A jet is a stream of fluid that is projected into a surrounding medium, usually from some kind of a nozzle , aperture or orifice . Jets can travel long distances without dissipating .
51-601: The RD-107 and its sibling, the RD-108 , are a type of rocket engine used on the R-7 rocket family . RD-107 engines are used in each booster and the RD-108 is used in the central core. The engines have four main combustion chambers (each a with nozzle ) and either two (RD-107) or four (RD-108) vernier chambers. The engines were first developed in the mid-1950s to launch the R-7 Semyorka ,
102-533: A gas-generator cycle . As was typical by all the descendants of the V-2 rocket technology, the turbine is driven by steam generated by catalytic decomposition of H₂O₂ . The steam generator uses solid F-30-P-G catalyst. These are based on a variable sized pellet covered in an aqueous solution of potassium permanganate and sodium . Each engine uses four fixed main combustion chambers. The RD-107 has an additional two vernier combustion chambers that can thrust vector in
153-433: A propelling nozzle . The fluid is usually a gas created by high pressure (150-to-4,350-pound-per-square-inch (10 to 300 bar)) combustion of solid or liquid propellants , consisting of fuel and oxidiser components, within a combustion chamber . As the gases expand through the nozzle, they are accelerated to very high ( supersonic ) speed, and the reaction to this pushes the engine in the opposite direction. Combustion
204-409: A vacuum to propel spacecraft and ballistic missiles . Compared to other types of jet engine, rocket engines are the lightest and have the highest thrust, but are the least propellant-efficient (they have the lowest specific impulse ). The ideal exhaust is hydrogen , the lightest of all elements, but chemical rockets produce a mix of heavier species, reducing the exhaust velocity. Here, "rocket"
255-470: A higher velocity compared to air. Expansion in the rocket nozzle then further multiplies the speed, typically between 1.5 and 2 times, giving a highly collimated hypersonic exhaust jet. The speed increase of a rocket nozzle is mostly determined by its area expansion ratio—the ratio of the area of the exit to the area of the throat, but detailed properties of the gas are also important. Larger ratio nozzles are more massive but are able to extract more heat from
306-439: A hot gas jet for propulsion. Alternatively, a chemically inert reaction mass can be heated by a high-energy power source through a heat exchanger in lieu of a combustion chamber. Solid rocket propellants are prepared in a mixture of fuel and oxidising components called grain , and the propellant storage casing effectively becomes the combustion chamber. Liquid-fuelled rockets force separate fuel and oxidiser components into
357-529: A maximum limit determined only by the mechanical strength of the engine. In practice, the degree to which rockets can be throttled varies greatly, but most rockets can be throttled by a factor of 2 without great difficulty; the typical limitation is combustion stability, as for example, injectors need a minimum pressure to avoid triggering damaging oscillations (chugging or combustion instabilities); but injectors can be optimised and tested for wider ranges. Jet (fluid) Jet fluid has higher speed compared to
408-424: A number called L ∗ {\displaystyle L^{*}} , the characteristic length : where: L* is typically in the range of 64–152 centimetres (25–60 in). The temperatures and pressures typically reached in a rocket combustion chamber in order to achieve practical thermal efficiency are extreme compared to a non-afterburning airbreathing jet engine . No atmospheric nitrogen
459-514: A preliminary design completed in 1993. These engines incorporate a new injector head design to increase specific impulse . The first launch of a Progress cargo spacecraft using a launch vehicle equipped with these engines took place in May 2001. The first human spaceflight launch utilizing these engines took place in October 2002. Rocket engine A rocket engine uses stored rocket propellants as
510-567: A single plane to supply attitude control. The RD-108 has four verniers to supply full vector control to the Blok-A stage. The single-axle turbopump unit includes the steam driven turbine, an oxidizer pump, a fuel pump, and a nitrogen gas generator for tank pressurization. The RD-107 engines are used in each of the boosters of the Soyuz-2 rocket, and a single RD-108 is used in the Blok-A stage (the central 1st stage). One important innovation of this engine
561-432: A variety of design approaches including turbopumps or, in simpler engines, via sufficient tank pressure to advance fluid flow. Tank pressure may be maintained by several means, including a high-pressure helium pressurization system common to many large rocket engines or, in some newer rocket systems, by a bleed-off of high-pressure gas from the engine cycle to autogenously pressurize the propellant tanks For example,
SECTION 10
#1732858751143612-400: Is designed for, but exhaust speeds as high as ten times the speed of sound in air at sea level are not uncommon. About half of the rocket engine's thrust comes from the unbalanced pressures inside the combustion chamber, and the rest comes from the pressures acting against the inside of the nozzle (see diagram). As the gas expands ( adiabatically ) the pressure against the nozzle's walls forces
663-412: Is difficult to arrange in a lightweight fashion, although is routinely done with other forms of jet engines. In rocketry a lightweight compromise nozzle is generally used and some reduction in atmospheric performance occurs when used at other than the 'design altitude' or when throttled. To improve on this, various exotic nozzle designs such as the plug nozzle , stepped nozzles , the expanding nozzle and
714-408: Is either measured as a speed (the effective exhaust velocity v e {\displaystyle v_{e}} in metres/second or ft/s) or as a time (seconds). For example, if an engine producing 100 pounds of thrust runs for 320 seconds and burns 100 pounds of propellant, then the specific impulse is 320 seconds. The higher the specific impulse, the less propellant is required to provide
765-404: Is force divided by the rate of mass flow, this equation means that the specific impulse varies with altitude. Due to the specific impulse varying with pressure, a quantity that is easy to compare and calculate with is useful. Because rockets choke at the throat, and because the supersonic exhaust prevents external pressure influences travelling upstream, it turns out that the pressure at the exit
816-554: Is ideally exactly proportional to the propellant flow m ˙ {\displaystyle {\dot {m}}} , provided the mixture ratios and combustion efficiencies are maintained. It is thus quite usual to rearrange the above equation slightly: and so define the vacuum Isp to be: where: And hence: Rockets can be throttled by controlling the propellant combustion rate m ˙ {\displaystyle {\dot {m}}} (usually measured in kg/s or lb/s). In liquid and hybrid rockets,
867-423: Is important that the maximum pressures possible be created on the walls of the chamber and nozzle by a specific amount of propellant; as this is the source of the thrust. This can be achieved by all of: Since all of these things minimise the mass of the propellant used, and since pressure is proportional to the mass of propellant present to be accelerated as it pushes on the engine, and since from Newton's third law
918-504: Is most frequently used for practical rockets, as the laws of thermodynamics (specifically Carnot's theorem ) dictate that high temperatures and pressures are desirable for the best thermal efficiency . Nuclear thermal rockets are capable of higher efficiencies, but currently have environmental problems which preclude their routine use in the Earth's atmosphere and cislunar space . For model rocketry , an available alternative to combustion
969-406: Is no 'ram drag' to deduct from the gross thrust. Consequently, the net thrust of a rocket motor is equal to the gross thrust (apart from static back pressure). The m ˙ v e − o p t {\displaystyle {\dot {m}}\;v_{e-opt}\,} term represents the momentum thrust, which remains constant at a given throttle setting, whereas
1020-409: Is permitted to escape through an opening (the "throat"), and then through a diverging expansion section. When sufficient pressure is provided to the nozzle (about 2.5–3 times ambient pressure), the nozzle chokes and a supersonic jet is formed, dramatically accelerating the gas, converting most of the thermal energy into kinetic energy. Exhaust speeds vary, depending on the expansion ratio the nozzle
1071-443: Is present to dilute and cool the combustion, so the propellant mixture can reach true stoichiometric ratios. This, in combination with the high pressures, means that the rate of heat conduction through the walls is very high. In order for fuel and oxidiser to flow into the chamber, the pressure of the propellants entering the combustion chamber must exceed the pressure inside the combustion chamber itself. This may be accomplished by
SECTION 20
#17328587511431122-427: Is termed exhaust velocity , and after allowance is made for factors that can reduce it, the effective exhaust velocity is one of the most important parameters of a rocket engine (although weight, cost, ease of manufacture etc. are usually also very important). For aerodynamic reasons the flow goes sonic (" chokes ") at the narrowest part of the nozzle, the 'throat'. Since the speed of sound in gases increases with
1173-443: Is the water rocket pressurized by compressed air, carbon dioxide , nitrogen , or any other readily available, inert gas. Rocket propellant is mass that is stored, usually in some form of tank, or within the combustion chamber itself, prior to being ejected from a rocket engine in the form of a fluid jet to produce thrust. Chemical rocket propellants are the most commonly used. These undergo exothermic chemical reactions producing
1224-423: Is used as an abbreviation for "rocket engine". Thermal rockets use an inert propellant, heated by electricity ( electrothermal propulsion ) or a nuclear reactor ( nuclear thermal rocket ). Chemical rockets are powered by exothermic reduction-oxidation chemical reactions of the propellant: Rocket engines produce thrust by the expulsion of an exhaust fluid that has been accelerated to high speed through
1275-402: The A e ( p e − p a m b ) {\displaystyle A_{e}(p_{e}-p_{amb})\,} term represents the pressure thrust term. At full throttle, the net thrust of a rocket motor improves slightly with increasing altitude, because as atmospheric pressure decreases with altitude, the pressure thrust term increases. At the surface of
1326-404: The aerospike have been proposed, each providing some way to adapt to changing ambient air pressure and each allowing the gas to expand further against the nozzle, giving extra thrust at higher altitudes. When exhausting into a sufficiently low ambient pressure (vacuum) several issues arise. One is the sheer weight of the nozzle—beyond a certain point, for a particular vehicle, the extra weight of
1377-654: The reaction mass for forming a high-speed propulsive jet of fluid, usually high-temperature gas. Rocket engines are reaction engines , producing thrust by ejecting mass rearward, in accordance with Newton's third law . Most rocket engines use the combustion of reactive chemicals to supply the necessary energy, but non-combusting forms such as cold gas thrusters and nuclear thermal rockets also exist. Vehicles propelled by rocket engines are commonly used by ballistic missiles (they normally use solid fuel ) and rockets . Rocket vehicles carry their own oxidiser , unlike most combustion engines, so rocket engines can be used in
1428-401: The water tap , the showerhead , and from spray cans . In agriculture, they play a role in irrigation and in the application of crop protection products . In the field of medicine, you can find liquid jets for example in injection procedures or inhalers . Industry uses liquid jets for waterjet cutting , for coating materials or in cooling towers . Atomized liquid jets are essential for
1479-603: The Earth the pressure thrust may be reduced by up to 30%, depending on the engine design. This reduction drops roughly exponentially to zero with increasing altitude. Maximum efficiency for a rocket engine is achieved by maximising the momentum contribution of the equation without incurring penalties from over expanding the exhaust. This occurs when p e = p a m b {\displaystyle p_{e}=p_{amb}} . Since ambient pressure changes with altitude, most rocket engines spend very little time operating at peak efficiency. Since specific impulse
1530-465: The atmosphere, and while permitting the use of low pressure and hence lightweight tanks and structure. Rockets can be further optimised to even more extreme performance along one or more of these axes at the expense of the others. The most important metric for the efficiency of a rocket engine is impulse per unit of propellant , this is called specific impulse (usually written I s p {\displaystyle I_{sp}} ). This
1581-407: The axis of the engine, a side force may be imparted to the engine. This side force may change over time and result in control problems with the launch vehicle. Advanced altitude-compensating designs, such as the aerospike or plug nozzle , attempt to minimize performance losses by adjusting to varying expansion ratio caused by changing altitude. For a rocket engine to be propellant efficient, it
RD-107 - Misplaced Pages Continue
1632-424: The combustion chamber, where they mix and burn. Hybrid rocket engines use a combination of solid and liquid or gaseous propellants. Both liquid and hybrid rockets use injectors to introduce the propellant into the chamber. These are often an array of simple jets – holes through which the propellant escapes under pressure; but sometimes may be more complex spray nozzles. When two or more propellants are injected,
1683-462: The combustion gases, increasing the exhaust velocity. Vehicles typically require the overall thrust to change direction over the length of the burn. A number of different ways to achieve this have been flown: Rocket technology can combine very high thrust ( meganewtons ), very high exhaust speeds (around 10 times the speed of sound in air at sea level) and very high thrust/weight ratios (>100) simultaneously as well as being able to operate outside
1734-452: The desired impulse. The specific impulse that can be achieved is primarily a function of the propellant mix (and ultimately would limit the specific impulse), but practical limits on chamber pressures and the nozzle expansion ratios reduce the performance that can be achieved. Below is an approximate equation for calculating the net thrust of a rocket engine: Since, unlike a jet engine, a conventional rocket motor lacks an air intake, there
1785-571: The efficiency of internal combustion engines . But they also play a crucial role in research, for example in the study of proteins , phase transitions , extreme states of matter , laser plasmas , High harmonic generation , and also in particle physics experiments. Also some animals, notably cephalopods , move by jet propulsion . Gas jets are found in rocket engines and jet engines . Microscopic liquid jets have been studied for their potential application in noninvasive transdermal drug delivery . This fluid dynamics –related article
1836-671: The first intercontinental ballistic missile . The R-7 was later adapted into space launch vehicles and the engines have been improved over several generations. The most recent versions are the RD-107A and RD-108A engines are used to launch the Soyuz-2 , which is in active service as of 2024. The RD-107 was designed under the direction of Valentin Glushko at the Experimental Design Bureau (OKB-456) between 1954 and 1957. It uses liquid oxygen and kerosene as propellants operating in
1887-411: The jet may be either below or above ambient, and equilibrium between the two is not reached at all altitudes (see diagram). For optimal performance, the pressure of the gas at the end of the nozzle should just equal the ambient pressure: if the exhaust's pressure is lower than the ambient pressure, then the vehicle will be slowed by the difference in pressure between the top of the engine and the exit; on
1938-536: The jets usually deliberately cause the propellants to collide as this breaks up the flow into smaller droplets that burn more easily. For chemical rockets the combustion chamber is typically cylindrical, and flame holders , used to hold a part of the combustion in a slower-flowing portion of the combustion chamber, are not needed. The dimensions of the cylinder are such that the propellant is able to combust thoroughly; different rocket propellants require different combustion chamber sizes for this to occur. This leads to
1989-539: The manufacture of RD-107 and RD-108 engines. The branch was led by Y.D. Solovjev until 1960, then by R.I. Zelenev until 1975, then by A.F. Udalov until 1978, and is currently led by A.A. Ganin. Modifications to the RD-107 design have led to production of several distinct versions of the engine: Similar modifications have led to several distinct versions of the RD-108: Work on the 14D21 and 14D22 engines started in 1986, with
2040-644: The mass imbalance. The mixture ratio control system was developed to ensure the simultaneous consumption of propellant mass among the four R-7 boosters. The RD-107 and RD-108 engines are produced at the JSC Kuznetsov plant in Samara, Russia , under the supervision of the Privolzhskiy branch of NPO Energomash , also known as the Volga branch. The Privolzhsky branch was organized as a branch of OKB-456 in 1958, specifically for
2091-417: The nozzle outweighs any performance gained. Secondly, as the exhaust gases adiabatically expand within the nozzle they cool, and eventually some of the chemicals can freeze, producing 'snow' within the jet. This causes instabilities in the jet and must be avoided. On a de Laval nozzle , exhaust gas flow detachment will occur in a grossly over-expanded nozzle. As the detachment point will not be uniform around
RD-107 - Misplaced Pages Continue
2142-495: The nozzle. As exit pressure varies from the ambient (atmospheric) pressure, a choked nozzle is said to be In practice, perfect expansion is only achievable with a variable–exit-area nozzle (since ambient pressure decreases as altitude increases), and is not possible above a certain altitude as ambient pressure approaches zero. If the nozzle is not perfectly expanded, then loss of efficiency occurs. Grossly over-expanded nozzles lose less efficiency, but can cause mechanical problems with
2193-403: The nozzle. Fixed-area nozzles become progressively more under-expanded as they gain altitude. Almost all de Laval nozzles will be momentarily grossly over-expanded during startup in an atmosphere. Nozzle efficiency is affected by operation in the atmosphere because atmospheric pressure changes with altitude; but due to the supersonic speeds of the gas exiting from a rocket engine, the pressure of
2244-431: The other hand, if the exhaust's pressure is higher, then exhaust pressure that could have been converted into thrust is not converted, and energy is wasted. To maintain this ideal of equality between the exhaust's exit pressure and the ambient pressure, the diameter of the nozzle would need to increase with altitude, giving the pressure a longer nozzle to act on (and reducing the exit pressure and temperature). This increase
2295-407: The pressure that acts on the engine also reciprocally acts on the propellant, it turns out that for any given engine, the speed that the propellant leaves the chamber is unaffected by the chamber pressure (although the thrust is proportional). However, speed is significantly affected by all three of the above factors and the exhaust speed is an excellent measure of the engine propellant efficiency. This
2346-409: The propellant flow entering the chamber is controlled using valves, in solid rockets it is controlled by changing the area of propellant that is burning and this can be designed into the propellant grain (and hence cannot be controlled in real-time). Rockets can usually be throttled down to an exit pressure of about one-third of ambient pressure (often limited by flow separation in nozzles) and up to
2397-425: The rocket engine in one direction while accelerating the gas in the other. The most commonly used nozzle is the de Laval nozzle , a fixed geometry nozzle with a high expansion-ratio. The large bell- or cone-shaped nozzle extension beyond the throat gives the rocket engine its characteristic shape. The exit static pressure of the exhaust jet depends on the chamber pressure and the ratio of exit to throat area of
2448-508: The self-pressurization gas system of the SpaceX Starship is a critical part of SpaceX strategy to reduce launch vehicle fluids from five in their legacy Falcon 9 vehicle family to just two in Starship, eliminating not only the helium tank pressurant but all hypergolic propellants as well as nitrogen for cold-gas reaction-control thrusters . The hot gas produced in the combustion chamber
2499-412: The square root of temperature, the use of hot exhaust gas greatly improves performance. By comparison, at room temperature the speed of sound in air is about 340 m/s while the speed of sound in the hot gas of a rocket engine can be over 1700 m/s; much of this performance is due to the higher temperature, but additionally rocket propellants are chosen to be of low molecular mass, and this also gives
2550-468: The surrounding fluid medium. In the case that the surrounding medium is assumed to be made up of the same fluid as the jet, and this fluid has viscosity , some of the surrounding fluid is carried along with the jet in a process called entrainment . Some animals, notably cephalopods , move by jet propulsion , as do rocket engines and jet engines . Liquid jets are used in many different areas. In everyday life, you can find them for instance coming from
2601-449: Was the capability to use variable mixture ratio between fuel and oxidizer. The natural variations in manufacturing between each engine meant that without an active propellant consumption control, each booster could deplete oxygen and fuel at a different rate. This might result in as much as tens of tonnes of unused propellant near the end of the burn. It would generate enormous stress on the structure and cause difficulties in steering due to
SECTION 50
#1732858751143#142857