the turbine can accept. Less than 25% of the air is typically used for combustion, as an overall lean mixture is required to keep within the turbine temperature limits. Hot gases leaving the combustor expand through the turbine. Typical materials for turbines include inconel and Nimonic . The hottest turbine vanes and blades in an engine have internal cooling passages. Air from

2340-535: The thrust from a turbojet engine. It was flown by test pilot Erich Warsitz . The Gloster E.28/39 , (also referred to as the "Gloster Whittle", "Gloster Pioneer", or "Gloster G.40") made the first British jet-engined flight in 1941. It was designed to test the Whittle jet engine in flight, and led to the development of the Gloster Meteor. The first two operational turbojet aircraft, the Messerschmitt Me 262 and then

2392-412: The turbines would overheat, the lubricating oil would leak from the bearing cavities, the rotor thrust bearings would skid or be overloaded, and ice would form on the nose cone. The air from the compressor, called secondary air, is used for turbine cooling, bearing cavity sealing, anti-icing, and ensuring that the rotor axial load on its thrust bearing will not wear it out prematurely. Supplying bleed air to

2444-464: The turbines. British engines such as the Rolls-Royce Welland used better materials giving improved durability. The Welland was type-certified for 80 hours initially, later extended to 150 hours between overhauls, as a result of an extended 500-hour run being achieved in tests. General Electric in the United States was in a good position to enter the jet engine business due to its experience with

2496-623: Was also started under licence in the United States by Wright Aeronautical as the J65 , powering a number of US designs. The Sapphire's primary competitor was the Rolls-Royce Avon . Design evolution of the Sapphire started at Metropolitan-Vickers (Metrovick) in 1943 as an offshoot of the F.2 project. With the F.2 reaching flight quality at about 1,600 lbf (7,100 N), Metrovick turned to producing larger designs, both an enlarged F.2 known as

2548-424: Was liquid-fuelled. Whittle's team experienced near-panic during the first start attempts when the engine accelerated out of control to a relatively high speed despite the fuel supply being cut off. It was subsequently found that fuel had leaked into the combustion chamber during pre-start motoring checks and accumulated in pools, so the engine would not stop accelerating until all the leaked fuel had burned off. Whittle

2600-706: Was originally part of the V bomber force and could be equipped with nuclear missiles as part of Britain's role in NATO 's nuclear deterrent force during the Cold War . It is on display near the museum's car park, together with an Avro Blue Steel missile , an early design format of such a nuclear missile, and a Boulton Paul BP.111A , an experimental delta-winged aircraft of the 1950s. The museum also has an English Electric Canberra PR.3 , two English Electric Lightnings (the RAF's fastest ever interceptor), two Gloster Meteors (one on loan from

2652-629: Was tested on the Power Jets W.1 in 1941 initially using ammonia before changing to water and then water-methanol. A system to trial the technique in the Gloster E.28/39 was devised but never fitted. An afterburner or "reheat jetpipe" is a combustion chamber added to reheat the turbine exhaust gases. The fuel consumption is very high, typically four times that of the main engine. Afterburners are used almost exclusively on supersonic aircraft , most being military aircraft. Two supersonic airliners, Concorde and

SECTION 50

#1732851671990

2704-479: Was unable to interest the government in his invention, and development continued at a slow pace. In Germany, Hans von Ohain patented a similar engine in 1935. His design, an axial-flow engine, as opposed to Whittle's centrifugal flow engine, was eventually adopted by most manufacturers by the 1950s. On 27 August 1939 the Heinkel He 178 , powered by von Ohain's design, became the world's first aircraft to fly using

#989010