150-576: The Fender Stratocaster , colloquially known as the Strat , is a model of electric guitar designed between 1952 and 1954 by Leo Fender , Bill Carson , George Fullerton , and Freddie Tavares . The Fender Musical Instruments Corporation has continuously manufactured the Stratocaster since 1954. It is a double- cutaway guitar, with an extended top "horn" shape for balance. "Stratocaster" and "Strat" are trademark terms belonging to Fender. Guitars that duplicate
300-466: A monaural signal. Many guitars with active electronics use a jack with an extra contact normally used for stereo . These guitars use the extra contact to break the ground connection to the on-board battery to preserve battery life when the guitar is unplugged. These guitars require a mono plug to close the internal switch and connect the battery to ground. Standard guitar cables use a high-impedance 1 ⁄ 4 inch (6.35 mm) mono plug. These have
450-400: A vibrato embellishment. A plastic pickguard on some guitars protects the body from scratches or covers the control cavity, which holds most of the wiring. The degree to which the choice of woods and other materials in the solid-guitar body (3) affects the sonic character of the amplified signal is disputed. Many believe it is highly significant, while others think the difference between woods
600-450: A whammy bar , vibrato bar , or tremolo arm . The lever enables the player to quickly and temporarily vary the tension and sometimes length of the strings, changing the pitch to create a vibrato , portamento , or pitch bend effect. Instruments without a vibrato have other bridge and tailpiece systems . The pitch-bending effects have become an important part of many styles, allowing creation of sounds that could not be played without
750-510: A "whang bar". Most vibrato systems for guitar are based on one of four basic designs: Many other designs exist in smaller numbers, notably several original designs marketed by Gibson under the Vibrola name, which they also used for some licensed Bigsby units. The world's first patented mechanical vibrato unit was created and designed by Doc Kauffman . The initial patent was filed in August 1929 and
900-539: A 12" radius. Fender has produced various 'deluxe' modern American Stratocasters with special features. The Strat Plus was produced from 1987 to 1999 and was equipped with Lace Sensor pickups, a roller nut, locking tuners, a TBX tone control and a Hipshot tremsetter. The Strat Plus Deluxe was introduced in 1989 with pickup and tremolo variations. The Strat Ultra was introduced in 1990, again with pickup variations, and also with an ebony fingerboard. The Fender Custom Shop produced an entry level, team built Stratocaster that
1050-483: A Bigsby option. Since the early 1960s, Gibson have marketed a number of vibrato system designs under the name " Vibrola ". Vibrola tailpieces include a licensed version of the Bigsby vibrato tailpiece , earlier version of Maestro Vibrola (or Epiphone Tremotone ) using roller bridge ( U.S. patent 3,124,991 filed in 1961, issued in 1964), and several in-house Gibson designs. The Gibson designs did not have
1200-525: A United States patent for an Electrical Stringed Musical Instrument and the patent was later issued in 1937. By the time it was patented, other manufacturers were already making their own electric guitar designs. Early electric guitar manufacturers include Rickenbacker in 1932; Dobro in 1933; National, AudioVox and Volu-tone in 1934; Vega , Epiphone (Electrophone and Electar), and Gibson in 1935 and many others by 1936. By early-mid 1935, Electro String Instrument Corporation had achieved success with
1350-590: A built-in system to electrically amplify their output without altering their tone as an alternative to using a separate microphone. The system may consist of piezoelectric pickups mounted under the bridge, or a low-mass microphone (usually a condenser mic) inside the body of the guitar that converts the vibrations in the body into electronic signals. Combinations of these types of pickups may be used, with an integral mixer/preamp/graphic equalizer. Such instruments are called electric acoustic guitars . They are regarded as acoustic guitars rather than electric guitars because
1500-453: A distinctive headstock with six tuning pegs mounted inline along a single side; the fingerboard may be maple or another wood, e.g., rosewood , and has at least twenty-one frets . The Stratocaster's body is front- routed for electronics, which are mounted in a plastic pickguard . Most Stratocasters have three single-coil pickups , a pickup selector switch , one volume control and two tone controls. Bridges generally come in two designs:
1650-507: A fixed bridge or a spring-loaded hinged bridge , which lets players "bend" the pitch of notes or chords up or down, or perform vibrato effects. The sound of an electric guitar can be modified by new playing techniques such as string bending , tapping , and hammering-on , using audio feedback , or slide guitar playing. There are several types of electric guitar. Early forms were hollow-body semi-acoustic guitars , while solid body guitars developed later. String configurations include
SECTION 10
#17330855256981800-413: A fixed-tailpiece guitar. Since the regular appearance of mechanical vibrato systems in the 1950s, many guitarists have used them—from Chet Atkins to Duane Eddy and the surf music of The Ventures , The Shadows , and Dick Dale . In the 1960s and 1970s, Jimi Hendrix , Jeff Beck , David Gilmour , Ritchie Blackmore , Jimmy Page , and Frank Zappa used vibrato arms for more pronounced effects. In
1950-576: A folding neck called the "Foldaxe" was designed and built for Chet Atkins by Roger C. Field . Steinberger guitars developed a line of exotic, carbon fiber instruments without headstocks, with tuning done on the bridge instead. Fingerboards vary as much as necks. The fingerboard surface usually has a cross-sectional radius that is optimized to accommodate finger movement for different playing techniques. Fingerboard radius typically ranges from nearly flat (a very large radius) to radically arched (a small radius). The vintage Fender Telecaster , for example, has
2100-428: A guitar amplifier and speaker. When an electric guitar is played, string movement produces a signal by generating (i.e., inducing ) a small electric current in the magnetic pickups, which are magnets wound with coils of very fine wire. The signal passes through the tone and volume circuits to the output jack, and through a cable to an amplifier . The current induced is proportional to such factors as string density and
2250-519: A hard, polymerized finish. Strings vibrating in the magnetic field of the pickups (3.1, 3.2) produce an electric current in the pickup winding that passes through the tone and volume controls (3.8) to the output jack. Some guitars have piezo pickups, in addition to or instead of magnetic pickups. Some guitars have a fixed bridge (3.4). Others have a spring-loaded hinged bridge called a vibrato bar , tremolo bar , or whammy bar , which lets players bend notes or chords up or down in pitch or perform
2400-658: A neck-through design is difficult or even impossible to repair, depending on the damage. Historically, the bolt-on style has been more popular for ease of installation and adjustment. Since bolt-on necks can be easily removed, there is an after-market in replacement bolt-on necks from companies such as Warmoth and Mighty Mite. Some instruments—notably most Gibson models—continue to use set-in glued necks. Neck-through bodies are somewhat more common in bass guitars. Materials for necks are selected for dimensional stability and rigidity, and some allege that they influence tone. Hardwoods are preferred, with maple , mahogany , and ash topping
2550-438: A pitch bend. Fender's design is 'synchronized' in the way that the bridge saddles and string ends move together as one rigid unit, mostly eliminating sliding between string and saddle. The unit attaches to the guitar's body with six steel wood screws. So the bridge can pivot smoothly about the screws, the upper portion of each one is unthreaded, they are not tightened all the way, and they pass through slightly oversized holes in
2700-434: A rhythm guitarist and a lead guitarist. Many experiments with electrically amplifying the vibrations of a string instrument were made dating back to the early part of the 20th century. Patents from the 1910s show telephone transmitters were adapted and placed inside violins and banjos to amplify the sound. Hobbyists in the 1920s used carbon button microphones attached to the bridge ; however, these detected vibrations from
2850-519: A rosewood fretboard, and maple fretboards would not be re-introduced in large numbers until 1970. In 1960, the available custom colors were standardized with a paint chip chart, many of which were Duco automobile lacquer colors from DuPont available at an additional 5% cost. Inter-departmental DuPont support research provided a flexible basecoat for their wood applications. A single-ply, eight-screw hole white pickguard (changed to an 11-hole three-ply in late 1959) held all electronic components except
3000-423: A semi-acoustic tone (see below) or both. Semi-acoustic guitars have a hollow body similar to an acoustic guitar and electromagnetic pickups mounted directly into the body. They work in a similar way to solid-body electric guitars except that because the hollow body also vibrates, the pickups convert a combination of string and body vibration into an electrical signal. Many models, known as semi-hollow bodies, have
3150-421: A simple relation exists between the length to the fret and the string length behind the bridge (for instance 48:12 = 4:1). At those positions, a high overtone rises in volume. This becomes clearer with an over-driven guitar sound. The overtone might sound odd, but it still has a harmonic relation to the note, so is not out of tune related to the open string. For staccato playing, it can be annoying. Muting
SECTION 20
#17330855256983300-418: A single block of wood, semi-acoustic guitar bodies are made from multiple pieces of wood in an archtop form, a method of construction different from the typical steel string acoustic guitar . The top is formed from a moderately thick piece of wood which is then carved into a thin outward-curving shape, whereas conventional acoustic guitars have a thin, flat top. Some steel-string acoustic guitars include
3450-570: A solid block running through the middle of the soundbox designed to reduce acoustic feedback. They do not provide enough acoustic volume for live performance, but they can be used unplugged for quiet practice. Semi-acoustic guitars are noted for being able to provide a sweet, plaintive, or funky tone. They are used in many genres, including jazz, blues, funk , sixties pop, and indie rock . They generally have cello-style F-shaped sound holes , which can be blocked off to further reduce feedback. Whereas chambered guitars are made, like solid-body guitars, from
3600-543: A spaced humbucking pair, which significantly reduces 50/60 cycle hum. Fender introduced a five-way selector in 1977, making such pickup combinations more stable. The "quacky" or "doinky" tone of the bridge and middle pickups in parallel, popularized by players such as Jimi Hendrix , Eric Clapton , Stevie Ray Vaughan , David Gilmour , Rory Gallagher , Mark Knopfler , Bob Dylan , Eric Johnson , Nile Rodgers , George Harrison , Scott Thurston , Ronnie Wood , John Mayer , Ed King , Robert Cray , can be obtained by using
3750-553: A sustained chord without disturbing the tuning of the guitar. To fully achieve this benefit however, correct setup, as per Fender's recommendations, was essential. In addition to the Jazzmaster, Fender used the floating tremolo on the then top-of-the-line Fender Jaguars , released in 1962, and also on the Fender Bass VI , released in 1961. Jaguar and Jazzmasters share the same bridge plate and string saddles, though Jaguar bridges (and
3900-502: A tailpiece bar to which the vibrato arm is visibly connected, similar to the Bigsby, and the mechanism is installed from the top of the instrument, similar to the floating tremolo. It combines some features of all three basic designs. The Dynamic Vibrato is often confused with the Fender floating tremolo, which it resembles. The original production runs of the two overlap by more than a decade, but
4050-399: A tip and sleeve configuration referred to as a TS phone connector . The voltage is usually around 1 to 9 millivolts . A few guitars, such as Rickenbacker guitars equipped with Rick-O-Sound , feature stereo output. There are a variety of ways the "stereo" effect may be implemented. Commonly, but not exclusively, stereo guitars route the neck and bridge pickups to separate output buses on
4200-406: A tone control that incorporates a single, shared tone capacitor, whereas the bridge pickup, which is slanted towards the high strings for a more trebly sound, has no tone control for maximum brightness. On many modern Stratocasters, the first tone control affects the neck pickup; the second tone control affects the middle and bridge pickups; on some Artist Series models Buddy Guy signature guitar),
4350-405: A top so heavily reinforced that it essentially functioned as a solid-body instrument. Unlike acoustic guitars, solid-body electric guitars have no vibrating soundboard to amplify string vibration. Instead, solid-body instruments depend on electric pickups, and an amplifier ("amp") and speaker . The solid body ensures that the amplified sound reproduces the string vibration alone, thus avoiding
4500-404: A tremolo effect via a tremolo circuit . Doc Kauffman patent application for his "Vibrola" device (see below) spoke of "producing tremolo effects" in 1928. Other widely used names for the device include "vibrato bar" and "whammy bar", the latter attributed to guitarist Lonnie Mack 's aggressive, rapid manipulation of the pitch-bending device in his 1963 song " Wham! " It has also been called
4650-667: A triple single-coil guitar. The history of electric guitars has been summarized by Guitar World magazine, and the earliest electric guitar on their top 10 list is the Ro-Pat-In Electro A-25 "Frying Pan" (1932) described as "The first-fully functioning solid-body electric guitar to be manufactured and sold". It was the first electric guitar used in a publicly promoted performance, performed by Gage Brewer in Wichita, Kansas in October 1932. The most recent electric guitar on this list
Fender Stratocaster - Misplaced Pages Continue
4800-590: A typical small radius of approximately 7.25 inches (18.4 cm). Some manufacturers have experimented with fret profile and material, fret layout, number of frets, and modifications of the fingerboard surface for various reasons. Some innovations were intended to improve playability by ergonomic means, such as Warmoth Guitars' compound radius fingerboard. Scalloped fingerboards added enhanced microtonality during fast legato runs. Fanned frets intend to provide each string with an optimal playing tension and enhanced musicality. Some guitars have no frets , while others, like
4950-409: A way to reduce or counter the sound, as they are designed to "buck" (in the verb sense of oppose or resist ) the hum, hence their name. The high combined inductance of the two coils also leads to the richer, "fatter" tone associated with humbucking pickups. Electric guitar necks vary in composition and shape. The primary metric of guitar necks is the scale length , which is the vibrating length of
5100-409: A wood post with a neck attached and two hollow-body halves attached to the sides for appearance only — shares nothing in common for design or hardware with the solid-body Gibson Les Paul , designed by Ted McCarty and introduced in 1952. The feedback associated with amplified hollow-bodied electric guitars was understood long before Paul's "log" was created in 1940; Gage Brewer's Ro-Pat-In of 1932 had
5250-457: Is a guitar that requires external electric sound amplification in order to be heard at typical performance volumes, unlike a standard acoustic guitar . It uses one or more pickups to convert the vibration of its strings into electrical signals , which ultimately are reproduced as sound by loudspeakers . The sound is sometimes shaped or electronically altered to achieve different timbres or tonal qualities via amplifier settings or knobs on
5400-517: Is balanced against a single, short helical compression spring , positioned under the arm pivot. Blues-rock guitar pioneer Lonnie Mack , who considered Travis one of his three most significant guitar inspirations, was known for using a Bigsby on his 1958 Gibson Flying V electric guitar. The Bigsby remains popular, especially on hollow-body guitars. It's available as a factory-fitted option on top-line models both hollow and solid-bodied from many makers, and as an aftermarket addition. It remains
5550-436: Is balanced against two medium length helical springs under tension, mounted on the underside of the tremolo mounting plate, one attached to each of the two feet of the tailpiece bar. Dynamic Vibrato units may be recognized by the integrated floating bridge and the stamps "Fender" and "DYNAMIC VIBRATO". Many but not all units also have the words "PAT PEND" or "PAT. NO. 3,241,418" stamped under the word "Fender". The Dynamic Vibrato
5700-445: Is capable of a multitude of sounds and styles in genres ranging from pop and rock to folk to country music , blues and jazz . It served as a major component in the development of electric blues , rock and roll , rock music , heavy metal music and many other genres of music. Electric guitar design and construction varies greatly in the shape of the body and the configuration of the neck, bridge, and pickups. Guitars may have
5850-447: Is considerable debate about the effects on tone and sustain of the material used in the vibrato system's 'inertia bar' and many aftermarket versions are available. The Stratocaster features three single coil pickups , with the output originally selected by a 3-way switch. Guitarists soon discovered that by positioning the switch in between the first and second position, both the bridge and middle pickups could be selected, and similarly,
6000-545: Is made of solid wood, without functionally resonating air spaces. The first solid-body Spanish standard guitar was offered by Vivi-Tone no later than 1934. This model featured a guitar-shaped body of a single sheet of plywood affixed to a wood frame. Another early, substantially solid Spanish electric guitar, called the Electro Spanish, was marketed by the Rickenbacker guitar company in 1935 and made of Bakelite . By 1936,
6150-406: Is often used in two roles: as a rhythm guitar , which plays the chord sequences or progressions , and riffs , and sets the beat (as part of a rhythm section ); and as a lead guitar , which provides instrumental melody lines, melodic instrumental fill passages, and solos . In a small group, such as a power trio , one guitarist may switch between both roles; in larger groups there is often
Fender Stratocaster - Misplaced Pages Continue
6300-418: Is subtle. In acoustic and archtop guitars, wood choices more clearly affect tone. Woods typically used in solid-body electric guitars include alder (brighter, but well rounded), swamp ash (similar to alder, but with more pronounced highs and lows), mahogany (dark, bassy, warm), poplar (similar to alder), and basswood (very neutral). Maple , a very bright tonewood , is also a popular body wood but
6450-425: Is the most widely copied vibrato system. The original design is still in production virtually unchanged today. The synchronized tremolo may have been the reason for the popularity of the Stratocaster among rock musicians in the late '60s and '70s. Owing to its superiority in aggressive use, all Fender guitars using any other vibrato system other than the synchronized tremolo were for a time withdrawn, to return to
6600-470: Is uncertain, as Bigsby kept few records, but it was on Bigsby-built guitars photographed in 1952, in what became its standard form. In several interviews, the late Merle Travis , for whom Bigsby designed his first vibrato, recalled the prototype as being built for him in the "late '40s". The design uses a spring-loaded arm that rotates a cylindrical bar in the tailpiece, varying the string tension to create vibrato and other pitch variations. The string tension
6750-450: Is very heavy. For this reason, it is often placed as a "cap" on a guitar made primarily of another wood. Cheaper guitars are often made of cheaper woods, such as plywood , pine , or agathis —not true hardwoods—which can affect durability and tone. Though most guitars are made of wood, any material may be used. Materials such as plastic, metal, and even cardboard have been used in some instruments. The guitar output jack typically provides
6900-570: The Fender Showman amplifier . In the early 1960s, the instrument was also championed by Hank Marvin , guitarist for the Shadows , a band that originally backed Cliff Richard and then produced instrumentals of its own. In December 1964, George Harrison and John Lennon acquired Stratocasters and used them for " Help! ", and onwards. The double unison guitar solo on " Nowhere Man ", was played by Harrison and Lennon on their new Stratocasters. After
7050-685: The Gibson Les Paul , Gibson SG , and Fender Telecaster , it is one of the most-often emulated electric guitar shapes. The guitar introduced into the popular market several features that were innovative for electric guitars in the mid-1950s. The distinctive body shape, which has become commonplace among electric guitars, was revolutionary for the time period, and for the first time a mass-market electric guitar did not significantly resemble earlier acoustic models. The double cutaway, elongated horns, and heavily contoured back were all designed for better balance and comfort to play while standing up and slung off
7200-721: The Gibson SG used by Angus Young from the group AC/DC . Some otherwise solid-bodied guitars, such as the Gibson Les Paul Supreme, the PRS Singlecut, and the Fender Telecaster Thinline , are built with hollow chambers in the body. These chambers are designed to not interfere with the critical bridge and string anchor point on the solid body. In the case of Gibson and PRS, these are called chambered bodies . The motivation for this may be to reduce weight, to achieve
7350-461: The Gittler guitar , have no neck in the traditional sense. Vibrato systems for guitar A vibrato system on a guitar is a mechanical device used to temporarily change the pitch of the strings. It adds vibrato to the sound by changing the tension of the strings, typically at the bridge or tailpiece of an electric guitar using a controlling lever , which is alternately referred to as
7500-524: The Jaguar . During the CBS era, particularly the 1970s, the perceived quality of Fender instruments fell. During this time, vintage instruments from the pre-CBS era became popular. When the Fender company was bought from CBS by a group of investors and employees headed by Bill Schultz in 1985, manufacturing resumed its former high quality, and Fender was able to regain market share and brand reputation. Dan Smith, with
7650-649: The Slingerland company introduced a wooden solid-body electric model, the Slingerland Songster 401 (and a lap steel counterpart, the Songster 400). Gibson's first production electric guitar, marketed in 1936, was the ES-150 model ("ES" for "Electric Spanish", and "150" reflecting the $ 150 price of the instrument, along with matching amplifier). The ES-150 guitar featured a single-coil, hexagonally shaped "bar" pickup, which
SECTION 50
#17330855256987800-494: The floating tremolo , which was promoted by Fender as their premium unit, but later Mustangs returned to the Dynamic Vibrato. The Dynamic Vibrato is still preferred by some lead guitarists above all other designs. It features a floating bridge similar to that of the floating tremolo, but the bridge is integral with the vibrato unit, unlike that of the floating tremolo, which is mounted separately. The strings are controlled by
7950-409: The six-string guitar (the most common type), which is usually tuned E, A, D, G, B, E, from lowest to highest strings; the seven-string guitar , which typically adds a low B string below the low E; the eight-string guitar , which typically adds a low E or F# string below the low B; and the twelve-string guitar , which has six two-string courses similar to a mandolin . In rock, the electric guitar
8100-418: The wolf tones and unwanted feedback associated with amplified acoustic guitars. These guitars are generally made of hardwood covered with a hard polymer finish, often polyester or lacquer. In large production facilities, the wood is stored for three to six months in a wood-drying kiln before being cut to shape. Premium custom-built guitars are frequently made with much older , hand-selected wood. One of
8250-569: The "Frying Pan", and set out to capture a new audience through its release of the Electro-Spanish Model B and the Electro-Spanish Ken Roberts , which was the first full 25-inch scale electric guitar ever produced. The Electro-Spanish Ken Roberts was revolutionary for its time, providing players a full 25-inch scale, with easy access to 17 frets free of the body. Unlike other lap-steel electrified instruments produced during
8400-481: The "Original Contour Body") differed from the flat, squared edge design of the Telecaster . The Stratocaster's double cutaways allowed players easier access to higher positions on the neck. The first model offered for sale was the 1954 Fender Stratocaster. The design featured a solid, deeply contoured ash body, a 21-fret one-piece maple neck with black dot inlays, and Kluson SafeTi String post tuning machines. The color
8550-413: The 1980s, shred guitarists Eddie Van Halen , Eric Johnson , Joe Satriani and Steve Vai , and metal guitarists Kerry King , Ritchie Blackmore , Kirk Hammett , Terje Rypdal , Vernon Reid , David Torn and David Duhig used vibrato in a range of metal-influenced styles, many aided by the development of the double-locking design pioneered by Floyd Rose or the later Kahler , which eliminated many of
8700-534: The Broadcaster. Another notable solid-body design is the Fender Stratocaster , which was introduced in 1954 and became extremely popular among musicians in the 1960s and 1970s for its wide tonal capabilities and more comfortable ergonomics than other models. Different styles of guitar have different pick-up styles, the main being 2 or 3 " single-coil " pick-ups or a double humbucker , with the Stratocaster being
8850-462: The Fender Stratocasters manufactured were made in a single year, in 1979. The increased 1970s production levels saw a gradual departure from the high quality instruments of the 1960s and the introduction of Japanese manufacturers into the market. Original Stratocasters were manufactured with five vibrato springs (three in late 1953 prototypes) attached to a milled inertia block and anchored to
9000-576: The Fender two-point system has been redesigned with new vintage-style bent sheet steel saddles as of 2008. The Fender two-point system is available with two types of "tremolo bars": traditional "screw-in" type with a plastic tip at the end and deluxe "pop-in" type without the plastic tip. Not to be confused with the similarly named Floyd Rose two-point locking tremolo , the two systems use the words two-point to describe entirely different concepts. The floating bridge featured on two Fender "tremolo arm" designs, both developed by Leo Fender subsequently to
9150-618: The Gibson Vibrato. Its vibrato arm and all subsequent designs adopted the action popularized by Bigsby and Fender. Short version of Deluxe Gibson Vibrola was fitted as standard to the 1967 reissue Gibson Flying V . Also, there are two other names on the Deluxe Gibson Vibrato : " Lyre Vibrola " nicknamed after the lyre engraved on the cover plate, which was fitted to Gibson ES-335 series as an option by 1964; and " Maestro Vibrola " renamed for keeping Maestro brand, which
SECTION 60
#17330855256989300-774: The Highway One and American Special Stratocasters) and the more expensive American Ultra Stratocaster (successor to the American Elite Stratocaster). Fender has also manufactured guitars in East Asia, notably Japan, and in Mexico, where the affordable Player (successor to Standard) series guitars are built. In addition to the Player series, Fender has also released the Player Plus series that features noiseless pickups, locking tuners, and
9450-414: The Stratocaster by other manufacturers are sometimes called S-Type or ST-type guitars. Many prominent rock musicians have been associated with the Stratocaster for use in studio recording and live performances , most notably Eric Clapton , Buddy Holly , David Gilmour , Mark Knopfler , Jimi Hendrix , Stevie Ray Vaughan , John Frusciante , Jeff Beck , George Harrison , and Tom Petty . Along with
9600-442: The Stratocaster tremolo and its derivatives made possible. They have almost always been offered as extra cost options on guitars that sold better in non-vibrato versions. As a result, some versions are rare and command high prices from restorers and collectors. Gibson encourages this trend by refusing to sell reissue units as parts, offering them only on complete guitars (a policy similar to most guitar manufacturers). As of 2006 Gibson
9750-516: The Vibrola as an option on some archtop guitars from 1935 to 1937. Epiphone sold the Vibrola as an aftermarket option as well. This Vibrola was also used on some Rickenbacker lap steel guitars at around the same time and was introduced on their six string 'Electro Spanish' guitars beginning about 1937. Some early Vibrolas on Rickenbacker guitars were not operated by hand, but rather moved with an electrical mechanism developed by Doc Kauffman to simulate
9900-449: The amount of movement over the pickups. Because of their natural qualities, magnetic pickups tend to pick up ambient, usually unwanted electromagnetic interference or EMI. This mains hum results in a tone of 50 or 60 cycles per second depending on the powerline frequency of the local alternating current supply. The resulting hum is particularly strong with single-coil pickups. Double-coil or " humbucker " pickups were invented as
10050-556: The archtop guitars, and their continued strength and focus on this market, but carries over even to the designs used only on solid body guitars, such as the Short Lyre Vibrola used on some Flying V and SG models. While these do require some woodwork for installation (primarily drilling), this is minimal in comparison to the routing required for the more common Fender synchronized, floating, and dynamic vibratos. The Gibson Vibrato , an earliest Gibson-designed vibrato systems,
10200-404: The back of the "tremolo mounting plate". The spring is adjustable by turning a screw located towards the center of this plate. The ferrule ends of the strings are held on the top of the guitar in a tailpiece plate called the knife plate , which emerges from the mechanism, rather than the strings vanishing into the mechanism as with the synchronized tremolo. It is the knife plate that is moved when
10350-418: The back of the body. The novel mechanism pivots on a fulcrum design with a six screw bridge plate, allowing the whole set-up to "float" while transferring the strings' energy directly into the body. Though advertised as "Tremolo" (a change in volume amplitude), vibrato is the correct term for pitch variation. In the floating position, players can move the bridge-mounted vibrato tremolo arm up or down to modulate
10500-407: The back of the guitar body, and is mounted on the guitar body in a routed bay extending behind the pickups, the entire mechanism of the floating tremolo is mounted on a roughly triangular chromed plate in the front of the guitar body, on the opposite side of the bridge to the pickups. The string tension is balanced against a single short helical spring, in compression rather than tension , mounted on
10650-616: The back of the guitar by metal ferrules . Many believe this design improves a guitar's sustain and timbre . A few examples of string-through body guitars are the Fender Telecaster Thinline , the Fender Telecaster Deluxe , the B.C. Rich IT Warlock and Mockingbird, and the Schecter Omen 6 and 7 series. Compared to an acoustic guitar, which has a hollow body, electric guitars make much less audible sound when their strings are plucked, so electric guitars are normally plugged into
10800-418: The body at the base of the guitar. These appear on Rickenbackers , Gretsches , Epiphones , a wide variety of archtop guitars , particularly jazz guitars , and the 1952 Gibson Les Paul. Pictured is a tremolo arm or vibrato tailpiece - style bridge and tailpiece system, often called a whammy bar or trem . It uses a lever ("vibrato arm") attached to the bridge that can temporarily slacken or tighten
10950-430: The body. Set-in necks are glued to the body at the factory. This is the traditional type of joint. Leo Fender pioneered bolt-on necks on electric guitars to facilitate easy adjustment and replacement. Neck-through instruments extend the neck to the length of the instrument so that it forms the center of the body. While a set-in neck can be carefully unglued by a skilled luthier , and a bolt-on neck can simply be unscrewed,
11100-555: The bridge on top of the instrument, resulting in a weak signal. Electric guitars were originally designed by acoustic guitar makers and instrument manufacturers. The demand for amplified guitars began during the big band era; as orchestras increased in size, guitar players soon realized the necessity in guitar amplification and electrification. The first electric guitars used in jazz were hollow archtop acoustic guitar bodies with electromagnetic transducers . The first electrically amplified stringed instrument to be marketed commercially
11250-399: The catalog as classic or retro models in the '90s. Later models are pivoted about two specially shaped studs rather than a row of six screws. This development sacrifices economical manufacture for decreased friction at the pivot point. Currently, the Fender two-point system is their standard and most popular design. Featuring stainless steel block saddles since its introduction in 1986,
11400-546: The closer the fret spacing. Opinions vary regarding the effect of scale length on tone and feel. Popular opinion holds that longer scale length contributes to greater amplitude . Reports of playing feel are greatly complicated by the many factors involved in this perception. String gauge and design, neck construction and relief, guitar setup, playing style, and other factors contribute to the subjective impression of playability or feel. Necks are described as bolt-on , set-in , or neck-through , depending on how they attach to
11550-484: The company by the time it appeared. Basically, a synchronized tremolo simplified to reduce cost, it had little popularity, and as of 2005 was the only Leo Fender vibrato arm design not available on any current Fender model. In 1981 G&L released the F-100 guitar with a dual-fulcrum vibrato designed by Leo Fender, one of G&L's owners. From the 1950s, Gibson offered either a guitar-shaped Gibson Vibra-Rest or
11700-471: The date and country of manufacture. The number and length of springs may be adjusted to set the neutral position of the bridge, determining the range of upward and downward pitch bending available. A bridge set to 'float' off the guitar lets the guitarist raise the pitch until the bridge presses against the body. Pitch bends are accomplished by pulling up or down on an arm screwed into the tailpiece block, usually free to swing. The Fender synchronized tremolo
11850-414: The design over the years and models with features that differ from the archetypical design. However, the essential character of the design has remained constant. The Stratocaster was the first Fender guitar to feature three pickups and a spring tension vibrato system , as well as being the first Fender with a contoured body. The Stratocaster's sleek, contoured body shape (officially referred to by Fender as
12000-453: The device, such as the 1980s-era shred guitar " dive bomb " effect. The mechanical vibrato systems began as a device for more easily producing the vibrato effects that blues and jazz guitarists had achieved on arch top guitars by manipulating the tailpiece with their picking hand. Guitar makers have developed a variety of vibrato systems since the 1890s. A vibrato-equipped guitar is typically more difficult to re-string and tune than
12150-399: The different parts of an electric guitar. The headstock (1) contains the metal machine heads (1.1), which use a worm gear for tuning. The nut (1.4)—a thin fret-like strip of metal, plastic, graphite, or bone—supports the strings at the headstock end of the instrument. The frets (2.3) are thin metal strips that stop the string at the correct pitch when the player pushes a string against
12300-409: The earliest Jazzmaster bridges) have taller legs . The two are functionally interchangeable and replacement parts for each are identical. The Bass VI bridge has a wider plate and longer intonation screws to accommodate bass string intonation, and the saddles have threads cut for larger diameter strings. There have also been a small number of not very notable imitations by other makers, generally without
12450-538: The effects of different woods or materials on the electric guitar sound. Several neck shapes appear on guitars, including shapes known as C necks, U necks, and V necks. These refer to the cross-sectional shape of the neck (especially near the nut). Several sizes of fret wire are available, with traditional players often preferring thin frets, and metal shredders liking thick frets. Thin frets are considered better for playing chords, while thick frets allow lead guitarists to bend notes with less effort. An electric guitar with
12600-467: The electric guitar was adopted by jazz guitar players, who wanted to play single-note guitar solos in large big band ensembles. Early proponents of the electric guitar on record include Les Paul , Eddie Durham , George Barnes , Lonnie Johnson , Sister Rosetta Tharpe , T-Bone Walker , and Charlie Christian . During the 1950s and 1960s, the electric guitar became the most important instrument in popular music . It has evolved into an instrument that
12750-422: The event of a string breaking and strives to provide tuning stability similar to a fixed bridge guitar. In practice, the lock doesn't generally achieve as much stability as a fixed bridge, leading some players to replace the mechanism with a fixed bridge and tailpiece. The "floating tremolo" was greatly favored by some surf music bands, particularly for its ability to produce a pronounced and distinctive vibrato on
12900-607: The finest to ever leave Fender's Fullerton plant, which closed its doors in late 1984. In 1985, Fender's US production of the Vintage reissues resumed into a new 14,000 square feet (1,300 m) factory at Corona, California, located about 20 miles (32 km) away from Fullerton. Some early reissues from 1986 were crafted with leftover parts from the Fullerton factory. Fender released their first Stratocaster signature guitar for Eric Clapton in 1988. A popular Fender Reissue Stratocaster
13050-420: The fingerboard. The truss rod (1.2) is a metal rod (usually adjustable) that counters the tension of the strings to keep the neck straight. Position markers (2.2) provide the player with a reference to the playing position on the fingerboard. The neck and fretboard (2.1) extend from the body. At the neck joint (2.4), the neck is either glued or bolted to the body. The body (3) is typically made of wood with
13200-432: The first improvements on the vibrato system in many years when, in the late 1970s, he experimented with "locking" nuts and bridges that prevent the guitar from losing tuning, even under heavy vibrato bar use. The fourth type of system employs string-through body anchoring. The strings pass over the bridge saddles, then through holes through the top of the guitar body to the back. The strings are typically anchored in place at
13350-432: The first solid-body guitars was invented by Les Paul . Gibson did not present their Gibson Les Paul guitar prototypes to the public, as they did not believe the solid-body style would catch on. Another early solid-body Spanish style guitar, resembling what would become Gibson's Les Paul guitar a decade later, was developed in 1941 by O.W. Appleton, of Nogales, Arizona. Appleton made contact with both Gibson and Fender but
13500-405: The first tone control is a presence circuit that cuts or boosts treble and bass frequencies, affecting all the pickups; the second tone control is an active midrange booster that boosts the midrange frequencies up to 25 dB (12 dB on certain models) to produce a fatter humbucker -like sound. Dick Dale was a prominent Stratocaster player who also collaborated with Leo Fender in developing
13650-442: The floating bridge has an excessive propensity to detune guitars. These guitarists inhibit the bridge's movement with a chunk of wood wedged between the bridge block and the inside cutout of the tremolo cavity, and by increasing the tension on the tremolo springs; these procedures lock the bridge in a fixed position. Some Stratocasters have a fixed bridge in place of the vibrato assembly; these are colloquially called "hard-tails". There
13800-859: The guitar. A stereo cable then routes each pickup to its signal chain or amplifier. For these applications, the most popular connector is a high-impedance 1 ⁄ 4 inch (6.35 mm) plug with a tip, ring, and sleeve configuration, also known as a TRS phone connector . Some studio instruments, notably certain Gibson Les Paul models, incorporate a low- impedance three-pin XLR connector for balanced audio . Many exotic arrangements and connectors exist that support features such as midi and hexaphonic pickups. The bridge and tailpiece , while serving separate purposes, work closely together to affect playing style and tone. There are four basic types of bridge and tailpiece systems on electric guitars. Within these four types are many variants. A hard-tail guitar bridge anchors
13950-404: The guitar. Often, this is done through the use of effects such as reverb , distortion and "overdrive" ; the latter is considered to be a key element of electric blues guitar music and jazz , rock and heavy metal guitar playing. Designs also exist combining attributes of electric and acoustic guitars: the semi-acoustic and acoustic-electric guitars. Invented in 1932 by Johannes Isaac,
14100-405: The guitar. Various other companies have produced their own Strat-style bodies known as Superstrats . The archetypal Stratocaster is a solid-body electric guitar with a contoured asymmetric double-cutaway body with an extended upper horn; the body is usually made from alder or ash. The neck is usually made from maple and attached to the body with screws (often referred to as " bolts ") and has
14250-552: The help of John Page, proceeded to work on a reissue of the most popular guitars of Leo Fender's era. They decided to manufacture two Vintage reissue Stratocaster models, the one-piece maple neck 1957 and a rosewood-fretboard 1962 along with the maple-neck 1952 Telecaster, the maple-neck 1957 and rosewood-fretboard 1962 Precision Basses, as well as the rosewood-fretboard "stacked knob" 1962 Jazz Bass. These first few years (1982–1984) of reissues, known as American Vintage Reissues, are now high-priced collector's items and considered as some of
14400-459: The impact of the Bigsby and Fender designs, and have inspired few if any copies, but they competed reasonably successfully and continue to sell. Gibson designs tend to have the mechanism surface-mounted on the belly of guitar, similar to the Bigsby, and are therefore equally suitable for use on acoustic guitars and especially on archtops . This reflects the Gibson company's history as the developer of
14550-499: The instrument has a tendency to go out of tune during double-stop string bends. Many Stratocaster players opt to tighten the springs (or even increase the number of springs used) so that the bridge is firmly anchored against the guitar body: in this configuration, the vibrato arm can still be used to slacken the strings and therefore lower the pitch, but it cannot be used to raise the pitch (a configuration sometimes referred to as "dive-only"). Some players, such as Ronnie Wood , feel that
14700-578: The introduction of the Fender Stratocaster Ultra series in 1989, ebony was officially selected as a fretboard material on some models (although several Elite Series Stratocasters manufactured in 1983/84 such as the Gold and Walnut were available with a stained ebony fretboard). In December 1965 the Stratocaster was given a broader headstock with altered decals to match the size of the Jazzmaster and
14850-403: The late 1960s. His remarkable playing style and musical prowess led to a dramatic increase in sales and thrust the Stratocaster into musical history as the premier electric guitar. As they followed Jimi Hendrix's popularity on TV, CBS asked for the word Stratocaster on the headstock be made larger so that people could read the model name easily. Between the years 1954 and 1979, nearly a quarter of
15000-449: The late 1970s, Fender stopped shipping guitars with the bridge cover plate, though some more modern reissue and custom shop models still have them. The innovative tremolo system is balanced by springs mounted in a rear cavity. The output jack is mounted in a recess in the front of the guitar body. Many different colors have been available. The Stratocaster's scale length is 25.5 inches (648 mm). There have been some minor changes to
15150-649: The list. The neck and fingerboard can be made from different materials; for example, a guitar may have a maple neck with a rosewood or ebony fingerboard. Today there are expensive and budget guitars exploring other options for fretboard wood for instance Pau-Ferro , both for availability and cheap price while still maintaining quality. In the 1970s, designers began to use exotic human-made materials such as aircraft-grade aluminum , carbon fiber , and ebonol . Makers known for these unusual materials include John Veleno , Travis Bean , Geoff Gould , and Alembic . Aside from possible engineering advantages, some feel that with
15300-405: The locking knob. Fender discontinued all floating tremolo models by 1980, but reintroduced both the Jazzmaster and Jaguar first as Japanese models in the mid 1980s, then as American-made reissues in the 1990s. The tremolo-equipped Bass VI was reintroduced as a US Custom Shop model in 2006. An advantage or disadvantage, depending on taste, is string resonance audible at several fret positions where
15450-416: The low break-angle over the bridge and, in the Jaguar's case, the exceptionally short scale length of 24 inches. This places relatively little downwards force on the bridge, making it unreliable in returning to the correct position after tremolo operation. The main difference is that, while much of the mechanism of the synchronized tremolo including the springs is accessed by removing a rectangular plate in
15600-414: The mechanisms are quite different. The existence of a few 1960s Mustangs factory fitted with the floating tremolo has probably added to the confusion. The concealed mechanism is in a chamber of a completely different shape and position, requiring an impractical amount of woodwork to convert from one to the other, and the mounting plate is of a different shape with different mounting holes. The string tension
15750-409: The middle and neck pickups could be selected between the 2nd and 3rd position. When two pickups are selected simultaneously, they are wired in parallel which leads to a slight drop in output as slightly more current is allowed to pass to the ground. In newer guitars, since the middle pickup is almost always wired in reverse (and with its magnets having opposite polarity), the intermediate positions create
15900-459: The more common pivoting "tremolo" bridges , and the less common "hardtail" fixed bridge. Both types of bridge have six individually adjustable saddles whose height and intonation can be set independently. Early models of the stratocaster came with a removable metal cover plate that fit over the bridge. The plate was purely cosmetic, and tended to get in the way of important playing techniques such as palm muting , so many players removed it. By
16050-528: The most popular electric guitar in history, Leo Fender made very few alterations to the basic design of the Fender Stratocaster (and the Telecaster for that matter) up until 1965 when the company was sold to CBS Instruments. For example, the bridge cover on the Fender Stratocaster was often taken off by players and either disposed or kept in the case. Despite full knowledge of this, Leo Fender always provided
16200-400: The neck shape took a more "V-shaped" feel with deeper body carves on the guitar a noted feature. In 1959, Fender introduced a thick Brazilian rosewood fretboard to the Stratocaster, now colloquially referred to as a "slab-board". This thicker board lasted until 1962, when the fretboard was made with a thinner 'veneer' of Brazilian Rosewood. Nearly all of the 1960s models of the Stratocaster had
16350-401: The new Fender guitars with a bridge cover to prevent corrosion on the bridge parts. After 1965, the Fender company, under the control of CBS Instruments, saw a drop in sales of the Fender Stratocaster to customers. The Fender Jazzmaster had been promoted as the flagship guitar in the Fender line. As such, the resurgence of the Fender Stratocaster is credited to the arrival of Jimi Hendrix in
16500-418: The only widely used design whose mechanism is entirely above the belly of the guitar body, making it particularly suitable for acoustic and semi-acoustic guitars. After the Bigsby, the next major development was Leo Fender 's synchronized tremolo , the device that introduced the term tremolo arm ( U.S. patent 2,741,146 filed in 1954, issued in 1956). First released in 1954 on Fender 's Stratocaster ,
16650-568: The original synchronized tremolo but overshadowed by it. Despite its not being the most popular bridge, there are benefits unique to guitars with this type of bridge (See 3rd bridge guitars ). The floating tremolo was designed by Fender for the Fender Jazzmaster , and first appeared with the release of the Jazzmaster in 1958. A larger, heavier and more complex vibrato mechanism than the synchronized tremolo and promoted over it by Fender as their premium "tremolo arm" mechanism, it never achieved
16800-482: The other way round when referring to hardware devices and the effects they produce. This reversal of terminology is generally attributed to Leo Fender and the naming of his 1954 Stratocaster mechanical vibrato system as a "Tremolo Device for Stringed Instruments". Additionally, the 1956 Fender "Vibrolux" guitar amplifier , used electronically generated tremolo that Fender called "vibrato". Other classic guitar amplifiers contain electronic " vibrato units " that produce
16950-432: The pickup selector in position 2; similarly the middle and neck pickups in parallel can be obtained in position 4. This setting's characteristic tone is not caused by any electronic phenomenon—early Stratocasters used identical pickups for all positions. This "in between" tone is caused by phase cancellation due to the physical position of the pickups along the vibrating string. The neck and middle pickups are each wired to
17100-423: The pickups do not produce a signal directly from the vibration of the strings, but rather from the vibration of the guitar top or body, and the amplification of the sound merely increases volume, not alters tone. Electric guitar design and construction vary greatly in the shape of the body and the configuration of the neck, bridge, and pickups. However, some features are present on most guitars. The photo below shows
17250-419: The pitch manipulation available with steel guitars. The Vibrola distributed as an option with Rickenbacker Electro Spanish guitars was hand operated like the earliest Epiphone Vibrolas. A later unit was created and used on Rickenbacker's Capri line of guitars in the 1950s, such as John Lennon 's 1958 Rickenbacker 325 . It was a side-to-side action vibrato unit (rather than the up-down action of later units) that
17400-426: The pitch of the notes being played. Hank Marvin , Jeff Beck and Ike Turner have used the Stratocaster's floating vibrato extensively in their playing. As string gauges have changed, players have experimented with the number of springs (often four though Hendrix used five). As the average gauge has decreased over the years, modern Stratocasters are equipped with three springs as a stock option in order to counteract
17550-449: The plate at the center of the design. Six bridge saddles are held against this plate by string tension, individually adjustable both for height and intonation. Another of the components which make up the tailpiece consists of a solid block of metal, commonly made of zinc, but aftermarket products can be made out of materials such as titanium or brass (often like the saddles). The different compositions, as well as its mass, helps to determine
17700-414: The player. Fender has released numerous models with different pickup configurations and has made other small modifications to the electronics and components of the base model, such as changing the initial 3-position selector switch to a standard 5-position selector switch, offering more tonal variety, as well as other small cosmetic changes to things like tuning pegs and types of woods used in various parts of
17850-428: The quality of the sound of the guitar. The block is secured to the base plate by three machine screws and resides in a cavity routed all the way through the guitar's body. In this cavity, up to five coil springs tether the end of the bridge block to the body, counteracting the pull of the strings, should this be the setup choice for the guitarist. There can even be differing sizes of tremolo arms in thickness depending on
18000-414: The recessed jack plate, facilitating assembly. The 1963 Fender Stratocaster shows an advancement in design from the 1950s models including a 'veneer' Brazilian rosewood board with Clay Dot inlays, a 3 tone sunburst finish on an Alder body and Kluson tuners. To summarize, the specific features in the evolution of the Fender Stratocaster between 1954 and 1979 included: Despite being credited with inventing
18150-416: The reduced string tension. While the floating bridge has unique advantages for wavering pitch upwards (like Jeff Beck), the functionality of the "floating" has been widely accepted, yet disputed by some musicians. Leo Fender insisted it leave the factory floating (raised up in the back) while designer Freddie Tavares preferred it tightened flush for full bridge plate/body contact resonance. As the bridge floats,
18300-592: The rising cost of rare tonewoods , human-made materials may be economically preferable and more ecologically sensitive. However, wood remains popular in production instruments, though sometimes in conjunction with new materials. Vigier guitars , for example, use a wooden neck reinforced by embedding a light, carbon fiber rod in place of the usual heavier steel bar or adjustable steel truss rod. After-market necks made entirely from carbon fiber fit existing bolt-on instruments. Few, if any, extensive formal investigations have been widely published that confirm or refute claims over
18450-399: The same popularity, though if properly set up according to Fender's recommendations, it held tune as well as or better than the synchronized tremolo unit. A major cause of the floating tremolo's increasingly poor reputation since its introduction is the far-increased availability and popularity of lighter guitar strings , which do not produce enough tension in standard tuning to compensate for
18600-453: The shoulder with a strap. The three- pickup design offered players increased versatility and choice in tone quality over earlier one- and two-pickup electric guitars, and a responsive and simplified vibrato arm integrated into the bridge plate, which marked a significant design improvement over other vibrato systems, such as those manufactured by Bigsby . All of these design elements were popularized and later became an industry standard due to
18750-426: The simple but effective design offers a greater range of pitch change than the Bigsby, and a better capability for up-bends. Fender wrongly labeled the arm as a "tremolo arm" rather than a "vibrato arm", conversely referring to the tremolo circuit on his amplifiers as "vibrato". Vibrato systems send a guitar out of tune when friction inhibits the vibrating length of string from returning to its original tension after
18900-455: The string tension to the guitar belly, so short versions are generally used only on solid body guitars. Long tailpieces can be used on almost any guitar (an exception being the Gibson Flying V where there is no room for one), and both long and short versions have been used on various models of Gibson SG and Gibson Les Paul guitars. The Gibson designs were less suitable for the sounds that
19050-522: The strings at or directly behind the bridge and is fastened securely to the top of the instrument. These are common on carved-top guitars, such as the Gibson Les Paul and the Paul Reed Smith models , and on slab-body guitars, such as the Music Man Albert Lee and Fender guitars that are not equipped with a vibrato arm. A floating or trapeze tailpiece (similar to a violin 's) fastens to
19200-662: The strings behind the bridge with felt or other material solves the issue. The Fender Dynamic Vibrato (also colloquially referred to as the Mustang tremolo or Stang trem ) was introduced in 1964 on the Fender Mustang , intended as a student model. It was also notably used on the Jag-Stang , a custom design by Nirvana frontman Kurt Cobain combining features of the Jaguar and the Mustang. Some late 1960s Mustangs were fitted instead with
19350-456: The strings from nut to bridge. A typical Fender guitar uses a 25.5-inch (65 cm) scale length, while Gibson uses a 24.75-inch (62.9 cm) scale length in their Les Paul . While the scale length of the Les Paul is often described as 24.75 inches, it has varied through the years by as much as a half inch. Frets are positioned proportionally to scale length—the shorter the scale length,
19500-609: The strings to alter the pitch . A player can use this to create a vibrato or a portamento effect. Early vibrato systems were often unreliable and made the guitar go out of tune easily. They also had a limited pitch range. Later Fender designs were better, but Fender held the patent on these, so other companies used older designs for many years. With the expiration of the Fender patent on the Stratocaster -style vibrato, various improvements on this type of internal, multi-spring vibrato system are now available. Floyd Rose introduced one of
19650-399: The success of the Stratocaster. The Fender Stratocaster is one of the most iconic electric guitar models of all time. Over the years, countless variations of the Stratocaster have been made. The modular nature of the guitar, with its easily removable components, left players and luthiers to perform numerous modifications to their own guitars, changing out pickups or necks to fit the needs of
19800-581: The time, the Electro-Spanish Ken Roberts was designed to play while standing upright with the guitar on a strap, as with acoustic guitars. The Electro-Spanish Ken Roberts was also the first instrument to feature a hand-operated vibrato as a standard arrangement, a device called the "Vibrola", invented by Doc Kauffman . It is estimated that fewer than 50 Electro-Spanish Ken Roberts were constructed between 1933 and 1937; fewer than 10 are known to survive today. The solid-body electric guitar
19950-402: The tremolo arm is operated. Unlike the synchronized tremolo, the bridge is not moved directly by the mechanism, but only by the movement of the strings, and is allowed to tilt to accommodate this movement. This is called a floating bridge . The Fender floating tremolo also features a knob that enables the player to lock, and thus disable, the tremolo mechanism. This facilitates quick retuning in
20100-415: The tuning issues associated with more basic designs and allowed guitarists to employ dramatic "dive bomb" effects freely throughout a performance. Though a guitar's "tremolo arm" can produce variations of pitch , including vibrato, it cannot produce tremolo (rapid modulation of volume). However it has become common practice for electric guitarists and manufacturers to use the terms vibrato and tremolo
20250-660: The vibrations of the guitar strings into electrical signals, which could then be amplified. Commercial production began in late summer of 1932 by the Ro-Pat-In Corporation (Elect ro - Pat ent- In strument Company), in Los Angeles, a partnership of Beauchamp, Adolph Rickenbacker (originally Rickenbacher), and Paul Barth. In 1934, the company was renamed the Rickenbacker Electro Stringed Instrument Company. In that year Beauchamp applied for
20400-489: Was a cast aluminium lap steel guitar nicknamed the "Frying Pan" designed in 1931 by George Beauchamp , the general manager of the National Stringed Instrument Corporation , with Paul Barth, who was vice president. George Beauchamp, along with Adolph Rickenbacker , invented the electromagnetic pickups. Coils that were wrapped around a magnet would create an electromagnetic field that converted
20550-439: Was a distinctive long tailpiece released in 1962 on some SG models. This mechanism later became known as the side-to-side vibrato (or Sideways Vibrola ) because of the position of the lever, which emerged from the side of the long tailpiece. This lever had only restricted movement up and down in a plane close to that of the strings, so its action was unlike that of the Bigsby and Fender units, and remains unique. It
20700-525: Was also described as the " Gibson Vibrola Tailpiece " in Gibson documents, but this name can be applied to any of the Gibson vibrato mechanisms. It was not a success and is of interest mainly to historians and collectors. Also an earliest short vibrato, referred as " ebony vibrato with the inlaid pearl ", was seen on the several Les Paul/SG Standard in the same year. The Deluxe Gibson Vibrato (or Gibson Deluxe Vibrola , etc )—another long tailpiece mechanism, released in 1963—replaced
20850-469: Was an option on the ES-335 by 1967. Most Vibrola tailpieces, including the Bigsby , Lyre and Maestro , exist in both long and short versions. The long version replaces a trapeze-style tailpiece, such as found on most archtop guitars , and transmits the string tension to the guitar side. The short version replaces a string stop style tailpiece, such as found on the original Gibson Les Paul , and transmits
21000-475: Was designed by Walt Fuller. It became known as the " Charlie Christian " pickup (named for the jazz guitarist who was among the first to perform with the ES-150 guitar). The ES-150 achieved some popularity but suffered from unequal loudness across the six strings. A functioning solid-body electric guitar was designed and built in 1940 by Les Paul from an Epiphone acoustic archtop as an experiment. His " log guitar " —
21150-631: Was discontinued in 2008. The Custom Classic Strat was intended to be a combination of the best aspects of vintage and modern Strats. The guitar boasted 3 Modern Classic pickups along with a Custom Classic 2-point tremolo with pop-in tremolo bar. The "C" Shaped neck was maple with either maple or rosewood finger board and 22 jumbo frets. The colors available were three-color sunburst, daphne blue, black, bing cherry transparent, cobalt blue transparent, and honey blonde. Fender has released several models of Stratocaster in collaboration with famous guitarists. They include: Electric guitar An electric guitar
21300-497: Was discontinued in 2012. As well as the vintage reissues, Fender launched an updated model in 1987: the American Standard Stratocaster. This was tailored to the demands of modern players, notably having a flatter fingerboard, a thinner neck profile and an improved tremolo system. This model line has been continuously improved and remained in production until late 2016. The model line received upgrades in 2000, when it
21450-437: Was notorious for throwing the guitar out of tune, hence Lennon's replacing his with a Bigsby B5 unit (Lennon's 1964 Rickenbacker 325 came fitted with a Rickenbacker Ac'cent vibrato unit). The first commercially successful vibrato system for guitar was the Bigsby vibrato tailpiece , often just called a Bigsby , invented by Paul Bigsby (US Patent D169120 filed in 1952, issued in 1953). The exact date of its first availability
21600-550: Was officially published in 1932 under the title, Apparatus for producing tremolo effects . Between 1920 and 1980 Kauffman collaborated with many pioneering guitar manufacturers including Rickenbacker, Gibson and Fender. In the late 1930s Rickenbacker produced the first commercial batch of electric Spanish guitars , utilizing the Kauffman "Vib-rol-a" as a stock option, thus setting precedence for electric guitars produced by Fender and Gibson. The Epiphone guitar company first offered
21750-417: Was originally a two-color, dark brown-to-golden yellow sunburst pattern, although custom color guitars were produced (An example is Eldon Shamblin 's gold Stratocaster, dated June 1954). In 1956, Fender began using alder for sunburst and most custom-color Stratocaster bodies. Ash needed grain filler and sanding blocks for contour sanding, though it was still used on translucent blonde instruments. In 1957,
21900-651: Was renamed as the American Series Stratocaster, and again in 2008, when the American Standard name was restored. In 2017, the American Standard Stratocaster was replaced by the American Professional Stratocaster, with narrow frets, a fatter 'deep C' neck profile and V-Mod pickups. Various other modern American-made Stratocasters have been produced. As of 2019, these include the more affordable American Performer Stratocaster (successor to
22050-737: Was the Ibanez Jem (1987) which featured "24 frets", an impossibly thin neck" and was "designed to be the ultimate shredder machine". Numerous other important electric guitars are on the list, including Gibson ES-150 (1936), Fender Telecaster (1951), Gibson Les Paul (1952), Gretsch 6128 Duo Jet (1953), Fender Stratocaster (1954), Rickenbacker 360/12 (1964), Van Halen Frankenstrat (1975), Paul Reed Smith Custom (1985) many of these guitars were "successors" to earlier designs. Electric guitar designs eventually became culturally important and visually iconic, with various model companies selling miniature model versions of particularly famous electric guitars, for example,
22200-527: Was the '57 American Vintage Reissue. The company regarded 1957 as a benchmark year for the Strat. The original specifications were used, with three 57/62 pickups, aged pickup covers and knobs, a tinted 7.25" radius, 21 fret maple neck, an ashtray bridge cover, and three position switch (with five-position switch kit included). The colors included white blonde, two-color sunburst, black, ocean turquoise, surf green, and ice blue metallic. The '57 Vintage Reissue Stratocaster
22350-447: Was the last of the floating bridge designs Fender discontinued, with the Mustang in 1982—and the first they reintroduced, again with the Mustang, in 1990. Still another design appeared on the student model Fender Bronco , released mid-1967. This was simply known as the Fender vibrato tailpiece , or sometimes the Fender steel vibrato . It was again designed by Leo Fender although he had sold
22500-545: Was unable to sell the idea behind his "App" guitar to either company. In 1946, Merle Travis commissioned steel guitar builder Paul Bigsby to build him a solid-body Spanish-style electric. Bigsby delivered the guitar in 1948. The first mass-produced solid-body guitar was Fender Esquire and Fender Broadcaster (later to become the Fender Telecaster ), first made in 1950, five years after Les Paul made his prototype . The Gibson Les Paul appeared soon after to compete with
#697302