Misplaced Pages

#910089

76-466: An overhead line consists of one or more wires (or rails , particularly in tunnels) situated over rail tracks , raised to a high electrical potential by connection to feeder stations at regularly spaced intervals along the track. The feeder stations are usually fed from a high-voltage electrical grid . Electric trains that collect their current from overhead lines use a device such as a pantograph , bow collector or trolley pole . It presses against

152-413: A block and tackle arrangement. Lines are divided into sections to limit the scope of an outage and to allow maintenance. To allow maintenance to the overhead line without having to turn off the entire system, the line is broken into electrically separated portions known as "sections". Sections often correspond with tension lengths. The transition from section to section is known as a "section break" and

228-419: A swing bridge . The catenary wire typically comprises messenger wire (also called catenary wire) and a contact wire where it meets the pantograph. The messenger wire is terminated at the portal, while the contact wire runs into the overhead conductor rail profile at the transition end section before it is terminated at the portal. There is a gap between the overhead conductor rail at the transition end section and

304-476: A "Backdoor" connection between different parts, resulting in, amongst other things, a section of the grid de-energised for maintenance being re-energised from the railway substation creating danger. For these reasons, Neutral sections are placed in the electrification between the sections fed from different points in a national grid, or different phases, or grids that are not synchronized. It is highly undesirable to connect unsynchronized grids. A simple section break

380-724: A commercial installation on a streetcar system in South Bend, Indiana, which opened on November 14, 1885, and on one in Montgomery, Alabama, in April 1886. However, within a few months, Van Depoele switched to the trolley-pole system for the Montgomery operation. Van Depoele and fellow inventor Frank J. Sprague were "working on similar ideas at about the same time", and Sprague employed trolley-pole current collection on an electric streetcar system he installed in Richmond, Virginia, in 1888, also improving

456-485: A detent, like that in an automotive shoulder safety belt , which "catches" the rope to prevent the trolley pole from flying upward if the pole is dewired. The similar looking retriever (see photo) adds a spring mechanism that yanks the pole downward if it should leave the wire, pulling it away from all overhead wire fittings. Catchers are commonly used on trams operating at lower speeds, as in a city, whilst retrievers are used on suburban and interurban lines to limit damage to

532-524: A few others worldwide retain use of trolley poles, even on new streetcars, in order to avoid the difficulty and expense of modifying long stretches of existing overhead wires to accept pantographs. However, the Toronto Transit Commission , with the impending replacement of its legacy CLRV and ALRV with new Flexity Outlook cars, converted its overhead power supply to be compatible with both trolley poles and pantographs on an interim basis, as

608-411: A fixed centre point, with the two half-tension lengths expanding and contracting with temperature. Most systems include a brake to stop the wires from unravelling completely if a wire breaks or tension is lost. German systems usually use a single large tensioning pulley (basically a ratchet mechanism) with a toothed rim, mounted on an arm hinged to the mast. Normally the downward pull of the weights and

684-596: A high risk of short circuits at switches and therefore tend to be impractical in use, especially when high voltages are used or when trains run through the points at high speed. Wire Too Many Requests If you report this error to the Wikimedia System Administrators, please include the details below. Request from 172.68.168.151 via cp1112 cp1112, Varnish XID 385927590 Upstream caches: cp1112 int Error: 429, Too Many Requests at Fri, 29 Nov 2024 05:34:56 GMT Trolley pole A trolley pole

760-484: A level crossing with the 1,200 V DC Uetliberg railway line ; at many places, trolleybus lines cross the tramway. In some cities, trolleybuses and trams shared a positive (feed) wire. In such cases, a normal trolleybus frog can be used. Alternatively, section breaks can be sited at the crossing point, so that the crossing is electrically dead. Many cities had trams and trolleybuses using trolley poles. They used insulated crossovers, which required tram drivers to put

836-568: A multiple unit passes over them. In the United Kingdom equipment similar to Automatic Warning System (AWS) is used, but with pairs of magnets placed outside the running rails (as opposed to the AWS magnets placed midway between the rails). Lineside signs on the approach to the neutral section warn the driver to shut off traction power and coast through the dead section. A neutral section or phase break consists of two insulated breaks back-to-back with

SECTION 10

#1732858495911

912-403: A pneumatic servo pantograph with only 3  g acceleration. An electrical circuit requires at least two conductors. Trams and railways use the overhead line as one side of the circuit and the steel rails as the other side of the circuit. For a trolleybus or a trolleytruck , no rails are available for the return current, as the vehicles use rubber tyres on the road surface. Trolleybuses use

988-427: A railway vehicle), a single trolley pole usually collects current from the overhead wire, and the steel rails on the tracks act as the electrical return . To reduce electrolytic corrosion of underground pipes and metallic structures, most tram lines are operated with the wire positive with respect to the rails. Trolleybuses , on the other hand, must use two trolley poles and dual overhead wires, one pole and wire for

1064-456: A reduction in arcing), and it dramatically reduced overhead wire wear. Many systems began converting to the sliding trolley shoe in the 1920s; Milwaukee, Wisconsin converted its large system in the late 1920s. Philadelphia did not convert its trolley wheels on its remaining streetcars until 1978. Although a streetcar with a trolley wheel may evoke an antique look, the trolley shoe is modern and more practical as well as economical. A trolley pole

1140-415: A return path for the current through their wheels, and must instead use a pair of overhead wires to provide both the current and its return path. To achieve good high-speed current collection, it is necessary to keep the contact wire geometry within defined limits. This is usually achieved by supporting the contact wire from a second wire known as the messenger wire or catenary . This wire approximates

1216-414: A rigid overhead wire in their tunnels, while using normal overhead wires in their above ground sections. In a movable bridge that uses a rigid overhead rail, there is a need to transition from the catenary wire system into an overhead conductor rail at the bridge portal (the last traction current pylon before the movable bridge). For example, the power supply can be done through a catenary wire system near

1292-461: A second parallel overhead line for the return, and two trolley poles , one contacting each overhead wire. ( Pantographs are generally incompatible with parallel overhead lines.) The circuit is completed by using both wires. Parallel overhead wires are also used on the rare railways with three-phase AC railway electrification . In the Soviet Union the following types of wires/cables were used. For

1368-467: A short section of line that belongs to neither grid. Some systems increase the level of safety by the midpoint of the neutral section being earthed. The presence of the earthed section in the middle is to ensure that should the transducer controlled apparatus fail, and the driver also fail to shut off power, the energy in the arc struck by the pantograph as it passes to the neutral section is conducted to earth, operating substation circuit breakers, rather than

1444-530: A simpler alternative for moveable overhead power rails. Electric trains coast across the gaps. To prevent arcing, power must be switched off before reaching the gap and usually the pantograph would be lowered. Given limited clearance such as in tunnels , the overhead wire may be replaced by a rigid overhead rail. An early example was in the tunnels of the Baltimore Belt Line , where a Π section bar (fabricated from three strips of iron and mounted on wood)

1520-469: A tilted position into the horizontal position, connecting the conductor rails at the transition end section and the bridge together to supply power. Short overhead conductor rails are installed at tram stops as for the Combino Supra . Trams draw their power from a single overhead wire at about 500 to 750  V DC. Trolleybuses draw from two overhead wires at a similar voltage, and at least one of

1596-689: A tramway. The tramway operated on 600–700 V DC and the railway on 15 kV AC . In the Swiss village of Oberentfelden , the Menziken–Aarau–Schöftland line operating at 750 V DC crosses the SBB line at 15 kV AC; there used to be a similar crossing between the two lines at Suhr but this was replaced by an underpass in 2010. Some crossings between tramway/light rail and railways are extant in Germany. In Zürich , Switzerland, VBZ trolleybus line 32 has

SECTION 20

#1732858495911

1672-570: A witch astride— The string you see to her leg is tied. In 1947, composer Samuel Barber wrote the now-classic orchestral and vocal piece Knoxville: Summer of 1915 , based on the childhood reminiscences of James Agee . Partway through the composition, the singer refers to a noisy passing streetcar, with its overhead trolley pole and sparks: A streetcar raising into iron moan; stopping; belling and starting, stertorous; rousing and raising again its iron increasing moan and swimming its gold windows and straw seats on past and past and past,

1748-472: Is a matter of raising one and lowering the other. Since the operator could raise the pole at one end whilst the conductor lowered the other, this saved time and was much easier for the conductor. Care had to be taken to raise the downed pole first, to eliminate the damage caused by arcing between the pole and wire. In the US, the dual-pole system was the most common arrangement on double-ended vehicles. However, pushing of

1824-595: Is a tapered cylindrical pole of wood or metal , used to transfer electricity from a "live" (electrified) overhead wire to the control and the electric traction motors of a tram or trolley bus . It is a type of current collector . The use of overhead wire in a system of current collection is reputed to be the 1880 invention of Frank J. Sprague , but the first working trolley pole was developed and demonstrated by Charles Van Depoele , in autumn 1885. An early development of an experimental tramway in Toronto , Ontario ,

1900-422: Is briefly in contact with both wires). In normal service, the two sections are electrically connected; depending on the system this might be an isolator, fixed contact or a Booster Transformer. The isolator allows the current to the section to be interrupted for maintenance. On overhead wires designed for trolley poles, this is done by having a neutral section between the wires, requiring an insulator. The driver of

1976-595: Is given to Charles Joseph Van Depoele , a Belgian engineer who moved to the United States in 1869. Van Depoele made the first public demonstration of the spring-loaded device on a temporary streetcar line installed at the Toronto Industrial Exhibition (now the CNE) in autumn 1885. Depoele's first trolley pole was "crude" and not very reliable, and he reverted to using the troller system of current collection for

2052-417: Is in use, standard sizes for contact wire are 100 and 150 mm. The catenary wire is made of copper or copper alloys of 70, 120 or 150 mm. The smaller cross sections are made of 19 strands, whereas the bigger has 37 strands. Two standard configurations for main lines consist of two contact wires of 100 mm and one or two catenary wires of 120 mm, totaling 320 or 440 mm. Only one contact wire

2128-414: Is insufficient to guard against this as the pantograph briefly connects both sections. In countries such as France, South Africa, Australia and the United Kingdom, a pair of permanent magnets beside the rails at either side of the neutral section operate a bogie-mounted transducer on the train which causes a large electrical circuit-breaker to open and close when the locomotive or the pantograph vehicle of

2204-497: Is not attached to the overhead wire. The pole sits atop a sprung base on the roof of the vehicle, with springs providing the pressure to keep the trolley wheel or shoe in contact with the wire. If the pole is made of wood, a cable brings the electric current down to the vehicle. A metal pole may use such a cable, or may itself be electrically "live", requiring the base to be insulated from the vehicle body. On systems with double-ended tram cars capable of running in both directions,

2280-445: Is often used for side tracks. In the UK and EU countries , the contact wire is typically made from copper alloyed with other metals. Sizes include cross-sectional areas of 80, 100, 107, 120, and 150 mm. Common materials include normal and high strength copper, copper-silver, copper-cadmium, copper-magnesium, and copper-tin, with each being identifiable by distinct identification grooves along

2356-476: Is problematic for longer modern streetcars that draw more electricity than older streetcars. In Toronto, the trolley pole shoe contains a carbon insert to provide electrical contact with the overhead wire and to lower the shoe to clear overhead wire hangers. Carbon inserts wear out and must be periodically replaced. The trolley shoe inserts on Toronto's modern Flexity Outlook streetcars quickly wear out in rainy conditions, lasting as little as eight hours instead of

Overhead line - Misplaced Pages Continue

2432-421: Is set up so that the vehicle's pantograph is in continuous contact with one wire or the other. For bow collectors and pantographs, this is done by having two contact wires run side by side over the length between 2 or 4 wire supports. A new one drops down and the old one rises up, allowing the pantograph to smoothly transfer from one to the other. The two wires do not touch (although the bow collector or pantograph

2508-981: Is used only on the Gornergrat Railway and Jungfrau Railway in Switzerland, the Petit train de la Rhune in France, and the Corcovado Rack Railway in Brazil. Until 1976, it was widely used in Italy. On these railways, the two conductors are used for two different phases of the three-phase AC, while the rail was used for the third phase. The neutral was not used. Some three-phase AC railways used three overhead wires. These were an experimental railway line of Siemens in Berlin-Lichtenberg in 1898 (length 1.8 kilometres (1.1 mi)),

2584-570: The Daugavpils, Latvia system , and Rio de Janeiro 's Santa Teresa Tramway . The MBTA system of Boston still uses trolley poles with the PCC streetcars it uses to serve the Ashmont–Mattapan High Speed Line . Trams or light rail cars equipped with pantographs normally cannot operate on lines with overhead wiring designed for trolley-pole collection. For this reason, these systems and

2660-463: The tram or trolleybus must temporarily reduce the power draw before the trolley pole passes through, to prevent arc damage to the insulator. Pantograph-equipped locomotives must not run through a section break when one side is de-energized. The locomotive would become trapped, but as it passes the section break the pantograph briefly shorts the two catenary lines. If the opposite line is de-energized, this voltage transient may trip supply breakers. If

2736-498: The trolley pole wheel and pole designs. Known as the Richmond Union Passenger Railway , this 12-mile (19 km) system was the first large-scale trolley line in the world, opening to great fanfare on February 12, 1888. The grooved trolley wheel was used on many large city systems through the 1940s and 1950s; it was generally used on systems with "old" style round cross sectional overhead wire. The trolley wheel

2812-491: The 1500 V DC overhead of the railway and the 650 V DC of the trams, called a Tram Square. Several such crossings have been grade separated in recent years as part of the Level Crossing Removal Project . Athens has two crossings of tram and trolleybus wires, at Vas. Amalias Avenue and Vas. Olgas Avenue, and at Ardittou Street and Athanasiou Diakou Street. They use the above-mentioned solution. In Rome , at

2888-562: The CLRVs and ALRVs use only trolley poles while the Flexity fleet is equipped for both trolley poles and pantographs. Large portions of San Francisco's surface network are also set up to handle both trolley pole and pantograph operation in order to allow for compatibility both with Muni's current fleet of light rail vehicles (pantograph only), as well as Muni's historic streetcar fleet (trolley pole only). Upon their introduction, trolley poles and

2964-517: The Hell's Gate Bridge boundary between Amtrak and Metro North 's electrifications) that would never be in-phase. Since a dead section is always dead, no special signal aspect was developed to warn drivers of its presence, and a metal sign with "DS" in drilled-hole letters was hung from the catenary supports. Occasionally gaps may be present in the overhead lines, when switching from one voltage to another or to provide clearance for ships at moveable bridges, as

3040-556: The arc either bridging the insulators into a section made dead for maintenance, a section fed from a different phase, or setting up a Backdoor connection between different parts of the country's national grid. On the Pennsylvania Railroad , phase breaks were indicated by a position light signal face with all eight radial positions with lenses and no center light. When the phase break was active (the catenary sections out of phase), all lights were lit. The position light signal aspect

3116-611: The contact wire, cold drawn solid copper was used to ensure good conductivity . The wire is not round but has grooves at the sides to allow the hangers to attach to it. Sizes were (in cross-sectional area) 85, 100, or 150 mm. To make the wire stronger, 0.04% tin might be added. The wire must resist the heat generated by arcing and thus such wires should never be spliced by thermal means. The messenger (or catenary) wire needs to be both strong and have good conductivity. They used multi-strand wires (or cables) with 19 strands in each cable (or wire). Copper, aluminum, and/or steel were used for

Overhead line - Misplaced Pages Continue

3192-476: The controller into neutral and coast through. Trolleybus drivers had to either lift off the accelerator or switch to auxiliary power. In Melbourne , Victoria, tram drivers put the controller into neutral and coast through section insulators, indicated by insulator markings between the rails. Melbourne has several remaining level crossings between electrified suburban railways and tram lines. They have mechanical switching arrangements (changeover switch) to switch

3268-526: The crossing between Viale Regina Margherita and Via Nomentana, tram and trolleybus lines cross: tram on Viale Regina Margherita and trolleybus on Via Nomentana. The crossing is orthogonal, therefore the typical arrangement was not available. In Milan , most tram lines cross its circular trolleybus line once or twice. Trolleybus and tram wires run parallel in streets such as viale Stelvio, viale Umbria and viale Tibaldi. Some railways used two or three overhead lines, usually to carry three-phase current. This

3344-793: The expected one to two days for shorter older streetcars. The extra current draw shortens the life of the carbon insert. A worn-out carbon insert would damage the overhead wire, stopping streetcar service. Apart from heritage streetcar lines, very few tram/streetcar systems worldwide continue to use trolley poles on vehicles used in normal service. Among the largest exceptions are the streetcar systems of New Orleans, Louisiana ; Toronto, Ontario ; Philadelphia (the "Subway-Surface" lines and Route 15 ); Riga, Latvia (however, new Škoda trams in Riga have pantographs); Kolkata (formerly Calcutta), India ; and Alexandria, Egypt . Smaller systems still using trolley poles for regular service include Hong Kong Tramways ,

3420-451: The line is under maintenance, an injury may occur as the catenary is suddenly energized. Even if the catenary is properly grounded to protect the personnel, the arc generated across the pantograph can damage the pantograph, the catenary insulator or both. Sometimes on a larger electrified railway, tramway or trolleybus system, it is necessary to power different areas of track from different power grids, without guaranteeing synchronisation of

3496-478: The military railway between Marienfelde and Zossen between 1901 and 1904 (length 23.4 kilometres (14.5 mi)) and an 800-metre (2,600 ft)-long section of a coal railway near Cologne between 1940 and 1949. On DC systems, bipolar overhead lines were sometimes used to avoid galvanic corrosion of metallic parts near the railway, such as on the Chemin de fer de la Mure . All systems with multiple overhead lines have

3572-409: The natural path of a wire strung between two points, a catenary curve , thus the use of "catenary" to describe this wire or sometimes the whole system. This wire is attached to the contact wire at regular intervals by vertical wires known as "droppers" or "drop wires". It is supported regularly at structures, by a pulley , link or clamp . The whole system is then subjected to mechanical tension . As

3648-403: The need to manually turn the trolley pole when changing direction (although this disadvantage can be overcome to some extent through the use of trolley reversers). The use of pantographs (or bow collectors) exclusively also eliminates the need for wire frogs (switches in the overhead wiring) to make sure the pole goes in the correct direction at junctions. The trolley pole with a shoe at its tip

3724-466: The new electrical technology they represented were fascinating to writers, with their lightning -like sparks and power. In January 1889, Boston introduced its first electric streetcars, which became so popular and noteworthy that poet Oliver Wendell Holmes composed a verse about the new trolley pole technology, and the sparking contact shoe at its apex: Since then on many a car you'll see A broomstick as plain as plain can be; On every stick there's

3800-438: The overhead at speed. On some older systems, the poles were raised and lowered using a long pole with a metal hook. Where available, these may have been made of bamboo due to its length, natural straightness and strength, combined with its relative light weight and the fact that it is an insulator. Trolleybuses usually carried one with the vehicle, for use in the event of dewirement, but tram systems usually had them placed along

3876-402: The overhead conductor rail that runs across the entire span of the swing bridge. The gap is required for the swing bridge to be opened and closed. To connect the conductor rails together when the bridge is closed, there is another conductor rail section called "rotary overlap" that is equipped with a motor. When the bridge is fully closed, the motor of the rotary overlap is operated to turn it from

SECTION 50

#1732858495911

3952-479: The overhead line is limited due to the change in the height of the weights as the overhead line expands and contracts with temperature changes. This movement is proportional to the distance between anchors. Tension length has a maximum. For most 25 kV OHL equipment in the UK, the maximum tension length is 1,970 m (6,460 ft). An additional issue with AT equipment is that, if balance weights are attached to both ends,

4028-455: The pantograph as the train travels around the curve. The movement of the contact wire across the head of the pantograph is called the "sweep". The zigzagging of the overhead line is not required for trolley poles. For tramways , a contact wire without a messenger wire is used. Depot areas tend to have only a single wire and are known as "simple equipment" or "trolley wire". When overhead line systems were first conceived, good current collection

4104-457: The pantograph causes mechanical oscillations in the wire. The waves must travel faster than the train to avoid producing standing waves , which could break the wire. Tensioning the line makes waves travel faster, and also reduces sag from gravity. For medium and high speeds, the wires are generally tensioned by weights or occasionally by hydraulic tensioners. Either method is known as "auto-tensioning" (AT) or "constant tension" and ensures that

4180-411: The pantograph moves along under the contact wire, the carbon insert on top of the pantograph becomes worn with time. On straight track, the contact wire is zigzagged slightly to the left and right of the centre from each support to the next so that the insert wears evenly, thus preventing any notches. On curves, the "straight" wire between the supports causes the contact point to cross over the surface of

4256-424: The phases. Long lines may be connected to the country's national grid at various points and different phases. (Sometimes the sections are powered with different voltages or frequencies.) The grids may be synchronised on a normal basis, but events may interrupt synchronisation. This is not a problem for DC systems. AC systems have a particular safety implication in that the railway electrification system would act as

4332-495: The pole (called "back-poling" in the US or "spear-poling" in Australia), was quite common where the trams were moving at slow speeds, such as at wye terminals (also known as reversers) and whilst backing into the sheds. Trolley poles are usually raised and lowered manually by a rope from the back of the vehicle. The rope feeds into a spring reel mechanism, called a "trolley catcher" or "trolley retriever". The trolley catcher contains

4408-605: The positive "live" current, the other for the negative or neutral return . The tramway system in Havana , Cuba , also utilized the dual-wire system, as did the Cincinnati, Ohio streetcar system . All trolleybuses use trolley poles, and thus trolley poles remain in use worldwide, wherever trolleybuses are in operation (some 315 cities as of 2011 ), and several manufacturers continue to make them, including Kiepe , Škoda and Lekov . However, on most railway vehicles using overhead wire,

4484-519: The reactive upward pull of the tensioned wires lift the pulley so its teeth are well clear of a stop on the mast. The pulley can turn freely while the weights move up or down as the wires contract or expand. If tension is lost the pulley falls back toward the mast, and one of its teeth jams against the stop. This stops further rotation, limits the damage, and keeps the undamaged part of the wire intact until it can be repaired. Other systems use various braking mechanisms, usually with multiple smaller pulleys in

4560-410: The route at locations where the trolley pole would need reversing. The poles used on trolleybuses are typically longer than those used on trams, to allow the bus to take fuller advantage of its not being restricted to a fixed path in the street (the rails), by giving a degree of lateral steerability, enabling the trolleybus to board passengers at curbside. When used on a tram or trolley car (i.e.

4636-420: The stiffness of the spring for ease of maintenance. For low speeds and in tunnels where temperatures are constant, fixed termination (FT) equipment may be used, with the wires terminated directly on structures at each end of the overhead line. The tension is generally about 10 kN (2,200 lbf). This type of equipment sags in hot conditions and is taut in cold conditions. With AT, the continuous length of

SECTION 60

#1732858495911

4712-487: The strands. All 19 strands could be made of the same metal or a mix of metals based on the required properties. For example, steel wires were used for strength, while aluminium or copper wires were used for conductivity. Another type looked like it had all copper wires but inside each wire was a steel core for strength. The steel strands were galvanized but for better corrosion protection they could be coated with an anti-corrosion substance. In Slovenia , where 3 kV system

4788-514: The tension is virtually independent of temperature. Tensions are typically between 9 and 20  kN (2,000 and 4,500  lbf ) per wire. Where weights are used, they slide up and down on a rod or tube attached to the mast, to prevent them from swaying. Recently, spring tensioners have started to be used. These devices contain a torsional spring with a cam arrangement to ensure a constant applied tension (instead of varying proportionally with extension). Some devices also include mechanisms for adjusting

4864-465: The tram wire. The tram's pantograph bridges the gap between the different conductors, providing it with a continuous pickup. Where the tram wire crosses, the trolleybus wires are protected by an inverted trough of insulating material extending 20 or 30 mm (0.79 or 1.18 in) below. Until 1946, a level crossing in Stockholm , Sweden connected the railway south of Stockholm Central Station and

4940-405: The trolley pole has given way to the bow collector or, later, the pantograph , a folding metal device that presses a wide contact pan against the overhead wire. While more complex than the trolley pole, the pantograph has the advantage of being almost free from dewiring, being more stable at high speed, and being easier to raise and lower automatically. Also, on double-ended trams , they eliminate

5016-424: The trolley pole must always be pulled behind the car and not pushed, or "dewiring" is very likely, which can cause damage to the overhead wires. At terminus points, the conductor must turn the trolley pole around to face the correct direction, pulling it off the wire either with a rope or a pole and walking it around to the other end. In some cases, two trolley poles are provided, one for each direction: in this case it

5092-444: The trolleybus wires must be insulated from tram wires. This is usually done by the trolleybus wires running continuously through the crossing, with the tram conductors a few centimetres lower. Close to the junction on each side, the tram wire turns into a solid bar running parallel to the trolleybus wires for about half a metre. Another bar similarly angled at its ends is hung between the trolleybus wires, electrically connected above to

5168-639: The underside of the lowest overhead wire, the contact wire. Current collectors are electrically conductive and allow current to flow through to the train or tram and back to the feeder station through the steel wheels on one or both running rails. Non-electric locomotives (such as diesels ) may pass along these tracks without affecting the overhead line, although there may be difficulties with overhead clearance . Alternative electrical power transmission schemes for trains include third rail , ground-level power supply , batteries and electromagnetic induction . Vehicles like buses that have rubber tyres cannot provide

5244-405: The upper lobe of the contact wire. These grooves vary in number and location on the arc of the upper section. Copper is chosen for its excellent conductivity, with other metals added to increase tensile strength. The choice of material is chosen based on the needs of the particular system, balancing the need for conductivity and tensile strength. Catenary wires are kept in mechanical tension because

5320-496: The whole tension length is free to move along the track. To avoid this a midpoint anchor (MPA), close to the centre of the tension length, restricts movement of the messenger/catenary wire by anchoring it; the contact wire and its suspension hangers can move only within the constraints of the MPA. MPAs are sometimes fixed to low bridges, or otherwise anchored to vertical catenary poles or portal catenary supports. A tension length can be seen as

5396-474: Was built in 1883, having been developed by John Joseph Wright , brother of swindler Whitaker Wright . While Wright may have assisted in the installation of electric railways at the Canadian National Exhibition (CNE), and may even have used a pole system, there is no evidence about this. Likewise, Wright never filed or was issued a patent. Credit for development of the first working trolley pole

5472-715: Was originally devised by the Pennsylvania Railroad and was continued by Amtrak and adopted by Metro North . Metal signs were hung from the catenary supports with the letters "PB" created by a pattern of drilled holes. A special category of phase break was developed in America, primarily by the Pennsylvania Railroad. Since its traction power network was centrally supplied and only segmented by abnormal conditions, normal phase breaks were generally not active. Phase breaks that were always activated were known as "Dead Sections": they were often used to separate power systems (for example,

5548-429: Was possible only at low speeds, using a single wire. To enable higher speeds, two additional types of equipment were developed: Earlier dropper wires provided physical support of the contact wire without joining the catenary and contact wires electrically. Modern systems use current-carrying droppers, eliminating the need for separate wires. The present transmission system originated about 100 years ago. A simpler system

5624-430: Was problematic at best; the circumferential contact of the grooved wheel bearing on the underside of the overhead wire provided minimal electrical contact and tended to arc excessively, increasing overhead wire wear. The newer sliding carbon trolley shoe was generally used with a newer grooved overhead trolley wire of a roughly " figure 8 " cross section. The sliding trolley shoe provided better electrical contact (with

5700-476: Was proposed in the 1970s by the Pirelli Construction Company, consisting of a single wire embedded at each support for 2.5 metres (8 ft 2 in) of its length in a clipped, extruded aluminum beam with the wire contact face exposed. A somewhat higher tension than used before clipping the beam yielded a deflected profile for the wire that could be easily handled at 400 km/h (250 mph) by

5776-460: Was used, with the brass contact running inside the groove. When the overhead line was raised in the Simplon Tunnel to accommodate taller rolling stock, a rail was used. A rigid overhead rail may also be used in places where tensioning the wires is impractical, for example on moveable bridges . In modern uses, it is very common for underground sections of trams, metros, and mainline railways to use

#910089