Misplaced Pages

#409590

57-407: The 1903 Pope-Toledo was a four-wheel, front-engined, two-seater open car. It was powered by a straight 3 cylinder 182 cubic inch (2983 cc) engine with the then unusual feature of a detachable cylinder head . Valve operation was mechanical and the engine speed was governed at 600 RPM . Drive was through a 3-speed gearbox with chains to each rear wheel. The chassis was mainly wood with

114-415: A power-valve system . The valves are normally in or around the exhaust ports. They work in one of two ways; either they alter the exhaust port by closing off the top part of the port, which alters port timing, such as Rotax R.A.V.E, Yamaha YPVS, Honda RC-Valve, Kawasaki K.I.P.S., Cagiva C.T.S., or Suzuki AETC systems, or by altering the volume of the exhaust, which changes the resonant frequency of

171-421: A rotary valve is that it enables the two-stroke engine's intake timing to be asymmetrical, which is not possible with piston-port type engines. The piston-port type engine's intake timing opens and closes before and after top dead center at the same crank angle, making it symmetrical, whereas the rotary valve allows the opening to begin and close earlier. Rotary valve engines can be tailored to deliver power over

228-403: A 180 degree crankshaft, where the outer pistons rise and fall together and inner cylinder is offset from them by 180 degrees. This results in three power strokes evenly-spaced at 180 degrees each, and then no power strokes during the final 180 degrees of crankshaft rotation. The 2020 Triumph Tiger 900 motorcycle uses a "T-Plane" crankshaft where the crankshaft throws are at 90 intervals, such that

285-691: A 543 cc (33 cu in) four-stroke engine, which was introduced in the Alto and Fronte models. The Subaru EF engine is a 4-stroke petrol engine which was introduced in 1984 and used in the Justy and the Sumo (the export version of the Sambar). The straight-three versions of the Ford EcoBoost engine – a turbocharged 1.0-litre petrol engine – was introduced in the 2012 Ford Focus. It uses an unbalanced flywheel to shift

342-421: A DKW design that proved reasonably successful employing loop charging. The original SAAB 92 had a two-cylinder engine of comparatively low efficiency. At cruising speed, reflected-wave, exhaust-port blocking occurred at too low a frequency. Using the asymmetrical three-port exhaust manifold employed in the identical DKW engine improved fuel economy. The 750-cc standard engine produced 36 to 42 hp, depending on

399-448: A crossflow engine) is always best and support is good. In some engines, the small end is offset to reduce thrust in the intended rotational direction and the forward face of the piston has been made thinner and lighter to compensate, but when running backward, this weaker forward face suffers increased mechanical stress it was not designed to resist. This can be avoided by the use of crossheads and also using thrust bearings to isolate

456-465: A patent in 1880 in Germany. The first truly practical two-stroke engine is attributed to Yorkshireman Alfred Angas Scott , who started producing twin-cylinder water-cooled motorcycles in 1908. Two-stroke gasoline engines with electrical spark ignition are particularly useful in lightweight or portable applications such as chainsaws and motorcycles. However, when weight and size are not an issue,

513-449: A scavenging function. The units run in pairs, with the lower half of one piston charging an adjacent combustion chamber. The upper section of the piston still relies on total-loss lubrication, but the other engine parts are sump lubricated with cleanliness and reliability benefits. The mass of the piston is only about 20% more than a loop-scavenged engine's piston because skirt thicknesses can be less. Many modern two-stroke engines employ

570-658: A similar system. Traditional flywheel magnetos (using contact-breaker points, but no external coil) worked equally well in reverse because the cam controlling the points is symmetrical, breaking contact before top dead center equally well whether running forward or backward. Reed-valve engines run backward just as well as piston-controlled porting, though rotary valve engines have asymmetrical inlet timing and do not run very well. Serious disadvantages exist for running many engines backward under load for any length of time, and some of these reasons are general, applying equally to both two-stroke and four-stroke engines. This disadvantage

627-512: A steel sub-frame carrying the main mechanical components. The car had a wheelbase of 7 feet 5 inches (2.26 m) and a track of 4 feet 8 inches (1.42 m). It was entered in the first Vanderbilt Cup (1904), but lost its steering and hit a tree. The 1904 model was a larger touring car . Equipped with a rear entrance tonneau body, it could seat 5 passengers and sold for $ 3,500, equivalent to $ 118,689 in 2023. The vertically mounted water-cooled straight-4 , situated at

SECTION 10

#1732859017410

684-588: A straight-twin engine. Four-stroke straight-three engines have been used in road bikes and racing bikes by several companies. From 1985–1995, the BMW K75 was produced with a straight-three engine (based on the straight-four engine from the BMW K100). British company Triumph is particularly renowned for a transversely-mounted straight-three engine. Variants have been used in their Speed Triple , Trident , Sprint , and Tiger series. In addition Triumph makes

741-518: A turbocharger. Crankcase-compression two-stroke engines, such as common small gasoline-powered engines, are lubricated by a petroil mixture in a total-loss system . Oil is mixed in with their petrol fuel beforehand, in a fuel-to-oil ratio of around 32:1. This oil then forms emissions, either by being burned in the engine or as droplets in the exhaust, historically resulting in more exhaust emissions, particularly hydrocarbons, than four-stroke engines of comparable power output. The combined opening time of

798-400: A wider speed range or higher power over a narrower speed range than either a piston-port or reed-valve engine. Where a portion of the rotary valve is a portion of the crankcase itself, of particular importance, no wear should be allowed to take place. In a cross-flow engine, the transfer and exhaust ports are on opposite sides of the cylinder, and a deflector on the top of the piston directs

855-421: Is a type of internal combustion engine that completes a power cycle with two strokes of the piston (one up and one down movement) in one revolution of the crankshaft. (A four-stroke engine requires four strokes of the piston to complete a power cycle, in two crankshaft revolutions.) In a two-stroke engine, the end of the combustion stroke and the beginning of the compression stroke happen simultaneously, with

912-413: Is accepted in most cases where cost, weight, and size are major considerations. The problem comes about because in "forward" running, the major thrust face of the piston is on the back face of the cylinder, which in a two-stroke particularly, is the coolest and best-lubricated part. The forward face of the piston in a trunk engine is less well-suited to be the major thrust face, since it covers and uncovers

969-422: Is attributed to Scottish engineer Dugald Clerk , who patented his design in 1881. However, unlike most later two-stroke engines, his had a separate charging cylinder. The crankcase -scavenged engine, employing the area below the piston as a charging pump, is generally credited to Englishman Joseph Day . On 31 December 1879, German inventor Karl Benz produced a two-stroke gas engine, for which he received

1026-590: Is being phased out. Honda , for instance, ceased selling two-stroke off-road motorcycles in the United States in 2007, after abandoning road-going models considerably earlier. Due to their high power-to-weight ratio and ability to be used in any orientation, two-stroke engines are common in handheld outdoor power tools including leaf blowers , chainsaws , and string trimmers . Two-stroke diesel engines are found mostly in large industrial and marine applications, as well as some trucks and heavy machinery. Although

1083-565: Is common in on-road, off-road, and stationary two-stroke engines ( Detroit Diesel ), certain small marine two-stroke engines ( Gray Marine Motor Company , which adapted the Detroit Diesel Series 71 for marine use ), certain railroad two-stroke diesel locomotives ( Electro-Motive Diesel ) and large marine two-stroke main propulsion engines ( Wärtsilä ). Ported types are represented by the opposed piston design in which two pistons are in each cylinder, working in opposite directions such as

1140-432: Is that the two-stroke's crankcase is sealed and forms part of the induction process in gasoline and hot-bulb engines . Diesel two-strokes often add a Roots blower or piston pump for scavenging . The reed valve is a simple but highly effective form of check valve commonly fitted in the intake tract of the piston-controlled port. It allows asymmetric intake of the fuel charge, improving power and economy, while widening

1197-733: Is the Fairbanks-Morse 32E14 low-speed diesel engine. The straight-three layout is common for diesel tractor engines, such as the Perkins AD3.152 . This engine was used in the Massey Ferguson 35 and Fordson Dextra tractors, as well as for marine and stationary applications. The Hewland AE75 is a 750 cc two-stroke aircraft engine that was produced in the mid-1980s. It was an inverted three-cylinder design with liquid-cooling that produced 75 bhp (56 kW). Two-stroke engine A two-stroke (or two-stroke cycle ) engine

SECTION 20

#1732859017410

1254-515: Is typically used by straight-three engines, since this results in an evenly spaced firing interval . Another benefit of this configuration is perfect primary balance and secondary balance , however an end-to-end rocking couple is induced because there is no symmetry in the piston velocities about the middle piston. A balance shaft is sometimes used to reduce the vibrations caused by the rocking couple. Other crankshaft angles have been used occasionally. The 1976–1981 Laverda Jota motorcycle used

1311-409: Is under every circumstance more efficient than cross-flow scavenging. In a uniflow engine, the mixture, or "charge air" in the case of a diesel, enters at one end of the cylinder controlled by the piston and the exhaust exits at the other end controlled by an exhaust valve or piston. The scavenging gas-flow is, therefore, in one direction only, hence the name uniflow. The design using exhaust valve(s)

1368-458: The Junkers Jumo 205 and Napier Deltic . The once-popular split-single design falls into this class, being effectively a folded uniflow. With advanced-angle exhaust timing, uniflow engines can be supercharged with a crankshaft-driven blower, either piston or Roots-type. The piston of this engine is "top-hat"-shaped; the upper section forms the regular cylinder, and the lower section performs

1425-569: The Rocket III model, various variants of which have held the record for motorcycle with the largest engine displacement. In 2019 , the Moto2 class in the MotoGP World Championship switched to using Triumph 765 cc (46.7 cu in) triple engines. Two-stroke designs are less common in straight-three engines than four-stroke designs, however several were produced by Japanese manufacturers in

1482-506: The expansion chamber , such as the Suzuki SAEC and Honda V-TACS system. The result is an engine with better low-speed power without sacrificing high-speed power. However, as power valves are in the hot gas flow, they need regular maintenance to perform well. Direct injection has considerable advantages in two-stroke engines. In carburetted two-strokes, a major problem is a portion of the fuel/air mixture going directly out, unburned, through

1539-473: The oil reservoir does not depend on gravity. A number of mainstream automobile manufacturers have used two-stroke engines in the past, including the Swedish Saab , German manufacturers DKW , Auto-Union , VEB Sachsenring Automobilwerke Zwickau , VEB Automobilwerk Eisenach , and VEB Fahrzeug- und Jagdwaffenwerk , and Polish manufacturers FSO and FSM . The Japanese manufacturers Suzuki and Subaru did

1596-528: The 1960s due in no small way to the increased power afforded by loop scavenging. An additional benefit of loop scavenging was the piston could be made nearly flat or slightly domed, which allowed the piston to be appreciably lighter and stronger, and consequently to tolerate higher engine speeds. The "flat top" piston also has better thermal properties and is less prone to uneven heating, expansion, piston seizures, dimensional changes, and compression losses. SAAB built 750- and 850-cc three-cylinder engines based on

1653-407: The 1960s, especially for motorcycles, but for smaller or slower engines using direct injection, the deflector piston can still be an acceptable approach. This method of scavenging uses carefully shaped and positioned transfer ports to direct the flow of fresh mixture toward the combustion chamber as it enters the cylinder. The fuel/air mixture strikes the cylinder head , then follows the curvature of

1710-448: The German inventor of an early form in the mid-1920s, it became widely adopted in Germany country during the 1930s and spread further afield after World War II . Loop scavenging is the most common type of fuel/air mixture transfer used on modern two-stroke engines. Suzuki was one of the first manufacturers outside of Europe to adopt loop-scavenged, two-stroke engines. This operational feature

1767-527: The Pope Motor Car Company receivers sold the factory to Overland . Straight-3 A straight-three engine (also called an inline-triple or inline-three ) is a three-cylinder piston engine where cylinders are arranged in a line along a common crankshaft. Less common than straight-four engines , straight-three engines have nonetheless been used in various motorcycles, cars and agricultural machinery. A crankshaft angle of 120 degrees

Pope-Toledo - Misplaced Pages Continue

1824-423: The bore diameter for reasonable piston ring life. Beyond this, the piston rings bulge into the exhaust port and wear quickly. A maximum 70% of bore width is possible in racing engines, where rings are changed every few races. Intake duration is between 120 and 160°. Transfer port time is set at a minimum of 26°. The strong, low-pressure pulse of a racing two-stroke expansion chamber can drop the pressure to -7 psi when

1881-696: The car was protested by runners up as being a special factory-owned "ringer". This protest was rejected by the Columbus Driving Park officials. In 1908, Bobby Sheldon brought a 1906 Pope-Toledo down the Yukon to Fairbanks, the first car brought to Alaska. By 1907 the company models included limousines and seven seat cars. In 1909 the company was taken over by Richard D. Apperson of the American National Bank of Lynchburg, Virginia (and no relation to Apperson of Kokomo ). The Apperson deal failed and

1938-459: The combustion chamber, and then is deflected downward. This not only prevents the fuel/air mixture from traveling directly out the exhaust port, but also creates a swirling turbulence which improves combustion efficiency , power, and economy. Usually, a piston deflector is not required, so this approach has a distinct advantage over the cross-flow scheme (above). Often referred to as "Schnuerle" (or "Schnürle") loop scavenging after Adolf Schnürle,

1995-453: The crankshaft commonly spins in the same axis and direction as do the wheels i.e. "forward". Some of the considerations discussed here apply to four-stroke engines (which cannot reverse their direction of rotation without considerable modification), almost all of which spin forward, too. It is also useful to note that the "front" and "back" faces of the piston are - respectively - the exhaust port and intake port sides of it, and are not to do with

2052-415: The cycle's potential for high thermodynamic efficiency makes it ideal for diesel compression ignition engines operating in large, weight-insensitive applications, such as marine propulsion , railway locomotives , and electricity generation . In a two-stroke engine, the exhaust gases transfer less heat to the cooling system than a four-stroke, which means more energy to drive the piston, and if present,

2109-400: The engine from end loads. Large two-stroke ship diesels are sometimes made to be reversible. Like four-stroke ship engines (some of which are also reversible), they use mechanically operated valves, so require additional camshaft mechanisms. These engines use crossheads to eliminate sidethrust on the piston and isolate the under-piston space from the crankcase. On top of other considerations,

2166-415: The exhaust port in the cylinder, the hottest part of the engine, where piston lubrication is at its most marginal. The front face of the piston is also more vulnerable since the exhaust port, the largest in the engine, is in the front wall of the cylinder. Piston skirts and rings risk being extruded into this port, so having them pressing hardest on the opposite wall (where there are only the transfer ports in

2223-409: The exhaust port, and direct injection effectively eliminates this problem. Two systems are in use: low-pressure air-assisted injection and high-pressure injection. Since the fuel does not pass through the crankcase, a separate source of lubrication is needed. For the purpose of this discussion, it is convenient to think in motorcycle terms, where the exhaust pipe faces into the cooling air stream, and

2280-413: The fresh intake charge into the upper part of the cylinder, pushing the residual exhaust gas down the other side of the deflector and out the exhaust port. The deflector increases the piston's weight and exposed surface area, and the fact that it makes piston cooling and achieving an effective combustion chamber shape more difficult is why this design has been largely superseded by uniflow scavenging after

2337-525: The front of the car, produced 24 hp (17.9 kW ). A 3-speed sliding transmission was fitted. The channel steel-framed car weighed 2350 lb (1066 kg ). This modern Système Panhard car had spark and throttle levers on steering wheel, a novelty at the time. In 1905, a Pope-Toledo owned by C. Edward Born was driven 828.5 miles before a crowd of 15,000 to win the world's first 24-hour endurance race in Columbus, Ohio . Piloted by brothers George and Charles Soules,

Pope-Toledo - Misplaced Pages Continue

2394-412: The inherent three-cylinder imbalance to the horizontal plane where it is more easily managed by engine mounts, and so remove the need to use balance shafts. In 2016, cylinder deactivation was added, claimed to be a world first for three-cylinder engines. The advantages of a straight-three engine for motorcycles are that it has a shorter length than an inline-four engine and produces less vibration than

2451-741: The intake and exhaust (or scavenging ) functions occurring at the same time. Two-stroke engines often have a higher power-to-weight ratio than a four-stroke engine, since their power stroke occurs twice as often. Two-stroke engines can also have fewer moving parts , and thus be cheaper to manufacture and weigh less. In countries and regions with stringent emissions regulation, two-stroke engines have been phased out in automotive and motorcycle uses. In regions where regulations are less stringent, small displacement two-stroke engines remain popular in mopeds and motorcycles. They are also used in power tools such as chainsaws and leaf blowers . The first commercial two-stroke engine involving cylinder compression

2508-443: The intake and exhaust ports in some two-stroke designs can also allow some amount of unburned fuel vapors to exit in the exhaust stream. The high combustion temperatures of small, air-cooled engines may also produce NO x emissions. Two-stroke gasoline engines are preferred when mechanical simplicity, light weight, and high power-to-weight ratio are design priorities. By mixing oil with fuel, they can operate in any orientation as

2565-676: The introduction of Saab's 750 cc (46 cu in) two-stroke engine, which was also used in the Saab 95 , Saab 96 and Saab Sonett until 1968 after which it was replaced by the Ford Taunus V4 engine . The Wartburg cars (manufactured in East Germany) and FSO Syrena (manufactured in Poland) also used straight-three engines. The 1967 Suzuki Fronte 360 uses a 256 cc (16 cu in) two-stroke engine. In 1980, Suzuki began production of

2622-426: The late 1960s through to 1980s. The Kawasaki triple engine was produced from 1968 to 1980 and was used in various road bikes and racing bikes. Most versions were air-cooled, however several were water-cooled. Similarly, the 1972–1980 Suzuki GT series engines were used for both road bike and racing bikes, and were available in both air-cooled and water-cooled versions. An example of an agricultural application

2679-469: The model year. The Monte Carlo Rally variant, 750-cc (with a filled crankshaft for higher base compression), generated 65 hp. An 850-cc version was available in the 1966 SAAB Sport (a standard trim model in comparison to the deluxe trim of the Monte Carlo). Base compression comprises a portion of the overall compression ratio of a two-stroke engine. Work published at SAE in 2012 points that loop scavenging

2736-399: The oil pump of a modern two-stroke may not work in reverse, in which case the engine suffers oil starvation within a short time. Running a motorcycle engine backward is relatively easy to initiate, and in rare cases, can be triggered by a back-fire. It is not advisable. Model airplane engines with reed valves can be mounted in either tractor or pusher configuration without needing to change

2793-483: The other - the inlet pipe having passage to the crankcase only when the two cutouts coincide. The crankshaft itself may form one of the members, as in most glow-plug model engines. In another version, the crank disc is arranged to be a close-clearance fit in the crankcase, and is provided with a cutout that lines up with an inlet passage in the crankcase wall at the appropriate time, as in Vespa motor scooters. The advantage of

2850-434: The piston covering and uncovering the ports as it moves up and down in the cylinder. In the 1970s, Yamaha worked out some basic principles for this system. They found that, in general, widening an exhaust port increases the power by the same amount as raising the port, but the power band does not narrow as it does when the port is raised. However, a mechanical limit exists to the width of a single exhaust port, at about 62% of

2907-440: The piston is at bottom dead center, and the transfer ports nearly wide open. One of the reasons for high fuel consumption in two-strokes is that some of the incoming pressurized fuel-air mixture is forced across the top of the piston, where it has a cooling action, and straight out the exhaust pipe. An expansion chamber with a strong reverse pulse stops this outgoing flow. A fundamental difference from typical four-stroke engines

SECTION 50

#1732859017410

2964-550: The power band. Such valves are widely used in motorcycle, ATV, and marine outboard engines. The intake pathway is opened and closed by a rotating member. A familiar type sometimes seen on small motorcycles is a slotted disk attached to the crankshaft , which covers and uncovers an opening in the end of the crankcase, allowing charge to enter during one portion of the cycle (called a disc valve). Another form of rotary inlet valve used on two-stroke engines employs two cylindrical members with suitable cutouts arranged to rotate one within

3021-466: The principles remain the same, the mechanical details of various two-stroke engines differ depending on the type. The design types vary according to the method of introducing the charge to the cylinder, the method of scavenging the cylinder (exchanging burnt exhaust for fresh mixture) and the method of exhausting the cylinder. Piston port is the simplest of the designs and the most common in small two-stroke engines. All functions are controlled solely by

3078-806: The same in the 1970s. Production of two-stroke cars ended in the 1980s in the West, due to increasingly stringent regulation of air pollution . Eastern Bloc countries continued until around 1991, with the Trabant and Wartburg in East Germany. Two-stroke engines are still found in a variety of small propulsion applications, such as outboard motors , small on- and off-road motorcycles , mopeds , motor scooters , motorized bicycles , tuk-tuks , snowmobiles , go-karts , RC cars , ultralight and model airplanes. Particularly in developed countries, pollution regulations have meant that their use for many of these applications

3135-473: The throws for cylinders 1 and 3 are separated by 180 degrees (therefore the three throws together forming a "T" shape when viewed from the end). Among the first cars to use a straight-three engine is the 1953–1955 DKW F91 , powered by a 900 cc (55 cu in) two-stroke engine , although this was predated by the 3 cylinder 15hp Rolls Royce produced in 1905 and a number of other cars of this era also used 3 cylinder engines. The 1956–1960 Saab 93 saw

3192-511: The top or bottom of the piston. Regular gasoline two-stroke engines can run backward for short periods and under light load with little problem, and this has been used to provide a reversing facility in microcars , such as the Messerschmitt KR200 , that lacked reverse gearing. Where the vehicle has electric starting, the motor is turned off and restarted backward by turning the key in the opposite direction. Two-stroke golf carts have used

3249-530: Was used in conjunction with the expansion chamber exhaust developed by German motorcycle manufacturer, MZ, and Walter Kaaden. Loop scavenging, disc valves, and expansion chambers worked in a highly coordinated way to significantly increase the power output of two-stroke engines, particularly from the Japanese manufacturers Suzuki, Yamaha, and Kawasaki. Suzuki and Yamaha enjoyed success in Grand Prix motorcycle racing in

#409590