Misplaced Pages

#26973

60-596: The Healdsburg Memorial Bridge is a Pennsylvania (Petit) truss bridge. This once-popular design, named for the Pennsylvania Railroad , has since fallen out of favor. The Healdsburg bridge is one of only two bridges of this design still carrying vehicle traffic in California, and one of only 13 in the United States. The bridge has two truss spans, each with ten panels. The entire bridge is 438 feet (134 m) long;

120-466: A Parker truss or Pratt truss than a true arch . In the Brown truss all vertical elements are under tension, with exception of the end posts. This type of truss is particularly suited for timber structures that use iron rods as tension members. See Lenticular truss below. This combines an arch with a truss to form a structure both strong and rigid. Most trusses have the lower chord under tension and

180-611: A covered bridge to protect the structure. In 1820, a simple form of truss, Town's lattice truss , was patented, and had the advantage of requiring neither high labor skills nor much metal. Few iron truss bridges were built in the United States before 1850. Truss bridges became a common type of bridge built from the 1870s through the 1930s. Examples of these bridges still remain across the US, but their numbers are dropping rapidly as they are demolished and replaced with new structures. As metal slowly started to replace timber, wrought iron bridges in

240-416: A truss allows the analysis of its structure using a few assumptions and the application of Newton's laws of motion according to the branch of physics known as statics . For purposes of analysis, trusses are assumed to be pin jointed where the straight components meet, meaning that taken alone, every joint on the structure is functionally considered to be a flexible joint as opposed to a rigid joint with

300-483: A truss , a structure of connected elements, usually forming triangular units. The connected elements, typically straight, may be stressed from tension , compression , or sometimes both in response to dynamic loads. There are several types of truss bridges, including some with simple designs that were among the first bridges designed in the 19th and early 20th centuries. A truss bridge is economical to construct primarily because it uses materials efficiently. The nature of

360-544: A Parker truss vary from near vertical in the center of the span to diagonal near each end, similar to a Warren truss. George H. Pegram , while the chief engineer of Edge Moor Iron Company in Wilmington, Delaware , patented this truss design in 1885. The Pegram truss consists of a Parker type design with the vertical posts leaning towards the center at an angle between 60 and 75°. The variable post angle and constant chord length allowed steel in existing bridges to be recycled into

420-594: A continuous truss functions as a single rigid structure over multiple supports. This means that the live load on one span is partially supported by the other spans, and consequently it is possible to use less material in the truss. Continuous truss bridges were not very common before the mid-20th century because they are statically indeterminate , which makes them difficult to design without the use of computers . A multi-span truss bridge may also be constructed using cantilever spans, which are supported at only one end rather than both ends like other types of trusses. Unlike

480-516: A continuous truss, a cantilever truss does not need to be connected rigidly, or indeed at all, at the center. Many cantilever bridges, like the Quebec Bridge shown below, have two cantilever spans supporting a simple truss in the center. The bridge would remain standing if the simple truss section were removed. Bridges are the most widely known examples of truss use. There are many types, some of them dating back hundreds of years. Below are some of

540-435: A conventional truss into place or by building it in place using a "traveling support". In another method of construction, one outboard half of each balanced truss is built upon temporary falsework. When the outboard halves are completed and anchored the inboard halves may then be constructed and the center section completed as described above. The Fink truss was designed by Albert Fink of Germany in 1854. This type of bridge

600-590: A lack of durability, and gave way to the Pratt truss design, which was stronger. Again, the bridge companies marketed their designs, with the Wrought Iron Bridge Company in the lead. As the 1880s and 1890s progressed, steel began to replace wrought iron as the preferred material. Other truss designs were used during this time, including the camel-back. By the 1910s, many states developed standard plan truss bridges, including steel Warren pony truss bridges. In

660-413: A lesser economy of materials and the difficulty of design before the advent of computers, this truss is rarely used in bridges outside Belgium. The form is more commonly employed in building structures where large shear walls or diagonal elements would interfere with the building's aesthetics or functionality. The first such bridge was built in steel at Avelgem , Belgium in 1902, following development of

SECTION 10

#1732852154027

720-477: A lower chord (functioning as a suspension cable) that curves down and then up to meet at the same end points. Where the arches extend above and below the roadbed, it is called a lenticular pony truss bridge . The Pauli truss bridge is a specific variant of the lenticular truss, but the terms are not interchangeable. One type of lenticular truss consists of arcuate upper compression chords and lower eyebar chain tension links. Brunel 's Royal Albert Bridge over

780-704: A new span using the Pegram truss design. This design also facilitated reassembly and permitted a bridge to be adjusted to fit different span lengths. There are twelve known remaining Pegram span bridges in the United States with seven in Idaho , two in Kansas , and one each in California , Washington , and Utah . The Pennsylvania (Petit) truss is a variation on the Pratt truss . The Pratt truss includes braced diagonal members in all panels;

840-445: A strike; before the collapse, similar incidents had been common and had necessitated frequent repairs. Truss bridges consisting of more than one span may be either a continuous truss or a series of simple trusses. In the simple truss design, each span is supported only at the ends and is fully independent of any adjacent spans. Each span must fully support the weight of any vehicles traveling over it (the live load ). In contrast,

900-532: A variant of the lenticular truss, "with the top chord carefully shaped so that it has a constant force along the entire length of the truss." It is named after Friedrich Augustus von Pauli  [ de ] , whose 1857 railway bridge (the Großhesseloher Brücke  [ de ] ) spanned the Isar near Munich . ( See also Grosshesselohe Isartal station .) The term Pauli truss is not interchangeable with

960-423: Is a bridge employing a Vierendeel truss , named after Arthur Vierendeel , a Belgian engineer who proposed this new bridge girder-type without diagonals in 1896. Such trusses are made up of rectangular rather than triangular frames, as are common in bridges using pin–joints . Because of the lack of diagonal members, Vierendeel trusses employ moment joints to resist substantial bending forces. Owing to

1020-677: Is a Pratt truss design with a polygonal upper chord. A "camelback" is a subset of the Parker type, where the upper chord consists of exactly five segments. An example of a Parker truss is the Traffic Bridge in Saskatoon , Canada. An example of a camelback truss is the Woolsey Bridge near Woolsey, Arkansas . Designed and patented in 1872 by Reuben Partridge , after local bridge designs proved ineffective against road traffic and heavy rains. It became

1080-507: Is a hybrid between a Warren truss and a double-intersection Pratt truss. Invented in 1863 by Simeon S. Post, it is occasionally referred to as a Post patent truss although he never received a patent for it. The Ponakin Bridge and the Bell Ford Bridge are two examples of this truss. A Pratt truss includes vertical members and diagonals that slope down towards the center, the opposite of

1140-798: Is named after the K formed in each panel by the vertical member and two oblique members. Examples include the Südbrücke rail bridge over the River Rhine, Mainz, Germany, the bridge on I-895 (Baltimore Harbor Tunnel Thruway) in Baltimore, Maryland, the Long–Allen Bridge in Morgan City, Louisiana (Morgan City Bridge) with three 600-foot-long spans, and the Wax Lake Outlet bridge in Calumet, Louisiana One of

1200-671: Is practical for use with spans up to 250 feet (76 m) and was a common configuration for railroad bridges as truss bridges moved from wood to metal. They are statically determinate bridges, which lend themselves well to long spans. They were common in the United States between 1844 and the early 20th century. Examples of Pratt truss bridges are the Governor's Bridge in Maryland ; the Hayden RR Bridge in Springfield, Oregon , built in 1882;

1260-513: Is the Victoria Bridge on Prince Street, Picton, New South Wales . Also constructed of ironbark, the bridge is still in use today for pedestrian and light traffic. The Bailey truss was designed by the British in 1940–1941 for military uses during World War II. A short selection of prefabricated modular components could be easily and speedily combined on land in various configurations to adapt to

SECTION 20

#1732852154027

1320-604: Is used in the teaching of statics, by the building of model bridges from spaghetti . Spaghetti is brittle and although it can carry a modest tension force, it breaks easily if bent. A model spaghetti bridge thus demonstrates the use of a truss structure to produce a usefully strong complete structure from individually weak elements. In the United States , because wood was in abundance, early truss bridges would typically use carefully fitted timbers for members taking compression and iron rods for tension members , usually constructed as

1380-597: The Dearborn River High Bridge near Augusta, Montana, built in 1897; and the Fair Oaks Bridge in Fair Oaks, California , built 1907–09. The Scenic Bridge near Tarkio, Montana , is an example of a Pratt deck truss bridge, where the roadway is on top of the truss. The queenpost truss , sometimes called "queen post" or queenspost, is similar to a king post truss in that the outer supports are angled towards

1440-1224: The Fort Wayne Street Bridge in Goshen, Indiana , the Schell Bridge in Northfield, Massachusetts , the Inclined Plane Bridge in Johnstown, Pennsylvania , the Easton–Phillipsburg Toll Bridge in Easton, Pennsylvania , the Connecticut River Bridge in Brattleboro, Vermont , the Metropolis Bridge in Metropolis, Illinois , and the Healdsburg Memorial Bridge in Healdsburg, California . A Post truss

1500-491: The Howe truss . The interior diagonals are under tension under balanced loading and vertical elements under compression. If pure tension elements (such as eyebars ) are used in the diagonals, then crossing elements may be needed near the center to accept concentrated live loads as they traverse the span. It can be subdivided, creating Y- and K-shaped patterns. The Pratt truss was invented in 1844 by Thomas and Caleb Pratt. This truss

1560-475: The River Tamar between Devon and Cornwall uses a single tubular upper chord. As the horizontal tension and compression forces are balanced these horizontal forces are not transferred to the supporting pylons (as is the case with most arch types). This in turn enables the truss to be fabricated on the ground and then to be raised by jacking as supporting masonry pylons are constructed. This truss has been used in

1620-668: The Verdugo Flood Control Project , the first project of the United States Army Corps of Engineers after passage of the Flood Control Act of 1936 . The double-deck cable-stayed Kap Shui Mun Bridge in Hong Kong uses a Vierendeel truss. Opened in 1997, the lower deck carries both rail and traffic, with the lack of diagonal members in the cross section allowing vehicles to drive through the openings provided by

1680-412: The 1920s and 1930s, Pennsylvania and several states continued to build steel truss bridges, using massive steel through-truss bridges for long spans. Other states, such as Michigan , used standard plan concrete girder and beam bridges, and only a limited number of truss bridges were built. The truss may carry its roadbed on top, in the middle, or at the bottom of the truss. Bridges with the roadbed at

1740-593: The Pennsylvania truss adds to this design half-length struts or ties in the top, bottom, or both parts of the panels. It is named after the Pennsylvania Railroad , which pioneered this design. It was once used for hundreds of bridges in the United States, but fell out of favor in the 1930s and very few examples of this design remain. Examples of this truss type include the Lower Trenton Bridge in Trenton, New Jersey ,

1800-526: The US started being built on a large scale in the 1870s. Bowstring truss bridges were a common truss design during this time, with their arched top chords. Companies like the Massillon Bridge Company of Massillon, Ohio , and the King Bridge Company of Cleveland , became well-known, as they marketed their designs to cities and townships. The bowstring truss design fell out of favor due to

1860-454: The balance between labor, machinery, and material costs has certain favorable proportions. The inclusion of the elements shown is largely an engineering decision based upon economics, being a balance between the costs of raw materials, off-site fabrication, component transportation, on-site erection, the availability of machinery, and the cost of labor. In other cases, the appearance of the structure may take on greater importance and so influence

Healdsburg Memorial Bridge - Misplaced Pages Continue

1920-425: The bridge illustrated in the infobox at the top, vertical members are in tension, lower horizontal members in tension, shear , and bending, outer diagonal and top members are in compression, while the inner diagonals are in tension. The central vertical member stabilizes the upper compression member, preventing it from buckling . If the top member is sufficiently stiff then this vertical element may be eliminated. If

1980-546: The bridge lies in Healdsburg Veterans Memorial Beach Park; another truss bridge carrying the former Northwestern Pacific Railroad crosses the river nearby to the north and also ends within the same park. The point on the river now used by the bridge was used as a ford by settlers to Sonoma County since the 1850s. The memorial bridge was built in 1921 by the American Bridge Company to carry

2040-473: The center of the structure. The primary difference is the horizontal extension at the center which relies on beam action to provide mechanical stability. This truss style is only suitable for relatively short spans. The Smith truss , patented by Robert W Smith on July 16, 1867, has mostly diagonal criss-crossed supports. Smith's company used many variations of this pattern in the wooden covered bridges it built. Vierendeel bridge A Vierendeel bridge

2100-707: The center, the opposite of the Pratt truss . In contrast to the Pratt truss, the diagonal web members are in compression and the vertical web members are in tension. Few of these bridges remain standing. Examples include Jay Bridge in Jay, New York ; McConnell's Mill Covered Bridge in Slippery Rock Township, Lawrence County, Pennsylvania ; Sandy Creek Covered Bridge in Jefferson County, Missouri ; and Westham Island Bridge in Delta, British Columbia , Canada. The K-truss

2160-408: The city providing funds for ongoing maintenance of the bridge. The retrofitting and restoration was completed in 2015. The work involved construction of a new mid-river pier, installation of isolation bearings, reinforcement of truss members, and replacement of the deck. Truss bridge#Pennsylvania (Petit) truss A truss bridge is a bridge whose load-bearing superstructure is composed of

2220-579: The community, no action was taken. In 2000 the city again made plans for the bridge, involving a seismic retrofit. In 2007, errors in the 1979 report were discovered, and a new report in 2008 showed that the bridge remained structurally sound. It was officially listed on the National Register of Historic Places in April 2011, and in December 2011, state and federal funding for restoration was approved, contingent on

2280-414: The compression members and to control deflection. It is mainly used for rail bridges, showing off a simple and very strong design. In the Pratt truss the intersection of the verticals and the lower horizontal tension members are used to anchor the supports for the short-span girders under the tracks (among other things). With the Baltimore truss, there are almost twice as many points for this to happen because

2340-576: The construction of a stadium, with the upper chords of parallel trusses supporting a roof that may be rolled back. The Smithfield Street Bridge in Pittsburgh, Pennsylvania , is another example of this type. An example of a lenticular pony truss bridge that uses regular spans of iron is the Turn-of-River Bridge designed and manufactured by the Berlin Iron Bridge Co. The Pauli truss is

2400-429: The design decisions beyond mere matters of economics. Modern materials such as prestressed concrete and fabrication methods, such as automated welding , and the changing price of steel relative to that of labor have significantly influenced the design of modern bridges. A pure truss can be represented as a pin-jointed structure, one where the only forces on the truss members are tension or compression, not bending. This

2460-475: The earliest examples is the Old Blenheim Bridge , which with a span of 210 feet (64 m) and a total length of 232 feet (71 m) long was the second-longest covered bridge in the United States, until its destruction from flooding in 2011. The Busching bridge, often erroneously used as an example of a Long truss, is an example of a Howe truss, as the verticals are metal rods. A Parker truss bridge

Healdsburg Memorial Bridge - Misplaced Pages Continue

2520-462: The historic Redwood Highway; when built it was the only steel bridge across the Russian River. At that time an annual temporary dam built downriver from the bridge created a swimming area; the same part of the river still remains popular for swimming. When U.S. Route 101 was built, on a new alignment crossing the river farther to the west, most of the traffic formerly carried by the memorial bridge

2580-463: The longer of its two spans is 198 feet (60 m) long. Its deck is 19.4 feet (5.9 m) wide, with a vertical clearance of 14.9 feet (4.5 m); because its narrow deck does not meet modern safety standards, it is classified as functionally obsolete. The bridge carries 7,400 vehicles per day on Healdsburg Avenue (a local road in Healdsburg) as well as pedestrian and bicycle traffic. The east end of

2640-482: The lower chord (a horizontal member of a truss) is sufficiently resistant to bending and shear, the outer vertical elements may be eliminated, but with additional strength added to other members in compensation. The ability to distribute the forces in various ways has led to a large variety of truss bridge types. Some types may be more advantageous when the wood is employed for compression elements while other types may be easier to erect in particular site conditions, or when

2700-504: The more common designs. The Allan truss , designed by Percy Allan , is partly based on the Howe truss . The first Allan truss was completed on 13 August 1894 over Glennies Creek at Camberwell, New South Wales and the last Allan truss bridge was built over Mill Creek near Wisemans Ferry in 1929. Completed in March 1895, the Tharwa Bridge located at Tharwa, Australian Capital Territory ,

2760-412: The needs at the site and allow rapid deployment of completed trusses. In the image, note the use of pairs of doubled trusses to adapt to the span and load requirements. In other applications the trusses may be stacked vertically, and doubled as necessary. The Baltimore truss is a subclass of the Pratt truss. A Baltimore truss has additional bracing in the lower section of the truss to prevent buckling in

2820-474: The roadbed but are not connected, a pony truss or half-through truss. Sometimes both the upper and lower chords support roadbeds, forming a double-decked truss . This can be used to separate rail from road traffic or to separate the two directions of road traffic. Since through truss bridges have supports located over the bridge deck, they are susceptible to being hit by overheight loads when used on highways. The I-5 Skagit River bridge collapsed after such

2880-559: The short verticals will also be used to anchor the supports. Thus the short-span girders can be made lighter because their span is shorter. A good example of the Baltimore truss is the Amtrak Old Saybrook – Old Lyme Bridge in Connecticut , United States. The Bollman Truss Railroad Bridge at Savage, Maryland , United States is the only surviving example of a revolutionary design in the history of American bridge engineering. The type

2940-451: The simplest truss styles to implement, the king post consists of two angled supports leaning into a common vertical support. This type of bridge uses a substantial number of lightweight elements, easing the task of construction. Truss elements are usually of wood, iron, or steel. A lenticular truss bridge includes a lens-shape truss, with trusses between an upper chord functioning as an arch that curves up and then down to end points, and

3000-450: The standard for covered bridges built in central Ohio in the late 1800s and early 1900s. The Pegram truss is a hybrid between the Warren and Parker trusses where the upper chords are all of equal length and the lower chords are longer than the corresponding upper chord. Because of the difference in upper and lower chord length, each panel is not square. The members which would be vertical in

3060-414: The strength to maintain its shape, and the resulting shape and strength of the structure are only maintained by the interlocking of the components. This assumption means that members of the truss (chords, verticals, and diagonals) will act only in tension or compression. A more complex analysis is required where rigid joints impose significant bending loads upon the elements, as in a Vierendeel truss . In

SECTION 50

#1732852154027

3120-472: The term lenticular truss and, according to Thomas Boothby, the casual use of the term has clouded the literature. The Long truss was designed by Stephen H. Long in 1830. The design resembles a Howe truss , but is entirely made of wood instead of a combination of wood and metal. The longest surviving example is the Eldean Covered Bridge north of Troy, Ohio , spanning 224 feet (68 m). One of

3180-525: The top or the bottom are the most common as this allows both the top and bottom to be stiffened, forming a box truss . When the roadbed is atop the truss, it is a deck truss; an example of this was the I-35W Mississippi River bridge . When the truss members are both above and below the roadbed it is called a through truss; an example of this is the Pulaski Skyway , and where the sides extend above

3240-587: The truss form and a method to calculate its strength in 1896 by Arthur Vierendeel. There are many more examples in Belgium, including some built in concrete, mostly designed by Vierendeel's many students from his long career as professor in civil engineering . The city of Glendale, California has three Vierendeel truss bridges: the Geneva Street, Kenilworth Avenue, and Glenoaks Boulevard bridges, all two-lane bridges spanning 95 feet. They were built in 1937 as part of

3300-428: The upper chord under compression. In a cantilever truss the situation is reversed, at least over a portion of the span. The typical cantilever truss bridge is a "balanced cantilever", which enables the construction to proceed outward from a central vertical spar in each direction. Usually these are built in pairs until the outer sections may be anchored to footings. A central gap, if present, can then be filled by lifting

3360-414: Was also easy to assemble. Wells Creek Bollman Bridge is the only other bridge designed by Wendel Bollman still in existence, but it is a Warren truss configuration. The bowstring truss bridge was patented in 1841 by Squire Whipple . While similar in appearance to a tied-arch bridge , a bowstring truss has diagonal load-bearing members: these diagonals result in a structure that more closely matches

3420-553: Was diverted. The original bridge design included decorative lights, which were removed in the 1950s. A structural report in 1979 showed the bridge as being near collapse. The land containing the bridge was annexed by Healdsburg in 1980. In 1985, the bridge was declared eligible for the National Register of Historic Places , despite which the Healdsburg city government began planning to replace it in 1990. After negative reaction from

3480-405: Was named after its inventor, Wendel Bollman , a self-educated Baltimore engineer. It was the first successful all-metal bridge design (patented in 1852) to be adopted and consistently used on a railroad. The design employs wrought iron tension members and cast iron compression members. The use of multiple independent tension elements reduces the likelihood of catastrophic failure. The structure

3540-659: Was popular with the Baltimore and Ohio Railroad . The Appomattox High Bridge on the Norfolk and Western Railway included 21 Fink deck truss spans from 1869 until their replacement in 1886. There are also inverted Fink truss bridges such as the Moody Pedestrian Bridge in Austin, Texas. The Howe truss , patented in 1840 by Massachusetts millwright William Howe , includes vertical members and diagonals that slope up towards

3600-814: Was the second Allan truss bridge to be built, the oldest surviving bridge in the Australian Capital Territory and the oldest, longest continuously used Allan truss bridge. Completed in November 1895, the Hampden Bridge in Wagga Wagga, New South Wales , Australia, the first of the Allan truss bridges with overhead bracing, was originally designed as a steel bridge but was constructed with timber to reduce cost. In his design, Allan used Australian ironbark for its strength. A similar bridge also designed by Percy Allen

#26973