Nove is a town and comune in the province of Vicenza in the region of Veneto , north-eastern Italy , with just over 5,000 inhabitants. It is located on the Brenta river, near Marostica and Bassano del Grappa .
71-490: The town is home of a local network of ceramic industries. The name of the town comes from the antique Italian nove , in the meaning of "new". As matter of fact, the lands where the town is located were considered new because of the lowering of the level of the Brenta. The lowering of the river revealed soft lands rich of clay . The first artisans of the area started using the clay for the production of pottery . The town have
142-526: A beautiful ceramic museum with a Pablo Picasso gallipot and other important pieces of the 18th and 19th century. Nove is twinned with: Ex comuni This article on a location in Veneto is a stub . You can help Misplaced Pages by expanding it . Ceramic A ceramic is any of the various hard, brittle , heat-resistant , and corrosion-resistant materials made by shaping and then firing an inorganic, nonmetallic material, such as clay , at
213-484: A decrease in the material's hardness. The way to inhibit the movement of planes of atoms, and thus make them harder, involves the interaction of dislocations with each other and interstitial atoms. When a dislocation intersects with a second dislocation, it can no longer traverse through the crystal lattice. The intersection of dislocations creates an anchor point and does not allow the planes of atoms to continue to slip over one another A dislocation can also be anchored by
284-424: A different type of atom at the lattice site that should normally be occupied by a metal atom, a substitutional defect is formed. If there exists an atom in a site where there should normally not be, an interstitial defect is formed. This is possible because space exists between atoms in a crystal lattice. While point defects are irregularities at a single site in the crystal lattice, line defects are irregularities on
355-505: A few hundred ohms . The major advantage of these is that they can dissipate a lot of energy, and they self-reset; after the voltage across the device drops below the threshold, its resistance returns to being high. This makes them ideal for surge-protection applications; as there is control over the threshold voltage and energy tolerance, they find use in all sorts of applications. The best demonstration of their ability can be found in electrical substations , where they are employed to protect
426-514: A finer examination of the composition of ceramic artifacts and sherds to determine the source of the material and, through this, the possible manufacturing site. Key criteria are the composition of the clay and the temper used in the manufacture of the article under study: the temper is a material added to the clay during the initial production stage and is used to aid the subsequent drying process. Types of temper include shell pieces, granite fragments, and ground sherd pieces called ' grog '. Temper
497-422: A furnace, a pyroelectric crystal allowed to cool under no applied stress generally builds up a static charge of thousands of volts. Such materials are used in motion sensors , where the tiny rise in temperature from a warm body entering the room is enough to produce a measurable voltage in the crystal. In turn, pyroelectricity is seen most strongly in materials that also display the ferroelectric effect , in which
568-669: A glassy surface, making a vessel less pervious to water. Ceramic artifacts have an important role in archaeology for understanding the culture, technology, and behavior of peoples of the past. They are among the most common artifacts to be found at an archaeological site, generally in the form of small fragments of broken pottery called sherds . The processing of collected sherds can be consistent with two main types of analysis: technical and traditional. The traditional analysis involves sorting ceramic artifacts, sherds, and larger fragments into specific types based on style, composition, manufacturing, and morphology. By creating these typologies, it
639-489: A high temperature. Common examples are earthenware , porcelain , and brick . The earliest ceramics made by humans were fired clay bricks used for building house walls and other structures. Other pottery objects such as pots, vessels, vases and figurines were made from clay , either by itself or mixed with other materials like silica , hardened by sintering in fire. Later, ceramics were glazed and fired to create smooth, colored surfaces, decreasing porosity through
710-413: A plane of atoms. Dislocations are a type of line defect involving the misalignment of these planes. In the case of an edge dislocation, a half plane of atoms is wedged between two planes of atoms. In the case of a screw dislocation two planes of atoms are offset with a helical array running between them. In glasses, hardness seems to depend linearly on the number of topological constraints acting between
781-492: A rotation process called "throwing"), slip casting , tape casting (used for making very thin ceramic capacitors), injection molding , dry pressing, and other variations. Many ceramics experts do not consider materials with an amorphous (noncrystalline) character (i.e., glass) to be ceramics, even though glassmaking involves several steps of the ceramic process and its mechanical properties are similar to those of ceramic materials. However, heat treatments can convert glass into
SECTION 10
#1732852190042852-421: A scratch (linear), induced mechanically either by pressing or abrasion . In general, different materials differ in their hardness; for example hard metals such as titanium and beryllium are harder than soft metals such as sodium and metallic tin , or wood and common plastics . Macroscopic hardness is generally characterized by strong intermolecular bonds , but the behavior of solid materials under force
923-434: A semi-crystalline material known as glass-ceramic . Traditional ceramic raw materials include clay minerals such as kaolinite , whereas more recent materials include aluminium oxide, more commonly known as alumina . Modern ceramic materials, which are classified as advanced ceramics, include silicon carbide and tungsten carbide . Both are valued for their abrasion resistance and are therefore used in applications such as
994-423: A signal). The unit of time measured is the natural interval required for electricity to be converted into mechanical energy and back again. The piezoelectric effect is generally stronger in materials that also exhibit pyroelectricity , and all pyroelectric materials are also piezoelectric. These materials can be used to inter-convert between thermal, mechanical, or electrical energy; for instance, after synthesis in
1065-418: A stable electric dipole can be oriented or reversed by applying an electrostatic field. Pyroelectricity is also a necessary consequence of ferroelectricity. This can be used to store information in ferroelectric capacitors , elements of ferroelectric RAM . The most common such materials are lead zirconate titanate and barium titanate . Aside from the uses mentioned above, their strong piezoelectric response
1136-464: A tensile test. This relationship can be used to describe how the material will respond to almost any loading situation, often by using the Finite Element Method (FEM). This applies to the outcome of an indentation test (with a given size and shape of indenter, and a given applied load). However, while a hardness number thus depends on the stress-strain relationship, inferring the latter from
1207-722: Is complex; therefore, hardness can be measured in different ways, such as scratch hardness , indentation hardness , and rebound hardness. Hardness is dependent on ductility , elastic stiffness , plasticity , strain , strength , toughness , viscoelasticity , and viscosity . Common examples of hard matter are ceramics , concrete , certain metals , and superhard materials , which can be contrasted with soft matter . There are three main types of hardness measurements: scratch, indentation, and rebound. Within each of these classes of measurement there are individual measurement scales. For practical reasons conversion tables are used to convert between one scale and another. Scratch hardness
1278-467: Is employed. Ice templating allows the creation of macroscopic pores in a unidirectional arrangement. The applications of this oxide strengthening technique are important for solid oxide fuel cells and water filtration devices. To process a sample through ice templating, an aqueous colloidal suspension is prepared to contain the dissolved ceramic powder evenly dispersed throughout the colloid, for example Yttria-stabilized zirconia (YSZ). The solution
1349-468: Is exploited in the design of high-frequency loudspeakers , transducers for sonar , and actuators for atomic force and scanning tunneling microscopes . Temperature increases can cause grain boundaries to suddenly become insulating in some semiconducting ceramic materials, mostly mixtures of heavy metal titanates . The critical transition temperature can be adjusted over a wide range by variations in chemistry. In such materials, current will pass through
1420-665: Is known as a scleroscope . Two scales that measures rebound hardness are the Leeb rebound hardness test and Bennett hardness scale. Ultrasonic Contact Impedance (UCI) method determines hardness by measuring the frequency of an oscillating rod. The rod consists of a metal shaft with vibrating element and a pyramid-shaped diamond mounted on one end. There are five hardening processes: Hall-Petch strengthening , work hardening , solid solution strengthening , precipitation hardening , and martensitic transformation . In solid mechanics , solids generally have three responses to force , depending on
1491-459: Is known as the Hall-Petch relationship . However, below a critical grain-size, hardness decreases with decreasing grain size. This is known as the inverse Hall-Petch effect. Hardness of a material to deformation is dependent on its microdurability or small-scale shear modulus in any direction, not to any rigidity or stiffness properties such as its bulk modulus or Young's modulus . Stiffness
SECTION 20
#17328521900421562-480: Is not understood, but there are two major families of superconducting ceramics. Piezoelectricity , a link between electrical and mechanical response, is exhibited by a large number of ceramic materials, including the quartz used to measure time in watches and other electronics. Such devices use both properties of piezoelectrics, using electricity to produce a mechanical motion (powering the device) and then using this mechanical motion to produce electricity (generating
1633-407: Is often confused for hardness. Some materials are stiffer than diamond (e.g. osmium) but are not harder, and are prone to spalling and flaking in squamose or acicular habits. The key to understanding the mechanism behind hardness is understanding the metallic microstructure , or the structure and arrangement of the atoms at the atomic level. In fact, most important metallic properties critical to
1704-491: Is possible to distinguish between different cultural styles, the purpose of the ceramic, and the technological state of the people, among other conclusions. Besides, by looking at stylistic changes in ceramics over time, it is possible to separate (seriate) the ceramics into distinct diagnostic groups (assemblages). A comparison of ceramic artifacts with known dated assemblages allows for a chronological assignment of these pieces. The technical approach to ceramic analysis involves
1775-568: Is responsible for such diverse optical phenomena as night-vision and IR luminescence . Thus, there is an increasing need in the military sector for high-strength, robust materials which have the capability to transmit light ( electromagnetic waves ) in the visible (0.4 – 0.7 micrometers) and mid- infrared (1 – 5 micrometers) regions of the spectrum. These materials are needed for applications requiring transparent armor, including next-generation high-speed missiles and pods, as well as protection against improvised explosive devices (IED). In
1846-413: Is the sclerometer . Another tool used to make these tests is the pocket hardness tester . This tool consists of a scale arm with graduated markings attached to a four-wheeled carriage. A scratch tool with a sharp rim is mounted at a predetermined angle to the testing surface. In order to use it a weight of known mass is added to the scale arm at one of the graduated markings, the tool is then drawn across
1917-453: Is the measure of how resistant a sample is to fracture or permanent plastic deformation due to friction from a sharp object. The principle is that an object made of a harder material will scratch an object made of a softer material. When testing coatings, scratch hardness refers to the force necessary to cut through the film to the substrate. The most common test is Mohs scale , which is used in mineralogy . One tool to make this measurement
1988-436: Is the tendency of a material to fracture with very little or no detectable plastic deformation beforehand. Thus in technical terms, a material can be both brittle and strong. In everyday usage "brittleness" usually refers to the tendency to fracture under a small amount of force, which exhibits both brittleness and a lack of strength (in the technical sense). For perfectly brittle materials, yield strength and ultimate strength are
2059-425: Is then cooled from the bottom to the top on a platform that allows for unidirectional cooling. This forces ice crystals to grow in compliance with the unidirectional cooling, and these ice crystals force the dissolved YSZ particles to the solidification front of the solid-liquid interphase boundary, resulting in pure ice crystals lined up unidirectionally alongside concentrated pockets of colloidal particles. The sample
2130-472: Is then heated and at the same the pressure is reduced enough to force the ice crystals to sublime and the YSZ pockets begin to anneal together to form macroscopically aligned ceramic microstructures. The sample is then further sintered to complete the evaporation of the residual water and the final consolidation of the ceramic microstructure. During ice-templating, a few variables can be controlled to influence
2201-472: Is typically somewhere between the minimum wavelength of visible light and the resolution limit of the naked eye. The microstructure includes most grains, secondary phases, grain boundaries, pores, micro-cracks, structural defects, and hardness micro indentions. Most bulk mechanical, optical, thermal, electrical, and magnetic properties are significantly affected by the observed microstructure. The fabrication method and process conditions are generally indicated by
Nove - Misplaced Pages Continue
2272-399: Is usually identified by microscopic examination of the tempered material. Clay identification is determined by a process of refiring the ceramic and assigning a color to it using Munsell Soil Color notation. By estimating both the clay and temper compositions and locating a region where both are known to occur, an assignment of the material source can be made. Based on the source assignment of
2343-467: Is virtually lossless. Optical waveguides are used as components in Integrated optical circuits (e.g. light-emitting diodes , LEDs) or as the transmission medium in local and long haul optical communication systems. Also of value to the emerging materials scientist is the sensitivity of materials to radiation in the thermal infrared (IR) portion of the electromagnetic spectrum . This heat-seeking ability
2414-886: The 1960s, scientists at General Electric (GE) discovered that under the right manufacturing conditions, some ceramics, especially aluminium oxide (alumina), could be made translucent . These translucent materials were transparent enough to be used for containing the electrical plasma generated in high- pressure sodium street lamps. During the past two decades, additional types of transparent ceramics have been developed for applications such as nose cones for heat-seeking missiles , windows for fighter aircraft , and scintillation counters for computed tomography scanners. Other ceramic materials, generally requiring greater purity in their make-up than those above, include forms of several chemical compounds, including: For convenience, ceramic products are usually divided into four main types; these are shown below with some examples: Frequently,
2485-526: The Hall-Petch equation, hardness , toughness , dielectric constant , and the optical properties exhibited by transparent materials . Ceramography is the art and science of preparation, examination, and evaluation of ceramic microstructures. Evaluation and characterization of ceramic microstructures are often implemented on similar spatial scales to that used commonly in the emerging field of nanotechnology: from nanometers to tens of micrometers (µm). This
2556-451: The amount of force and the type of material: Strength is a measure of the extent of a material's elastic range, or elastic and plastic ranges together. This is quantified as compressive strength , shear strength , tensile strength depending on the direction of the forces involved. Ultimate strength is an engineering measure of the maximum load a part of a specific material and geometry can withstand. Brittleness , in technical usage,
2627-494: The artifact, further investigations can be made into the site of manufacture. The physical properties of any ceramic substance are a direct result of its crystalline structure and chemical composition. Solid-state chemistry reveals the fundamental connection between microstructure and properties, such as localized density variations, grain size distribution, type of porosity, and second-phase content, which can all be correlated with ceramic properties such as mechanical strength σ by
2698-475: The atoms of the network. Hence, the rigidity theory has allowed predicting hardness values with respect to composition. Dislocations provide a mechanism for planes of atoms to slip and thus a method for plastic or permanent deformation. Planes of atoms can flip from one side of the dislocation to the other effectively allowing the dislocation to traverse through the material and the material to deform permanently. The movement allowed by these dislocations causes
2769-513: The brightness and contrast of a digital image. Guided lightwave transmission via frequency selective waveguides involves the emerging field of fiber optics and the ability of certain glassy compositions as a transmission medium for a range of frequencies simultaneously ( multi-mode optical fiber ) with little or no interference between competing wavelengths or frequencies. This resonant mode of energy and data transmission via electromagnetic (light) wave propagation , though low powered,
2840-418: The ceramic family. Highly oriented crystalline ceramic materials are not amenable to a great range of processing. Methods for dealing with them tend to fall into one of two categories: either making the ceramic in the desired shape by reaction in situ or "forming" powders into the desired shape and then sintering to form a solid body. Ceramic forming techniques include shaping by hand (sometimes including
2911-471: The chemical erosion that occurs in other materials subjected to acidic or caustic environments. Ceramics generally can withstand very high temperatures, ranging from 1,000 °C to 1,600 °C (1,800 °F to 3,000 °F). The crystallinity of ceramic materials varies widely. Most often, fired ceramics are either vitrified or semi-vitrified, as is the case with earthenware, stoneware , and porcelain. Varying crystallinity and electron composition in
Nove - Misplaced Pages Continue
2982-534: The class of ceramic matrix composite materials, in which ceramic fibers are embedded and with specific coatings are forming fiber bridges across any crack. This mechanism substantially increases the fracture toughness of such ceramics. Ceramic disc brakes are an example of using a ceramic matrix composite material manufactured with a specific process. Scientists are working on developing ceramic materials that can withstand significant deformation without breaking. A first such material that can deform in room temperature
3053-458: The critical dimensions of an indentation left by a specifically dimensioned and loaded indenter. Common indentation hardness scales are Rockwell , Vickers , Shore , and Brinell , amongst others. Rebound hardness , also known as dynamic hardness , measures the height of the "bounce" of a diamond-tipped hammer dropped from a fixed height onto a material. This type of hardness is related to elasticity . The device used to take this measurement
3124-433: The density of dislocations increases, there are more intersections created and consequently more anchor points. Similarly, as more interstitial atoms are added, more pinning points that impede the movements of dislocations are formed. As a result, the more anchor points added, the harder the material will become. Careful note should be taken of the relationship between a hardness number and the stress-strain curve exhibited by
3195-457: The electrical properties that show grain boundary effects. One of the most widely used of these is the varistor. These are devices that exhibit the property that resistance drops sharply at a certain threshold voltage . Once the voltage across the device reaches the threshold, there is a breakdown of the electrical structure in the vicinity of the grain boundaries, which results in its electrical resistance dropping from several megohms down to
3266-478: The former is far from simple and is not attempted in any rigorous way during conventional hardness testing. (In fact, the Indentation Plastometry technique, which involves iterative FEM modelling of an indentation test, does allow a stress-strain curve to be obtained via indentation, but this is outside the scope of conventional hardness testing.) A hardness number is just a semi-quantitative indicator of
3337-400: The grain level of the microstructure that are responsible for the hardness of the material. These irregularities are point defects and line defects. A point defect is an irregularity located at a single lattice site inside of the overall three-dimensional lattice of the grain. There are three main point defects. If there is an atom missing from the array, a vacancy defect is formed. If there is
3408-460: The group as a whole. General properties such as high melting temperature, high hardness, poor conductivity, high moduli of elasticity , chemical resistance, and low ductility are the norm, with known exceptions to each of these rules ( piezoelectric ceramics , low glass transition temperature ceramics, superconductive ceramics ). Composites such as fiberglass and carbon fiber , while containing ceramic materials, are not considered to be part of
3479-632: The infrastructure from lightning strikes. They have rapid response, are low maintenance, and do not appreciably degrade from use, making them virtually ideal devices for this application. Semiconducting ceramics are also employed as gas sensors . When various gases are passed over a polycrystalline ceramic, its electrical resistance changes. With tuning to the possible gas mixtures, very inexpensive devices can be produced. Under some conditions, such as extremely low temperatures, some ceramics exhibit high-temperature superconductivity (in superconductivity, "high temperature" means above 30 K). The reason for this
3550-443: The interaction with interstitial atoms. If a dislocation comes in contact with two or more interstitial atoms, the slip of the planes will again be disrupted. The interstitial atoms create anchor points, or pinning points, in the same manner as intersecting dislocations. By varying the presence of interstitial atoms and the density of dislocations, a particular metal's hardness can be controlled. Although seemingly counter-intuitive, as
3621-468: The ionic and covalent bonds cause most ceramic materials to be good thermal and electrical insulators (researched in ceramic engineering ). With such a large range of possible options for the composition/structure of a ceramic (nearly all of the elements, nearly all types of bonding, and all levels of crystallinity), the breadth of the subject is vast, and identifiable attributes ( hardness , toughness , electrical conductivity ) are difficult to specify for
SECTION 50
#17328521900423692-529: The manufacturing of today’s goods are determined by the microstructure of a material. At the atomic level, the atoms in a metal are arranged in an orderly three-dimensional array called a crystal lattice . In reality, however, a given specimen of a metal likely never contains a consistent single crystal lattice. A given sample of metal will contain many grains, with each grain having a fairly consistent array pattern. At an even smaller scale, each grain contains irregularities. There are two types of irregularities at
3763-486: The material near its critical temperature, the dielectric effect remains exceptionally strong even at much higher temperatures. Titanates with critical temperatures far below room temperature have become synonymous with "ceramic" in the context of ceramic capacitors for just this reason. Optically transparent materials focus on the response of a material to incoming light waves of a range of wavelengths. Frequency selective optical filters can be utilized to alter or enhance
3834-445: The material until joule heating brings it to the transition temperature, at which point the circuit will be broken and current flow will cease. Such ceramics are used as self-controlled heating elements in, for example, the rear-window defrost circuits of automobiles. At the transition temperature, the material's dielectric response becomes theoretically infinite. While a lack of temperature control would rule out any practical use of
3905-412: The material. The latter, which is conventionally obtained via tensile testing , captures the full plasticity response of the material (which is in most cases a metal). It is in fact a dependence of the (true) von Mises plastic strain on the (true) von Mises stress , but this is readily obtained from a nominal stress – nominal strain curve (in the pre- necking regime), which is the immediate outcome of
3976-410: The mechanical performance of materials and components. It applies the physics of stress and strain , in particular the theories of elasticity and plasticity , to the microscopic crystallographic defects found in real materials in order to predict the macroscopic mechanical failure of bodies. Fractography is widely used with fracture mechanics to understand the causes of failures and also verify
4047-412: The microstructure. The root cause of many ceramic failures is evident in the cleaved and polished microstructure. Physical properties which constitute the field of materials science and engineering include the following: Mechanical properties are important in structural and building materials as well as textile fabrics. In modern materials science , fracture mechanics is an important tool in improving
4118-718: The pore size and morphology of the microstructure. These important variables are the initial solids loading of the colloid, the cooling rate, the sintering temperature and duration, and the use of certain additives which can influence the microstructural morphology during the process. A good understanding of these parameters is essential to understanding the relationships between processing, microstructure, and mechanical properties of anisotropically porous materials. Some ceramics are semiconductors . Most of these are transition metal oxides that are II-VI semiconductors, such as zinc oxide . While there are prospects of mass-producing blue LEDs from zinc oxide, ceramicists are most interested in
4189-441: The raw materials of modern ceramics do not include clays. Those that do have been classified as: Ceramics can also be classified into three distinct material categories: Each one of these classes can be developed into unique material properties. Hardness In materials science , hardness (antonym: softness ) is a measure of the resistance to localized plastic deformation , such as an indentation (over an area) or
4260-406: The resistance to plastic deformation. Although hardness is defined in a similar way for most types of test – usually as the load divided by the contact area – the numbers obtained for a particular material are different for different types of test, and even for the same test with different applied loads. Attempts are sometimes made to identify simple analytical expressions that allow features of
4331-683: The root ceram- is the Mycenaean Greek ke-ra-me-we , workers of ceramic, written in Linear B syllabic script. The word ceramic can be used as an adjective to describe a material, product, or process, or it may be used as a noun, either singular or, more commonly, as the plural noun ceramics . Ceramic material is an inorganic, metallic oxide, nitride, or carbide material. Some elements, such as carbon or silicon , may be considered ceramics. Ceramic materials are brittle, hard, strong in compression, and weak in shearing and tension. They withstand
SECTION 60
#17328521900424402-484: The same, because they do not experience detectable plastic deformation. The opposite of brittleness is ductility . The toughness of a material is the maximum amount of energy it can absorb before fracturing, which is different from the amount of force that can be applied. Toughness tends to be small for brittle materials, because elastic and plastic deformations allow materials to absorb large amounts of energy. Hardness increases with decreasing particle size . This
4473-464: The stress-strain curve, particularly the yield stress and Ultimate Tensile Stress (UTS), to be obtained from a particular type of hardness number. However, these are all based on empirical correlations, often specific to particular types of alloy: even with such a limitation, the values obtained are often quite unreliable. The underlying problem is that metals with a range of combinations of yield stress and work hardening characteristics can exhibit
4544-412: The test surface. The use of the weight and markings allows a known pressure to be applied without the need for complicated machinery. Indentation hardness measures the resistance of a sample to material deformation due to a constant compression load from a sharp object. Tests for indentation hardness are primarily used in engineering and metallurgy . The tests work on the basic premise of measuring
4615-453: The theoretical failure predictions with real-life failures. Ceramic materials are usually ionic or covalent bonded materials. A material held together by either type of bond will tend to fracture before any plastic deformation takes place, which results in poor toughness in these materials. Additionally, because these materials tend to be porous, the pores and other microscopic imperfections act as stress concentrators , decreasing
4686-460: The toughness further, and reducing the tensile strength . These combine to give catastrophic failures , as opposed to the more ductile failure modes of metals. These materials do show plastic deformation . However, because of the rigid structure of crystalline material, there are very few available slip systems for dislocations to move, and so they deform very slowly. To overcome the brittle behavior, ceramic material development has introduced
4757-558: The use of glassy, amorphous ceramic coatings on top of the crystalline ceramic substrates. Ceramics now include domestic, industrial, and building products, as well as a wide range of materials developed for use in advanced ceramic engineering, such as semiconductors . The word ceramic comes from the Ancient Greek word κεραμικός ( keramikós ), meaning "of or for pottery " (from κέραμος ( kéramos ) 'potter's clay, tile, pottery'). The earliest known mention of
4828-446: The wear plates of crushing equipment in mining operations. Advanced ceramics are also used in the medical, electrical, electronics, and armor industries. Human beings appear to have been making their own ceramics for at least 26,000 years, subjecting clay and silica to intense heat to fuse and form ceramic materials. The earliest found so far were in southern central Europe and were sculpted figures, not dishes. The earliest known pottery
4899-425: Was found in 2024. If a ceramic is subjected to substantial mechanical loading, it can undergo a process called ice-templating , which allows some control of the microstructure of the ceramic product and therefore some control of the mechanical properties. Ceramic engineers use this technique to tune the mechanical properties to their desired application. Specifically, the strength is increased when this technique
4970-497: Was made by mixing animal products with clay and firing it at up to 800 °C (1,500 °F). While pottery fragments have been found up to 19,000 years old, it was not until about 10,000 years later that regular pottery became common. An early people that spread across much of Europe is named after its use of pottery: the Corded Ware culture . These early Indo-European peoples decorated their pottery by wrapping it with rope while it
5041-528: Was still wet. When the ceramics were fired, the rope burned off but left a decorative pattern of complex grooves on the surface. The invention of the wheel eventually led to the production of smoother, more even pottery using the wheel-forming (throwing) technique, like the pottery wheel . Early ceramics were porous, absorbing water easily. It became useful for more items with the discovery of glazing techniques, which involved coating pottery with silicon, bone ash, or other materials that could melt and reform into
#41958