Matbro was a brand of lifting equipment , popular with farmers . Matbro produced a wide range of all terrain forklifts and telescopic handlers in their distinctive yellow livery , using engines derived from Ford and Perkins . Matbro began operating at a loss in the late 1990s and in the end went under in 2003 after accounting issues in their parent company Powerscreen. The old designs were then sold to the tractor company John Deere , which sub-licensed them to heavy lifting company Terex , who continued to evolve the designs, with new ideas such as side-mounted engines instead of rear ones and hydrostatic drive.
49-849: The company, named after its founders the Mathew brothers, produced forklift trucks in Horley in Surrey , England . Between 1964 and 1971 a range of forklifts carrying loads of 8000 lb to 17,765 lb, named the Yard Model and the Compact Model were produced. These used axles made by GKN Centrax at Newton Abbot in Devon , under licence from the Rockwell-Standard . The frequent failure of axles supplied by Centrax for loads heavier than recommended by Rockwell led to
98-485: A sod loader . Comes in sit-down center control. Usually has an internal combustion engine. Engines are almost always diesel, but sometimes operate on kerosene, and sometimes use propane injection as a power boost. Some old units are two-stroke compression ignition; most are four-stroke compression ignition. North American engines come with advanced emission control systems. Forklifts built in countries such as Iran or Russia will typically have no emission control systems. At
147-518: A British company named Lansing Bagnall , now part of KION Group , developed what was claimed to be the first narrow-aisle electric-reach truck. That development changed the design of warehouses leading to narrower aisles and higher load-stacking, which increased storage capability. During the 1950s and 1960s, operator safety became a concern due to increasing lifting heights and capacities. Safety features such as load backrests and operator cages called overhead guards, began to be added to forklifts. In
196-521: A battery and subsequently used to drive electric motors to power the forklift. This method of propulsion produces no local emissions, can be refueled in three minutes, and is often used in refrigerated warehouses as its performance is not degraded by lower temperatures. As of 2024, approximately 50,000 hydrogen forklifts are in operation worldwide (the bulk of which are in the U.S.), as compared with 1.2 million battery electric forklifts that were purchased in 2021. A typical counterbalanced forklift contains
245-406: A building with a relatively small surface area. Counterbalance-type order-picking truck similar to the guided very-narrow-aisle truck, except that the operator and the controls which operate the machine are in a cage welded to the mast. The operator wears a restraint system to protect them against falls. Otherwise, the description is the same as guided very-narrow-aisle truck. Also referred to as
294-474: A control to raise and lower the forks (also known as blades or tines), the operator can tilt the mast to compensate for a load's tendency to angle the blades toward the ground and risk slipping off the forks. Tilt also provides a limited ability to operate on non-level ground. Skilled forklift operators annually compete in obstacle and timed challenges at regional forklift rodeos. Powered pallet truck, usually electrically powered. Low lift trucks may be operated by
343-417: A driver's traditional experience with other wheeled vehicles. While steering, as there is no caster action, it is unnecessary to apply steering force to maintain a constant rate of turn. Another critical characteristic of the forklift is its instability. The forklift and load must be considered a unit with a continually varying center of gravity with every movement of the load. A forklift must never negotiate
392-581: A dual fuel gasoline/liquified propane-powered truck. UL 558 is a two-stage safety standard. The basic standards are referred to as G, D, LP, and G/LP. They are considered by Underwriters Laboratories to be the bare minimum required for a lift truck. This is a voluntary standard, and there is no requirement in North America at least by any Government Agency for manufacturers to meet this standard. The slightly more stringent safety standards GS, DS, LPS, and GP/LPS do provide some minimal protection; however, it
441-400: A forklift truck. Freddy's patent application referenced specific drive methods, allowing competitors to enter the market by offering alternative methods, but using the same articulating principle. These are rail- or wire-guided and available with lift heights up to 40 feet non-top-tied and 98 feet top-tied. Two forms are available: 'man-down' and 'man-riser', where the operator elevates with
490-550: A legal case which eventually went before Lord Denning in the Court of Appeal of England and Wales . This model with pivot steering and equal sized wheels was the basis of the first radial arm machines, the RAM40 with 40 cwt (2 imperial tons) lift capacity, produced c.1980. This was soon improved with a telescopic boom, producing the Teleram 40. These compact machines with the operator sitting above
539-526: A pallet. Often, forklift drivers are guided into the bay by guide rails on the floor and the pallet is placed on cantilevered arms or rails. These maneuvers require well-trained operators. Since every pallet requires the truck to enter the storage structure, damage is more common than with other types of storage. In designing a drive-in system, dimensions of the fork truck, including overall width and mast width, must be carefully considered. Forklift hydraulics are controlled either with levers directly manipulating
SECTION 10
#1732855105807588-450: A person seated on the machine, or by a person walking alongside, depending on the design. Usually electrically powered. A stacker may be operated by a person seated on the machine, or by a person walking alongside, depending on the design. Variant on a Rider Stacker forklift, designed for narrow aisles. They are usually electrically powered and often have the highest storage-position lifting ability. A reach truck's forks can extend to reach
637-443: A personnel lift without the fitting of specific safety equipment, such as a "cherry picker" or "cage". Forklifts are a critical element of warehouses and distribution centers. It is considered imperative that these structures be designed to accommodate their efficient and safe movement. In the case of Drive-In/Drive-Thru Racking, a forklift needs to travel inside a storage bay that is multiple pallet positions deep to place or retrieve
686-449: A reach truck, except the operator either rides in a cage welded to the fork carriage or walks alongside, dependent on design. If the operator is riding in the order picking truck, they wear a specially-designed safety harness to prevent falls. A special toothed grab holds the pallet to the forks. The operator transfers the load onto the pallet one article at a time by hand. This is an efficient way of picking less-than-pallet-load shipments and
735-488: A specified maximum weight and a specified forward center of gravity . This information is located on a nameplate provided by the manufacturer, and loads must not exceed these specifications. In many jurisdictions, it is illegal to alter or remove the nameplate without the permission of the forklift manufacturer. An important aspect of forklift operation is that it must have rear-wheel steering . While this increases maneuverability in tight cornering situations, it differs from
784-412: A turn at speed with a raised load, where centrifugal and gravitational forces may combine to cause a tip-over accident. The forklift is designed with a load limit for the forks which is decreased with fork elevation and undercutting of the load (i.e., when a load does not butt against the fork "L"). A loading plate for loading reference is usually located on the forklift. A forklift should not be used as
833-431: A valve). Forklift manufacturers make valves and hose routing accessories, but the parts and labor to install can be prohibitively expensive. Other ways include adding a solenoid valve in conjunction with a hose or cable reel that diverts oil flow from an existing function. However, hose and cable reels can block the operator's view and are easily damaged. There are many national as well as continental associations related to
882-505: Is a stub . You can help Misplaced Pages by expanding it . Forklift trucks A forklift (also called industrial truck, lift truck , jitney , hi-lo , fork truck , fork hoist , and forklift truck ) is a powered industrial truck used to lift and move materials over short distances. The forklift was developed in the early 20th century by various companies, including Clark , which made transmissions , and Yale & Towne Manufacturing , which made hoists . Since World War II,
931-468: Is able to rotate the truck 360 degrees in its own footprint or strafe sideways without turning the truck cabin. In North America, some internal combustion-powered industrial vehicles carry Underwriters Laboratories ratings that are part of UL 558. Industrial trucks that are considered "safety" carry the designations GS (Gasoline Safety) for gasoline-powered, DS (Diesel Safety) for diesel-powered, LPS (Liquid Propane Safety) for liquified propane or GS/LPS for
980-607: Is credited with perfecting the principle of an articulated design in about 1982, receiving an award in 2002 from the UK's Fork Lift Truck Association for Services to the Forklift Industry and the Queen's Award for Innovation in 2003. He took inspiration from the hand pallet truck and found that by reversing the triangle of stability and changing the weight distribution he could solve the issues that had long eluded earlier attempts of articulating
1029-585: Is extremely minimal. In the past, Underwriter's Laboratory offered specialty EX and DX safety certifications. UL 583 is the Electric equivalent of UL 558 . As with UL 558 it is a two-stage standard. These are for operation in potentially explosive atmospheres found in chemical, petrochemical, pharmaceutical, food and drink, logistics or other fields handling flammable material. Commonly referred to as mainly Miretti or sometimes Pyroban trucks in Europe, they must meet
SECTION 20
#17328551058071078-580: Is often stored in a gas cylinder mounted to the rear of the truck. This allows for quick changing of the cylinder once the LPG runs out. LPG trucks are quieter than their diesel counterparts, while offering similar levels of performance. Powered by lead-acid batteries or, increasingly, lithium-ion batteries ; battery-electric types include: cushion-tire forklifts, scissor lifts, order pickers, stackers, reach trucks and pallet jacks. Electric forklifts are primarily used indoors on flat, even surfaces. Batteries prevent
1127-407: Is popular for use in large distribution centers. A counterbalance-type sit-down rider electric forklift fitted with a specialized mast assembly. The mast is capable of rotating 90 degrees, and the forks can then advance like on a reach mechanism, to pick up full pallets. Because the forklift does not have to turn, the aisles can be exceptionally narrow, and if wire guidance is fitted in the floor of
1176-513: Is positioned up front on the left-hand side. The area to the right of the cab is called the bed or platform. This contains a central section within it, called the well, where the forks are positioned. The mast and forks reach out to lift the load at its central point and lower it onto the bed. Driving forwards with a load carried lengthways allows long goods, typically timber, steel, concrete or plastics, to be moved through doorways and stored more easily than via conventional forklift trucks. Similar to
1225-740: The American National Standards Institute (ANSI) to the Industrial Truck Standards Development Foundation (ITSDF) after multi-year negotiations. ITSDF is a non-profit organization whose only purpose is the promulgation and modernization of the B56 standard. Other forklift safety standards have been implemented in the United States by the Occupational Safety and Health Administration (OSHA) and in
1274-606: The United Kingdom by the Health and Safety Executive . In many countries, forklift truck operators must be trained and certified to operate forklift trucks. Certification may be required for each individual class of lift that an operator would use. Lansing Bagnall Lansing Bagnall , later known as Lansing Linde , was a British forklift truck manufacturer based in Kingsclere Road, Basingstoke , England. The company
1323-455: The attachment features). As mentioned in the preceding section, replacing or adding an attachment may reduce (down-rate) the safe lifting capacity of the forklift truck (See also General operations, below). Forklift attachment manufacturers offer online calculators to estimate the safe lifting capacity when using a particular attachment. However, only the forklift truck manufacturer can give accurate lifting capacities. Forklifts can be re-rated by
1372-419: The automatic gearbox and just in front of the engine proved popular with farmers for their ability to go almost anywhere and do a wide range of jobs, while being able to manoeuvre in confined spaces. [REDACTED] Media related to Matbro vehicles at Wikimedia Commons This article about a mechanical engineering topic is a stub . You can help Misplaced Pages by expanding it . This agriculture article
1421-428: The building the machine can almost work on its own. Masts on this type of machine tend to be very high. The higher the racking that can be installed, the higher the density the storage can reach. This sort of storage system is popular in cities where land prices are very high, as by building the racking up to three times higher than normal and using these machines, it is possible to stock a much larger amount of material in
1470-404: The development and use of the forklift truck has greatly expanded worldwide. Forklifts have become an indispensable piece of equipment in manufacturing and warehousing. In 2013, the top 20 manufacturers worldwide posted sales of $ 30.4 billion, with 944,405 machines sold. Developments from the middle of the 19th century to the early 20th century led to today's modern forklifts. The forerunners of
1519-501: The development of the first electrically-powered forklifts, along with the use of standardized pallets in the late 1930s, helped to increase the popularity of forklift trucks. The start of World War II , like World War I before it, spurred the use of forklift trucks in the war effort. Following the war, more efficient methods for storing products in warehouses were implemented, and warehouses needed more maneuverable forklift trucks that could reach greater heights. For example, in 1954,
Matbro - Misplaced Pages Continue
1568-400: The emission of harmful fumes and are recommended for indoor facilities, such as food-processing and healthcare sectors. Forklifts have also been identified as a promising application for reuse of end-of-life automotive batteries. Hydrogen fuel cell forklifts are powered by a chemical reaction between hydrogen and oxygen. The reaction is used to generate electricity which can then be stored in
1617-466: The following components: Below is a list of common forklift attachments: Any attachment on a forklift will reduce its nominal load rating, which is computed with a stock fork carriage and forks. The actual load rating may be significantly lower. It is possible to replace an existing attachment or add one to a lift that does not already have one. Considerations include forklift type, capacity, carriage type, and number of hydraulic functions (that power
1666-399: The forklift can place the boat into the water, as well as remove it when the boating activity is finished. Marina forklifts are unique among most other forklifts in that they feature a "negative lift" cylinder. This type of cylinder allows the forks to actually descend lower than ground level. Such functionality is necessary, given that the ground upon which the forklift operates is higher than
1715-483: The hydraulic valves or by electrically controlled actuators, using smaller "finger" levers for control. The latter allows forklift designers more freedom in ergonomic design. Forklift trucks are available in many variations and load capacities. In a typical warehouse setting, most forklifts have load capacities between one and five tons. Larger machines, up to 50 tons lift capacity, are used for lifting heavier loads, including loaded shipping containers . In addition to
1764-493: The industrial truck sector. Some of the major organizations include: There are many significant contacts among these organizations and they have established joint statistical and engineering programs. One program is the World Industrial Trucks Statistics (WITS) which is published every month to the association memberships. The statistics are separated by area ( continent ), country and class of machine. While
1813-518: The late 1980s, ergonomic design began to be incorporated in new forklift models to improve operator comfort, reduce injuries, and increase productivity. During the 1990s, undesirable exhaust emissions from forklift operations began to be tackled, which led to emission standards being implemented for forklift manufacturers in various countries. The introduction of AC power forklifts, along with fuel cell technology, were refinements in continuing forklift development. Forklifts are rated for loads at
1862-434: The load for increased visibility or for multilevel 'break bulk' order picking. This type of truck, unlike articulated narrow-aisle trucks, requires a high standard of floor flatness. These lifts are found in places like marinas and boat storage facilities. Featuring tall masts, heavy counterweights, and special paint to resist seawater-induced corrosion , they are used to lift boats in and out of storage racks. Once out,
1911-429: The load, hence the name. There are two types: Standard forklifts use a counterweight at the rear of the truck to offset, or counterbalance, the weight of a load carried at the front of the truck. Electric-powered forklifts utilise the weight of the battery as a counterweight and are typically smaller in size as a result. A sideloader is a piece of materials-handling equipment designed for long loads. The operator's cab
1960-526: The manufacturer and have a new specification plate attached to indicate the changed load capacity with the attachment in use. In the context of attachment, a hydraulic function consists of a valve on the forklift with a lever near the operator that provides two passages of pressurized hydraulic oil to power the attachment features. Sometimes an attachment has more features than the forklift has hydraulic functions and one or more need to be added. There are many ways of adding hydraulic functions (also known as adding
2009-485: The modern forklift were manually powered hoists used to lift loads. In 1906, the Pennsylvania Railroad introduced battery-powered platform trucks for moving luggage at their Altoona, Pennsylvania , station. World War I saw the development of different types of material-handling equipment in the United Kingdom by Ransomes, Sims & Jefferies of Ipswich. This was in part due to the labor shortages caused by
Matbro - Misplaced Pages Continue
2058-489: The other end of the spectrum from the counterbalanced forklift trucks are more 'high-end' specialty trucks. Articulating counterbalance trucks are designed to be both able to offload trailers and place the load in narrow aisle racking. The central pivot of the truck allows loads to be stored in racking at a right angle to the truck, reducing space requirements (therefore increasing pallet storage density) and eliminating double handling from yard to warehouse. Frederick L Brown
2107-954: The requirements of the ATEX 94/9/EC Directive if used in Zone 1, 2, 21 or 22 areas and be maintained accordingly. In order to decrease work wages, reduce operational cost and improve productivity, automated forklifts have also been developed. Automated forklifts are also called forked automated guided vehicles and are already available for sale. Engines may be diesel, kerosene, gasoline, natural gas, butane, or propane-fueled, and may be either two-stroke spark ignition, four-stroke spark ignition (common), two-stroke compression ignition, and four-stroke compression ignition (common). North American Engines come with advanced emission control systems. Forklifts built in countries such as Iran or Russia will typically have no emission control systems. These forklifts use an internal combustion engine modified to run on LPG . The fuel
2156-465: The statistics are generic and do not count production from most of the smaller manufacturers, the information is significant for its depth. These contacts have brought to a common definition of a Class System to which all the major manufacturers adhere. Forklift safety is subject to a variety of standards worldwide. The most important standard is the ANSI B56—of which stewardship has now been passed from
2205-512: The successful private forklift truck manufacturer Henley Forklift, which had been founded in 1966 and developed through the early 1970s, earning three Queen's Awards for export achievement. Lansing Bagnall was acquired by Linde AG in 1989 and now operates under the Linde Lansing brand name. In September 2006, Linde announced their intention to float or sell the materials handling business that included Linde Lansing. This article related to
2254-459: The war. In 1917, Clark in the United States began developing and using powered tractor and powered lift tractors in its factories. In 1919, the Towmotor Company and, in 1920, Yale & Towne Manufacturing , entered the lift truck market in the United States. Continuing development and expanded use of the forklift continued through the 1920s and 1930s. The introduction of hydraulic power and
2303-429: The water level below. Additionally, marina forklifts feature some of the longest forks available, with some up to 24 feet long. The forks are also typically coated in rubber to prevent damage to the hull of the boats that rest on them. Omnidirectional technology (such as Mecanum wheels ) can allow a forklift truck to move forward, diagonally and laterally, or in any direction on a surface. An omnidirectional wheel system
2352-532: Was bought out of bankruptcy in 1943 by Emmanuel Kaye and John R Sharp and renamed after themselves as J E Shay Ltd. At that time, the company made petrol and electric, industrial and station platform tractors. Later, the company went on to produce forklift trucks. Operating as Lansing Bagnall and Shay's in 1946. The company's first factory in Basingstoke was opened, in March 1949. In 1976, Lansing Bagnall acquired
2401-591: Was known for the invention of the reach truck. Later, it was merged into Linde Material Handling which is now part of KION Group . The business was started as a company office in 1920 when W G Bagnall arrived in London as a representative of Lansing company of Michigan. In 1930, the parent company, Lansing, ceased manufacturing operations, so Bagnall took the charge and incorporated the company in 1937 as Lansing Bagnall and Company Limited in Isleworth,London. The company
#806193