75-526: L98 may refer to: L98 Cadet Rifles Luna (Orca) , an animal whose official name is L98 A variant of the GM small-block engine used in Holden cars [REDACTED] Topics referred to by the same term This disambiguation page lists articles associated with the same title formed as a letter–number combination. If an internal link led you here, you may wish to change
150-500: A STANAG magazine , usually with a 30-round capacity. Initially issued magazines were aluminium Colt magazines which were not particularly robust, leading to a steel replacement being produced by ROF Radway Green . These magazines were then replaced during the A2 upgrade programme with two new steel magazines by Heckler & Koch ; the main variant is for live ammunition, and the other is exclusively used for blank ammunition. The blank variant
225-447: A complication, as the rate of fire dropped but the pressure and time curve of the rounds were different. The 4.85mm round was based on the 5.56mm case in anticipation of the need to convert calibres. The barrel was changed easily, but the gas ports were much larger. Pressure problems had less of an effect on the LSW due to its longer barrel. After receiving feedback from users and incorporating
300-703: A fact picked up by the UK media, entertainment industry, and members of the House of Lords. Special Air Service sergeant Chris Ryan regarded the SA80s as being "poor-quality, unreliable weapons at the best of times, prone to stoppages, and it seemed pretty tough to have to rely on them". Immediately after the Gulf War , the Ministry of Defence (MOD) commissioned the LANDSET Report, into
375-522: A forward post vertical blade foresight, installed on a bracket above the gas block. The rear sight can be adjusted for windage, and the foresight—elevation. In place of the SUSAT, a passive night vision CWS scope can be used. More recently, weapons used by some Royal Marines, Infantry, RAF Regiment, Ministry of Defence Police and soldiers with a dismounted close combat role in operations in Afghanistan have had
450-415: A long and continuous life and it was estimated by the trials specialists from Enfield that this weapon would ultimately be superior in the 4.85mm configuration. For the 4.85mm round, both propellant and projectile were at the beginning of their respective development curves. Weight for weight, more rounds of ammunition could be carried by an individual soldier – a considerable advantage on the battlefield. It
525-630: A part in the final decision. In 1976, the prototypes were ready to undergo trials. After NATO's decision to standardise ammunition among its members, Enfield engineers re-chambered the rifles to the American 5.56×45mm NATO M193 cartridge. The newly redesigned 5.56mm version of the XL64E5 became known as the XL70E3. The left-handed XL68 was also re-chambered in 5.56×45mm as the XL78. The 5.56mm light support weapon variant,
600-544: A person's ribs without embedding into bone, and a ribbed section for rope cutting. The bayonet handle is shaped so as to allow the bayonet to be used as a fighting knife in its own right. The issued scabbard features a saw blade for use on wood, a sharpening stone to hone the bayonet, and a bottle opener. When combined with the bayonet, it also forms a wire cutter. When soldiers from the Princess of Wales's Royal Regiment went into battle with fixed bayonets on their SA80s during
675-424: A redesigned cocking handle, modified bolt, extractor and a redesigned hammer assembly that produces a slight delay in the hammer's operation in continuous fire mode, improving reliability and stability. The rifle and the LSW underwent modifications, and the programme also saw the introduction of a carbine variant. The Ministry of Defence describes the A2 revision as "producing the most reliable weapons of their type in
750-399: A stoppage in the first magazine fired. Some platoon commanders considered that casualties would have occurred due to weapon stoppages if the enemy had put up any resistance in the trench and bunker clearing operations. Even discounting the familiarisation period of desert conditions, when some may have still been using the incorrect lubrication drill, stoppages continued to occur." The report
825-498: A tool to clear. The Individual Weapon fired 165 battlefield missions, each comprising 150 rounds over 8 mins 40 secs. A total of 24,750 rounds were fired and suffered only 51 stoppages. Out of 165 battlefield missions, the A2 passed 156; the nine failures stoppages were easily cleared and not mission critical. The L85A2 achieved a 95% success rate, above the operational requirement of 90%, and its nearest rival of popular choice achieved only 47%. Originally slated for introduction in 2002,
SECTION 10
#1732859106273900-415: Is 10,000 rounds, meaning they might never suffer stoppages during their lifetimes. Mean rounds between failures was the measure of the average number of rounds that are fired between failures of a battlefield mission test. A battlefield mission was counted as a failure when there was more than one stoppage that the soldier could clear immediately on their own or there was a stoppage that required an armourer or
975-409: Is a magazine-fed squad automatic weapon originally intended to provide fire support at a fireteam level. The weapon has a heavier, longer 646 millimetres (25.4 in) barrel than the rifle and features a shorter handguard with an integrated bipod protruding from the front. The stock has a shoulder strap to take the weapon's weight in the prone position and a rear vertical grip for better control of
1050-408: Is also the standard sighting arrangement for the LSW variant. Mounted on the SUSAT's one-piece, pressure die-cast aluminium body are a set of back-up iron sights that consist of a front blade and small rear aperture. Rifles used with other branches of the armed forces when not on operations are configured with fixed iron sights, consisting of a flip rear aperture housed inside the carrying handle and
1125-404: Is for use in difficult environmental conditions, while the third setting ("Off") prevents any gas from reaching the piston and is used to launch rifle grenades . The weapon uses a rotating cylindrical bolt that contains seven radially mounted locking splines, an extractor and casing ejector. The bolt's rotation is controlled by a cam stud that slides inside a helical camming guide machined into
1200-408: Is identified by yellow stripes on the magazine, and is designed to prevent the unintentional loading of live rounds. This magazine has less internal length so that live rounds will not fit, while still fitting blank rounds, which are shorter. Blank rounds will fit into the live-round magazine, but the difference in length increases the chance of a stoppage. The Magpul Industries polymer EMAG magazine
1275-493: Is issued on a scale of one per fireteam, and is used with fragmentation, high-explosive dual-purpose (HEDP), red phosphorus, white illuminating parachute, infra-red illuminating parachute, practice, and drill ammunition, with buckshot ammunition also being intended for adoption. The addition of the UGL adds another 1.12 kg to the L85A2's weight. The L86 Light Support Weapon (LSW)
1350-407: Is located at the left side of the receiver, just aft of the magazine). A cross bolt type safety prevents accidental firing and is located above the trigger; the "safe" setting blocks the movement of the trigger. The magazine release button is placed above the magazine housing, on the left side of the receiver. When the last cartridge is fired from the magazine, the bolt and bolt carrier assembly lock to
1425-577: Is supplied with a sling, blank-firing adaptor , and cleaning kit. The rifle can be adapted to use .22 Long Rifle training ammunition with a special conversion kit. The Small Arms Weapons Effects Simulator can be used on the L85 when in training with blank ammunition . On operations with ground close combat units (Infantry, Royal Marines, RAF Regiment), the rifle is often fitted with an LLM01 Laser Light Module and deployable bipod mounted within an optional front grip. There are four main variants that make up
1500-676: The Battle of Al Amara in Iraq on 14 May 2004, it was the first time fixed bayonets had been used by British troops since the Falklands War . On several occasions, fixed bayonets were used during the Afghanistan conflict. The bayonet cannot be fitted to the L22 Carbine or L86 Light Support Weapon. As a result, soldiers equipped with the latter sometimes swapped their weapons for vehicle crewmen's L85s when clearing trenches during Operation Granby . The SA80
1575-585: The British Ministry of Defence in 1966 and 1969. During the development of the SA80, a bullpup conversion was made of an AR-18 and a Stoner 63 at Enfield due to the fact they could be used with stocks folded/without stocks which allowed the bullpup conversion and were later chambered in the experimental 4.85x49mm round. A bullpup conversion of the AR-15 was previously considered but the buffer tube in stock prevented
SECTION 20
#17328591062731650-587: The EM-1 and EM-2 . The latter was brought into service briefly as "Rifle, Automatic, Calibre .280, Number 9". When NATO standardised on the 7.62mm rifle cartridge as the standard calibre for its service rifles , further development of these rifles was discontinued and the British Army adopted the 7.62 mm L1A1 Self-Loading Rifle semi-automatic rifle , a licence-built version of the Belgian FN FAL . In 1969,
1725-704: The L4 Light Machine Gun (a modernised Bren ), and the L7A2 General Purpose Machine Gun as used at section level. Regular infantry, Royal Marine units, and the RAF Regiment were to change over by 1987, remaining regular army units by 1990, remaining RAF units by 1991, Territorial Army units by 1991–1993, and the Royal Navy by 1993. In 1994, production was officially completed. More than 350,000 L85 rifles and L86 LSWs had been manufactured for
1800-620: The Ruger Mini-14 in 1983, although small stocks of the L85 were also acquired for the purpose of familiarisation training as many of its personnel attend courses or attachments in Britain. The Regiment later acquired an additional 400 L85A2 rifles in 2015 to replace the Mini-14 as the standard-issue rifle. The Royal Gibraltar Regiment , which is more closely integrated with the British Army, adopted
1875-666: The XL64E5 rifle (also called the "Enfield Individual Weapon") and a light support weapon known as the XL65E4 light machine gun . The sheet metal construction and the design of the bolt, bolt carrier, guide rods and the weapon's disassembly showed strong similarities to the Armalite AR-18 which was manufactured under licence from 1975 to 1983 by the Sterling Armaments Company of Dagenham , Essex , and which had been tested by
1950-549: The "HK A2" marking on the top of the weapon just forward of the buttplate and the distinctive comma-shaped cocking handle (shaped to aid the ejection of the empty round casing and prevent stoppages). Continued testing of the L85A2 in adverse conditions demonstrates its reliability over contemporary rifles, including the M16. Although it is heavier than most conventional and more modern bullpup rifles, its full-length barrel gives higher muzzle velocities and better terminal performance than both
2025-592: The 1980s) is a British family of 5.56×45mm NATO service weapons used by the British Army . The L85 Rifle variant has been the standard issue service rifle of the British Armed Forces since 1987, replacing the L1A1 Self-Loading Rifle . The prototypes were created in 1976, with production of the A1 variant starting in 1985 and ending in 1994. The A2 variant came to be as the result of a significant upgrade in
2100-570: The American M4 carbine and M16 assault rifle . Rounds from an M4 will only reliably fragment out to 50–100 metres, while the L85A2 and M16 allowed fragmentation out to 150–200 metres and the L86A2 has an even longer fragmentation range. Despite these modifications, the L86A2 was supplemented with a belt-fed machine gun. British troops were issued with FN Minimi machine guns to add suppressive fire out to 300 metres. The weapon drills were changed with
2175-518: The British Armed Forces, with the former variant comprising 95% of the total run, with over 21,700 L98A1 rifles were produced for cadet use. The production line was broken up shortly afterwards, with the Nottingham facility closing in 2001. Upgrade programmes and requirements for spare and replacement parts have since been fulfilled by then British-owned Heckler & Koch , which later reopened
2250-719: The Defence and Security Equipment International event and official adoption taking place in 2018. The changes from the SA80A2 design include a modification to the upper receiver and a full-length rail system for optional add-ons such as a vertical foregrip, laser pointer and torch. It also includes a weight saving of 100 g and a new Flat Dark Earth coating offering improved durability and better camouflage across various environments. The Mid Life Improvement (MLI) project received an initial investment of £5.4 million to have 5,000 weapons upgraded initially, with plans for more weapons to be upgraded in
2325-561: The E3/E4 variants. SA80 development was complicated from the start. One complication was at least three project staffing changes at the Royal Small Arms Factory, which resulted in repetitive testing. One problem with the design of the gun itself was that the cases would be ejected at constantly varying angles as it heated up and the rate of fire changed, resulting in a large ejection port. The conversion from 4.85mm to 5.56mm also caused
L98 - Misplaced Pages Continue
2400-512: The Enfield factory began work on a brand new family of weapons, chambered in a newly designed British 4.85×49mm intermediate cartridge. While the experimental weapon family was very different from the EM-2 in internal design and construction methods, its bullpup configuration with an optical sight was a clear influence on the design of what was to become the SA80. The system was to be composed of two weapons:
2475-567: The Enfield site's total of 230, with the rest being outsourced to subcontractors. Since the plant kept low stocks of pre-produced components, significant delays were incurred if subcontracted components were late in arriving at the Nottingham site or did not meet required tolerances. When the L85A1 and L86A1 were first sent into major combat during the Gulf War , individual performance was far from adequate. The L85A1 proved unreliable in semi-automatic mode, and slightly better in fully automatic mode, while
2550-468: The L85 rifle (with optional Grip Pod downgrip), and a new vortex style flash eliminator was introduced as an Urgent Operational Requirement ; initially introduced for use by selected units in 2007, the upgrade package was subsequently rolled out on a more general basis from 2009 onwards. The SA80A3 was first unveiled in prototype form in September 2016 with working models on display in September 2017 at
2625-640: The L86 was a target of criticism on much the same basis as the L85. The LSW has the additional issue of its inability to deliver sustained automatic fire as it lacks a belt feed. This is common with any light support weapon derived from a rifle, for example the heavy-barrel FN FAL. L64 L64 may refer to: The tactical numbering of the Zeppelin LZ 109 The L64/65 British assault rifle The FAA identifier for Desert Center Airport [REDACTED] Topics referred to by
2700-473: The LSW's bipod lock often failed to hold the bipod legs in closed position, the plastic furniture was melted by insect repellent, metal parts were quick to rust in jungle environments, and the weapon's mechanism was highly susceptible to dusty and arctic environments. These problems were not helped by the production process. The SA80 series was produced from metal stampings. While RSAF Enfield had previous experience in manufacturing stamped-metal firearms, this
2775-604: The Luchaire grenade; when these experienced problems with premature detonation, the L85A1 HE grenade was adopted in their place. Various underbarrel grenade launcher models were trialled, including the M203 and a proprietary "Enfield Close Assault Weapon" developed by Royal Ordnance. It was eventually decided that the L17A2/L123 40mm Underslung Grenade Launcher (UGL) should be adopted; this
2850-497: The Nottingham site. As responsibility for the funding and supply of the home defence regiments of the British Overseas Territories has been handed to the local governments of the territories, despite the regiments themselves coming under command of the national (British) government and being loosely integrated with the British Army, the SA80 was not automatically supplied to these units. The Bermuda Regiment adopted
2925-786: The SA80 family: the L85 Rifle , the L86 Light Support Weapon , the L22 Carbine and the L98 Cadet rifle . The L85 Rifle , referred to on occasion as the L85 Individual Weapon (IW) , is the standard rifle for the British Armed Forces. When initially adopted for service, the L85's grenade-launching ability was fulfilled by then-conventional rifle grenades, namely the L74A1 high-explosive anti-tank (HEAT) and L75A1 HEAT-APERS versions of
3000-790: The SA80 from the outset. The Falkland Islands Defence Force adopted the Steyr AUG (another 5.56×45mm bullpup rifle) which served until 2019 when the Defence Force adopted the L85A2 as part of a wider effort to align its weapons, training and procedures with those of the British Armed Forces. The L85 is in use with the Jamaica Defence Force . Various African and South American countries received SA80s as part of wider military aid packages. Soon after being adopted for service, problems began to surface during troop trials held between 1986 and 1987. Components were found to be insufficiently robust,
3075-594: The SUSAT replaced with the Trijicon Advanced Combat Optical Gunsight (ACOG). In 2011, the Ministry of Defence began issuing ELCAN SpecterOS 4× Lightweight Day Sights (LDS) in an effort to replace ageing SUSAT units across the British Armed Forces, forming the first stage of the FIST infantry enhancement project. In order to mount the new sight, the weapon has been provided with an adapter to convert
L98 - Misplaced Pages Continue
3150-670: The XL73E3, developed from the XL65E4, was noted for the full-length receiver extension with the bipod under the muzzle now indicative of the type. Further development out of the initial so-called "Phase A" pre-production series led to the XL85 and XL86. While the XL85E1 and XL86E1 were ultimately adopted as the L85 and L86 respectively, a number of additional test models were produced. The XL85E2 and XL86E2 were designed to an alternate build standard with 12 components different from E1 variants, including parts of
3225-462: The bolt carrier. The family is built in a bullpup layout (the action is behind the trigger group), with a forward-mounted pistol grip . The main advantage of this type of arrangement is the overall compactness of the weapon, which can be achieved without compromising the barrel length, hence the overall length of the L85 rifle is shorter than a carbine, but the barrel length is that of an assault rifle. While left-handed conversion kits were trialled,
3300-655: The early 2000s by Heckler & Koch and remains in service as of 2024. The A3 variant was first issued in 2018 with several new improvements. The remainder of the SA80 family comprises the L86 Light Support Weapon, the short-barrelled L22 Carbine and the L98 Cadet rifle. The SA80 was the last in a long line of British weapons (including the Lee–Enfield family) to come from the Royal Small Arms Factory ,
3375-408: The effectiveness of the L85A1 and L86A1. This report criticised the acceptance of the weapon into service. Neither weapon had managed to pass the sand trials and both frequently jammed. The mechanism of both weapons needed to be well-lubricated as the weapon became prone to seizure if fired "dry", yet in a sandy environment the lubricated weapon became unreliable due to the lubricant attracting sand into
3450-452: The exception of the L98A2, the SA80 system is a selective fire gas-operated design that uses ignited powder gases bled through a port in the barrel to provide the weapon's automation. The rifle uses a short-stroke gas piston system located above the barrel, which is fed gas through a three-position adjustable gas regulator. The first gas setting is used for normal operation, the second ("Excess")
3525-644: The existing sight rail to the Picatinny standard, in keeping with the updated handguard. The FIST project has also seen upgrades to the existing Qioptiq CWS (4×) and Maxi-Kite (6×) night vision scopes, and the introduction of the FIST Thermal Sight, following operational experience with the VIPIR-2+ thermal weapon sight in Afghanistan. All of the new FIST weapon sights have the capacity to accept Shield's Close Quarter Battlesight reflex sight. SA80 weapons are fed from
3600-557: The first A2-style SA80 weapons were rushed into action in Afghanistan in December 2001, and all 200,000 were converted by February 2006. Three to four thousand weapons were converted per month. Despite the modifications, reports emerged that the L85A2 was still jamming; in reality, there were few jams and problems were much less serious than they were made out to be, since they stemmed from isolated cases of soldiers not cleaning their weapons correctly. The modified A2 variants are distinguished by
3675-539: The furniture and the safety plunger. Initially, rifles used by the Royal Marines , British Army infantry soldiers (and other soldiers with a dismounted close combat role) and the RAF Regiment are equipped with a SUSAT (Sight Unit Small Arms, Trilux) optical sight, with a fixed 4× magnification and an illuminated aiming pointer powered by a variable tritium light source (as of 2006 almost all British Army personnel deployed on operations have been issued SUSATs); this
3750-558: The future. The MLI project should see the weapon in service with the British military beyond 2025. Only the L85 rifle was announced as being upgraded; the L86 LSW would be withdrawn from use. The A3 received further upgrades in late 2020 following feedback from soldiers. These upgrades mainly included improvements to the ergonomics of the handguard and a switch from Heckler & Koch's HKey accessory attachment system to Magpul 's M-LOK . With
3825-505: The gas system, bolt, and magazine catch. Three series of variants were created for "Environmental User Trials". XL85E3 and XL86E3 variants were developed with 24 modified parts, most notably a plastic safety plunger. The E4's had 21 modified parts, no modification to the pistol grip, and an aluminium safety plunger, unlike the E3 variants. Lastly, the E5 variants had 9 modified parts in addition to those from
SECTION 50
#17328591062733900-460: The hell should we care if [the SA80] worked or not. All we wanted to do was see the last of the bloody things and leave." While production at the Nottingham facility was supposed to result in better-quality weapons owing to the use of newer manufacturing methods, few of the staff working there had any experience of firearms manufacture. Only 15 to 20 components were actually produced in-house, compared to
3975-565: The idea from reaching fruition. Technically, in the mid-1970s, the 4.85×49mm round was seen as superior to the then existing version of 5.56mm M193 round in use by the US (for the M16/M16A1 ) and by other forces. This was the expressed view of trials team members whilst demonstrating the XL64E5 prototype at the British Army School of Infantry at Warminster . Development of small-arms munitions have
4050-434: The link to point directly to the intended article. Retrieved from " https://en.wikipedia.org/w/index.php?title=L98&oldid=628422489 " Category : Letter–number combination disambiguation pages Hidden categories: Short description is different from Wikidata All article disambiguation pages All disambiguation pages SA80#L98 Cadet General Purpose Rifles The SA80 (Small Arms for
4125-524: The location and stiffness of the fire selector switch. During Operation Palliser and other intervention operations in Sierra Leone, it was discovered that the version of the safety plunger used for production weapons was made from cheap injection-moulded plastic that swelled when wet, potentially rendering weapons inoperative if they had been left on 'safe'. The SA80 initially gained a poor reputation amongst British soldiers as being unreliable and fragile,
4200-452: The magazine when loaded with British-issue ammunition meant that it was not adopted. In British Armed Forces use, the L85 Rifle is issued with the socket-type L3A1 Bayonet, which has a hollow handle that fits onto the muzzle. The blade is offset to the side of the handle to allow the rifle to be fired while the bayonet is fitted. It is shaped to produce good penetration when thrust and to part
4275-501: The moving parts. The LANDSET report identified in excess of 50 faults, most notably the magazine release catch, which could easily be caught on clothing and accidentally release the magazine; the plastic safety plunger which became brittle in cold climates; and firing pins that were not up to repeated use, and prone to fracture if used in automatic fire mode. The report concluded that "It is, however, quite clear that infantrymen did not have CONFIDENCE in their personal weapon. Most expected
4350-413: The national arms development and production facility at Enfield Lock , before its weapons factory was closed down in 1988. The idea dates back to the late 1940s, when an ambitious programme to develop a new cartridge and new class of rifle was launched in the United Kingdom based on combat experience drawn from World War II. Two 7mm (.280 in) prototypes were built in a bullpup configuration, designated
4425-403: The opposite was true of the L86A1. Specific complaints included: the poor quality plastic furniture fell apart and the gun was damaged easily; the magazine release catch was easily knocked accidentally and dropped the magazine; the catch on the top cover over the gas mechanism was too weak and constantly popped open, so it had to be taped down; only 26–28 rounds could be loaded in a magazine because
4500-517: The rear. To release the bolt, the user has to press a black button on the left side of the rifle, near the fire selector. The SA80 barrel features a flash eliminator which serves as a mounting base for attaching a blank firing attachment ; it also allows for the use of rifle grenades or a bayonet with the rifle variant. The weapon's receiver is made from stamped sheet steel , reinforced with welded and riveted machined steel inserts. Synthetic materials such as nylon were used to fabricate
4575-414: The right hand side of the rifle downwards, reducing the impediments of the cocking handle and the ejection port; the MOD also maintains that left-handed soldiers are capable of accurately firing the weapon from the right shoulder. The SA80 family is hammer-fired and has a trigger mechanism with a fire-control selector that enables semi-automatic/repetition and fully automatic fire (the fire selector lever
SECTION 60
#17328591062734650-447: The same term This disambiguation page lists articles associated with the same title formed as a letter–number combination. If an internal link led you here, you may wish to change the link to point directly to the intended article. Retrieved from " https://en.wikipedia.org/w/index.php?title=L64&oldid=932955015 " Category : Letter–number combination disambiguation pages Hidden categories: Short description
4725-459: The springs were weak, something that was also mentioned in training manuals, at least with regard to earlier Colt -produced magazines, and it had to be kept very clean and the lips checked for dents. The magazine was made from aluminium and would deform if grasped too tightly. During firing, this could choke the flow of rounds and result in a jam; the LSW had a small magazine capacity for its role and overheated after 120–150 rounds fired in bursts;
4800-456: The upgrade to A2, including a requirement to forward assist with the left hand to ensure the bolt is properly closed and locked; without this there is increased risk of a jam. A new cleaning kit was issued with major enhancements designed for simpler and more effective use while on operations. A further upgrade including the provision of Advanced Combat Optical Gunsights (ACOGs), a Daniel Defense -designed Picatinny rail (RIS) handguard for
4875-447: The various design changes requested, including adapting the rifle for use with the heavier Belgian SS109 version of the 5.56×45mm round and improving reliability, the weapon system was accepted into service with the British Armed Forces in 1985 as the SA80. The SA80 family originally consisted of the L85A1 Rifle, the L86A1 Light Support Weapon (LSW), and L98A1 Cadet GP Rifle. The first weapons were issued in October 1985. The SA80 family
4950-444: The weapon as finally issued must be used exclusively right-handed since the ejection port and cocking handle (which reciprocates during firing) are on the right side of the receiver, making aimed fire from the left shoulder difficult. This can also give rise to a tactical disadvantage when firing around the left side of cover, where the shooter must expose the majority of their body. However left shoulder firing can be achieved by tilting
5025-449: The weapon when firing bursts. The weapon is otherwise identical to the L85 version on which it is based, and the same magazines and sighting systems are used. In addition to British Armed Forces use, the LSW was adopted by MOD-sponsored cadet organisations. The increased barrel length, bipod and the optical performance of the SUSAT give the weapon excellent accuracy, increased muzzle velocity and greater effective range. From its inception,
5100-408: The weapons were difficult to strip and reassemble, with the gas plug easily jamming in place and requiring an armorer to remove; the firing pin was too narrow and would snap; the back of the trigger surface was flat which with snow or dirt accumulating behind it would prevent the trigger from pulling back all the way and firing the gun; and ergonomic issues related to the safety catch, cocking lever, and
5175-541: The world". Armed Forces trials indicated extremely good reliability over a range of climates for various operational scenarios, though with a decline in reliability in hot, and especially hot and dry conditions. The L85A2 achieved an average reliability rate of 25,200 mean rounds between failure , and the L86A2 achieved 12,897 mean rounds between failures. Both weapons have higher reliability rates in cold/dry, temperate, and hot/wet conditions, but lower rates in hot/dry environments. The minimum expected life of A2 components
5250-413: Was considered too expensive. As a result, a more extensive modification programme was executed. In 2000, a team from Heckler & Koch, led by Ernst Mauch, was contracted to upgrade the SA80 family of weapons. At that time Heckler & Koch were owned by BAE Systems. 200,000 SA80s were re-manufactured for £400 each, producing the A2 variant. Changes focused primarily on improving reliability and include
5325-405: Was designed and produced by the Royal Small Arms Factory at Enfield Lock . In 1988, production of the rifle was transferred to the Nottingham Small Arms Facility owned by Royal Ordnance (later British Aerospace , Royal Ordnance; now BAE Systems ), the site was previously known as ROF Nottingham . It was envisaged that the family would replace the L1A1 SLR, the L2A3 (Sterling) submachine gun ,
5400-416: Was introduced from 2011, featuring a lower weight of 130 grams (4.6 oz) compared to the steel magazine's 249 grams (8.8 oz), a detachable dust cover, and a clear window in the magazine body that allows easy monitoring of how much ammunition remains in the magazine. The Beta C-Mag was trialled in an attempt to improve the L86's limited ability to lay down sustained fire, but reliability problems with
5475-511: Was leaked to the press, at which point the Ministry of Defence claimed that it was fake; while it was later admitted that the report was a genuine document, the MOD continued to downplay its significance, and only seven of the 50 faults identified were addressed by subsequent modifications, meaning that complaints over reliability in service continued. The MOD finally began to take the SA80 family's issues seriously in 1992, but procuring entirely new weapons
5550-529: Was only in relation to weapons such as the Sten submachine gun that had relatively loose tolerances. The tighter tolerances required by the SA80 soon led to production delays and high wastage levels. There were also issues with regard to working practices and employee attitudes at the Enfield site which were exacerbated by its closure in 1988 and resulting redundancies. One worker was recorded as saying that "Having been shafted by BAE and our own management, we thought why
5625-472: Was regarded as probable at the time that the argument for the 5.56mm standard within NATO had more to do with the economics involved. Over the lifetime of a small-arms weapon type, far more money is spent on the munitions than the weapons themselves. If the 5.56mm supporters had lost the argument in favour of a British 4.85mm round, the economic impact would have been very large, and political pressure undoubtedly played
#272727