Misplaced Pages

#7992

84-571: The SW1911 ( S mith & W esson) is a stainless steel framed, single action , semi-automatic pistol based on the M1911 , coming in either 9×19mm or .45 ACP . In 2003, Smith & Wesson introduced their variation of the classic M1911 .45 ACP semi-automatic handgun, the SW1911. This firearm retains the M1911's well-known dimensions, operation, and feel, while adding a variety of modern touches. Updates to

168-467: A cam (similar to the action of a screw thread ) which retracts the striker, compressing the cocking spring and holding it there. When the cocking handle is rotated closed, the cocking cam disengages but the striker is retained in the cocked position by the trigger sear. Introduced in the Mauser Model 1871 , it significantly reduced the risk of accidental discharge upon closing. The system of operation

252-411: A quicker initiation of fire, but compromised by having a longer, heavier trigger pull, which can affect accuracy compared to the lighter, shorter trigger pull of a single-action fire. In a DA/SA semi-automatic pistol , the trigger mechanism functions identically to that of a DA revolver. However, this is combined with the ability of the pistol slide to automatically cock the hammer when firing. Thus,

336-436: A "buffer zone" that prevents the shooter from "jerking the trigger", allowing the remnant pressing force from the finger to be dampened via a "follow-through" motion. Although a perceivable overtravel can be felt as adding to the "creep" of the trigger break, it is not always considered a bad thing by some shooters. An overtravel stop will arrest the motion of the trigger blade and prevent excessive movement. When user releases

420-400: A breech-loading shotgun for his cartridge, using a firing pin and external hammer. The Dreyse needle gun of 1836 uses a paper cartridge with a priming as part of a sabot which cradles the projectile and is forward of the propelling charge. The needle-like firing pin projects from the bolt-face and pierces the cartridge when the breech is closed. On firing, the spring-loaded needle strikes

504-477: A cartridge or loading the chamber, the hammer or striker will rest in a partially cocked position. The trigger serves the function of completing the cocking cycle and then releasing the striker or hammer. While technically two actions, it differs from a double-action trigger in that the trigger is not capable of fully cocking the striker or hammer. It differs from single-action in that if the striker or hammer were to release, it would generally not be capable of igniting

588-477: A chambered round) as it is possible for the firing pin to strike the face of the camber and deform it or damage the firing pin. In 1808 by the Swiss gunsmith Jean Samuel Pauly in association with French gunsmith François Prélat created the first cartridges to integrate a primer and be self-contained. The paper cartridge used a metal base with a through-hole coated in a percussive priming compound. Pauly also developed

672-435: A degree of safety in the field compared to having a conventional, very light trigger. There are two types: single set and double set. Set triggers are most likely to be seen on customized weapons and competition rifles where a light trigger pull is beneficial to accuracy. A single set trigger is usually one trigger that may be fired with a conventional amount of trigger pull weight or may be "set" – usually by pushing forward on

756-416: A device which has a similar function. Such equipment or devices include: artillery , munitions and pyrotechnics . The typical firing pin is a thin, simple rod with a hardened, rounded tip that strikes and crushes the primer . The rounded end ensures the primer is indented rather than pierced (to contain propellant gasses). It sits within a hole through the breechblock and is struck by the hammer when

840-509: A firearm that is true to the M1911 design, with additions that would normally be considered "custom", with a price similar to equivalent designs from other manufacturers. Smith & Wesson's Performance Center produces the top-of-the-line hand-fitted competition version knowns as the PC 1911. While most 1911s run around 38 to 39 ounces (1,100 to 1,100 g), the PC 1911 is heavier, at approximately 41 ounces (1,200 g). Single action A trigger

924-401: A fixed firing pin mounted in the breech plug. When a mortar round is dropped down the barrel, a primer in the base of the mortar round strikes the firing pin and ignites the propelling charge. In firearms terminology, a floating firing pin is one which is unrestricted by a firing-pin return spring or similar. While it will be captive and unable to simply fall out, either forward or backward, it

SECTION 10

#1732869803008

1008-424: A heavier weight and little or no discernible movement. A perceivably slow trigger break is often referred to as a "creep", and frequently described as an unfavorable feature. The trigger overtravel happens immediately after the break and is typically a short distance and can be considered an inertially accelerated motion caused by the residual push of the finger coupled with the sudden decrease in resistance after

1092-467: A manual safety that additionally may serve to decock the hammer. Some have a facility (generally a lever or button) to safely lower the hammer. As a disadvantage, these controls are often intermingled with other controls such as slide releases, magazine releases, take-down levers, takedown lever lock buttons, loaded chamber indicators, barrel tip-up levers, etc. These variables become confusing and require more complicated manuals-of-arms. One other disadvantage

1176-527: A police pistol. These weapons also generally lack any type of external safety. DAO is common among police agencies and for small, personal protection firearms. The primary drawback is that the additional trigger pull weight and travel required for each shot reduces accuracy. Pre-set triggers offer a balance of pull weight, trigger travel, safety, and consistency. Glock popularized this trigger in modern pistols and many other manufacturers have released pre-set striker products of their own. The primary disadvantage

1260-456: A primer in the base of the disposable launch tube. The cap contains a fixed firing-pin inside. The flare is fired by placing the cap over the base and striking it by hand. Hand grenades of the type that use a safety lever (such as the M26 grenade ) use a striker that is similar to the classic spring-loaded mousetrap . It is held under tension until the lever is released and then flips over to strike

1344-488: A result an external safety is sometimes employed. Double-action triggers provide the ability to fire the gun whether the hammer is cocked or uncocked. This feature is desirable for military, police, or self-defense pistols. The primary disadvantage of any double-action trigger is the extra length the trigger must be pulled and the extra weight required to overcome the spring tension of the hammer or striker. DA/SA pistols are versatile mechanisms. These firearms generally have

1428-496: A single-action mechanism altogether, more commonly DAO revolvers are modifications of existing DA/SA models, with identical internals, only with access to the hammer prevented, either by covering it with a shroud or by removing the thumb spur. In both cases, the goal is to prevent the possible snagging of the hammer spur on clothing or holster. Due to the imposed limitation in accuracy, the majority of DAO revolvers have been short-barrel, close-range "snub" weapons, where rapidity of draw

1512-401: A spring) the hammer/striker, rotating a revolver 's cylinder , deactivating internal safeties , transitioning between different firing modes (see progressive trigger ), or reducing the pull weight (see set trigger ). A single-action (SA) trigger is the earliest and mechanically simplest of trigger types. It is called "single-action" because it performs the single function of releasing

1596-428: A square or rectangular cross-section and a blunt chisel point. Flat firing pins can be stamped from flat metal stock and usually operate in a slot cut in the breechblock (rather than a hole) that is parallel but offset from the centerline of the barrel. These production methods are generally simpler and reduce production costs. It is generally recommended not to excessively "dry fire" rimfire firearms (ie firing without

1680-415: A trigger pull to both cock and trip the hammer/striker for every single shot, unlike a DA/SA, which only requires a double-action trigger pull for the first shot (or a typical DA/SA revolver, which can fire single action any time the user wishes but uses double-action as a default). This means that there is no single-action function for any shot, and the hammer or striker always rests in the down position until

1764-403: A typical firing pin. Many small- caliber rimfire bolt-action rifles and some centerfire automatic weapons (e. g., vz. 58 ) may appear to have a striker-operated firing mechanism but are actually a type of linear hammer . The hammer can be likened to that of a pile driver and is mainly contained within the bolt. It is much like the striker already described except that the "hammer" upon which

SECTION 20

#1732869803008

1848-426: A way to catch the hammer on release; while the other two have three-position safety selectors and a way to capture the hammer on release. In these triggers, the third position activates the pull and release mode, while the center selector position causes the trigger to only drop the hammer when pulled. A set trigger allows a shooter to have a greatly reduced trigger pull (the resistance of the trigger) while maintaining

1932-430: Is a mechanism that actuates the function of a ranged weapon such as a firearm , airgun , crossbow , or speargun . The word may also be used to describe a switch that initiates the operation of other non-shooting devices such as a trap , a power tool , or a quick release . A small amount of energy applied to the trigger leads to the release of much more energy. Most triggers use a small flattened lever (called

2016-445: Is a trigger that must perform the double function of both cocking and releasing the hammer/striker. Such trigger design either has no internal sear mechanism capable of holding the hammer/striker in a still position (so cocking and releasing have to happen in one uninterrupted sequence), or has the whole hammer shrouded and/or with the thumb spur machined off, preventing the user from manipulating it separately. This design requires

2100-504: Is also known as traditional double-action (TDA), as the vast majority of modern "double-action" handguns (both revolvers and semi-automatic pistols ) use this type of trigger instead of "double-action only" (DAO). In simple terms, "double-action" refers to a trigger mechanism that both cocks the hammer and then releases the sear, thus performing two "acts", although it is supposed to describe doing both strictly with one trigger pull only. However, in practice most double-action guns feature

2184-412: Is essential and limited accuracy is already an acceptable compromise. The purpose of a DAO action in a semi-automatic is mostly to avoid the change in trigger pull between the first and subsequent shots that one experiences in a DA/SA pistol, while avoiding the perceived danger of carrying a cocked single-action handgun, although it also avoids having to carry a cocked and loaded pistol, or having to lower

2268-418: Is essentially a firing pin directly loaded to a spring, eliminating the need to be struck by a separate hammer. The firing pin/striker then collides into the cartridge primer positioned ahead of it, which contains shock-sensitive compounds (e.g., lead styphnate ) that sparks to ignite the propellant powder within the cartridge case and thus discharges the projectile . The trapping interface between

2352-404: Is often considered the most critical stage of the trigger pull for achieving good practical accuracy, since it happens just prior to the shot being discharged and can cause some unwanted shakes from the shooter's hand at the instant of firing. Shooter preferences vary; some prefer a soft break with a smooth but discernible amount of trigger travel during firing, while others prefer a crisp break with

2436-421: Is otherwise free to slide within these stops. The trapdoor Springfield Model 1865 is an example of a floating firing pin. Hammer-operated firing mechanisms use a relatively light firing pin and rely on a transfer of momentum received from a spring -loaded hammer , in the same fashion as a punch or chisel relays the blow from a mallet . In firearms terminology, a striker (or striker mechanism) derives

2520-466: Is that pulling the trigger a second time after a failure to fire will not re-strike the primer. In normal handling of the firearm, this is not an issue; loading the gun requires that the slide be retracted, pre-setting the striker. Clearing a malfunction also usually involves retracting the slide following the " tap rack bang " procedure. Firing pin The terms may also be used for a component of equipment or

2604-399: Is the difference between the first double-action pull and subsequent single-action pulls. DAO firearms resolve some DA/SA shortcomings by making every shot a double-action shot. Because there is no difference in pull weights, training and practice are simplified. Additionally, the heavier trigger pull can help to prevent a negligent discharge under stress. This is a particular advantage for

Smith & Wesson SW1911 - Misplaced Pages Continue

2688-399: Is to rack the slide, clearing the round and recocking the hammer. While this can be advantageous in that many rounds will fire on being struck a second time, and it is faster to pull the trigger a second time than to cycle the action, if the round fails to fire on the second strike, the user will be forced to clear the round anyway, thus using up even more time than if they had simply done so in

2772-622: The LeMat , as well as early metallic cartridge revolvers such as the Colt Model 1873 "Single Action Army" (named for its trigger mechanism) and Smith & Wesson Model 3 , all of which required a thumb to cock the hammer before firing. Single-action triggers with manually cocked external hammers lasted a while longer in some break-action shotguns and in dangerous game rifles, where the hunter did not want to rely on an unnecessarily complex or fragile weapon. While single-action revolvers never lost favor in

2856-544: The Smith & Wesson Centennial , the Type 26 Revolver , and the Enfield No. 2 Mk I* and Mk I** revolvers, in which there is no external hammer spur, or which simply lack the internal sear mechanism capable of holding the hammer in the cocked position. A double-action/single-action (DA/SA) trigger is a hybrid design combining the features of both single- and double-action mechanisms. It

2940-589: The Smith & Wesson Model 27 , S&W Model 60 , the Colt Police Positive , Colt Python , etc. Early double-action revolvers included the Beaumont–Adams and Tranter black-powder muzzleloaders . There are some revolvers that can only be fired in double-action mode (DAO), but that is almost always due to existing double-action/single-action models being modified so that the hammer cannot be cocked manually, rather than from weapons designed that way from

3024-473: The kinetic energy from the spring releasing, and a firing pin to eventually strike and ignite the primer. There are two primary types of striking mechanisms – hammer and striker . A hammer is a pivoting metallic component subjected to spring tension so when released will swing forward to strike a firing pin like a mallet hitting a punch / chisel , which then relays the hammer impulse by moving forward rapidly along its longitudinal axis. A striker

3108-423: The trigger is "pulled". A light firing-pin spring is often used to keep the firing pin rearward. It may be termed a firing-pin return spring , since it returns it to the unfired position. In semi-automatic firearms , this prevents premature firing from the inertia of the firing pin as the breech mechanism closes in the reloading part of the firing cycle. Firing pins of this type are often too short to contact

3192-608: The trigger blade ) depressed by the index finger , but some weapons such as the M2 Browning machine gun or the Iron Horse TOR ("thumb-operated receiver") use a push-button -like thumb-actuated trigger design, and others like the Springfield Armory M6 Scout use a squeeze-bar trigger similar to the "ticklers" on medieval European crossbows . Although the word "trigger" technically implies the entire mechanism (known as

3276-406: The trigger group ), colloquially it is usually used to refer specifically to the trigger blade. Most firearm triggers are "single-action", meaning that the trigger is designed only for the single function of disengaging the sear , which allows for a spring -tensioned hammer / striker to be released. In "double-action" firearm designs, the trigger also performs the additional function of cocking

3360-560: The US right up until the birth of the semi-automatic pistol , double-action revolvers such as the Beaumont–Adams were designed in Europe before the American Civil War broke out and saw great popularity all through the latter half of the 19th century, with certain numbers being sold in the US as well. While many European and some American revolvers were designed as double-action models throughout

3444-406: The barrel. A striker mechanism will consist of the striker spring (firing spring) and the striker. The striker spring is a relatively strong spring sufficient to initiate firing. A typical striker consists of a narrow striking point, a heavier section that acts as a spring guide for the striker spring, a shoulder to restrain the spring, and a catch piece which is engaged by the trigger sear to hold

Smith & Wesson SW1911 - Misplaced Pages Continue

3528-437: The base of the cartridge. The pin needs to be aligned with a corresponding slot in the chamber; a disadvantage compared with rimfire and centerfire cartridges that followed and that are also safer. Early rifle designs that fired metallic cartridges typically used a side-lock mechanism, with the hammer mounted to one side rather than inline with the axis of the barrel. In the trapdoor Springfield Model 1865 (and similar)

3612-502: The bolt is pushed forward to close the breech, the striker catch is held by the trigger sear. The firer must close the bolt with sufficient force to overcome the force exerted by the cocking spring. Notably, the Lee–Enfield and Belgian Mauser cock on closing as do many small-caliber rimfire bolt-action rifles. The breech of a bolt action rifle is opened by first rotating the bolt handle . In cock-on-open operation, this rotation acts on

3696-432: The center of the base of the cartridge. Firing pins for centerfire cartridges usually have a round cross-section and their movement is usually through a hole in the breechblock along the axis of the center of the barrel 's bore. Rimfire cartridges however, must be struck on the base about the rim of the cartridge. While rimfire firearms may use a firing pin with a round cross-section, it is common for them to be flat, with

3780-447: The cocked position when it is pulled to the rear and the trigger is not depressed. In a revolver , this means that simply squeezing the trigger when the hammer is lowered will both cock and release it. If the user uses their thumb to pull the hammer to the back, but does not press the trigger, the mechanism will lock the hammer in the cocked position until the trigger is pressed, just like a single action. Firing in double-action mode allows

3864-536: The design include serration at the front of the slide for easier operation and disassembly, a high "beaver-tail" grip safety , external extractor , lighter weight hammer and trigger, as well as updated internal safeties to prevent accidental discharges if dropped. S&W 1911s are available with black finished carbon steel slides and frames or bead blasted stainless slides and frames. They are also available with aluminum frames alloyed with scandium in either natural or black finishes. These updates have resulted in

3948-608: The factory. A release trigger releases the hammer or striker when the trigger is released by the shooter, rather than when it is pulled. A binary trigger is a trigger for a semiautomatic firearm that drops the hammer both when the trigger is pulled, and also when it is released. Examples include the AR-15 series of rifles, produced by Franklin Armory, Fostech Outdoors, and Liberty Gun Works. The AR-15 trigger as produced by Liberty Gun Works only functions in pull and release mode, and does not have

4032-399: The firing spring acts and the firing pin are separate units. Confusingly, parts lists will often refer to this type of hammer as a "striker". Striker-fired (or similar) bolt action firearms may be classified as cock-on-close or cock-on-open . When the breech is opened and retracted rearward, the striker is also carried rearward so that the striker catch passes over the trigger sear. When

4116-421: The first place. The Taurus PT 24/7 Pro pistol (not to be confused with the first-generation 24/7 which was a traditional pre-set) offered this feature starting in 2006. The Walther P99 Anti-Stress is another example. A double-crescent trigger provides select fire capability without the need for a fire mode selector switch. Pressing the upper segment of the trigger produced semi-automatic fire, while holding

4200-481: The hammer from accidentally dropping, or a " decocker " – a lever that safely and gently drops the hammer (i.e. decocks the gun ) without fear of the gun firing. The latter is the more popular because, without a decocker, the user is forced to lower the hammer by hand onto a loaded chamber, with all of the attendant safety risks that involves, to return the gun to double-action mode. Revolvers almost never feature safeties, since they are traditionally carried un-cocked, and

4284-430: The hammer is manually lowered again. This gives the positive aspects of a single-action trigger without the need to carry "cocked and locked" (with a loaded chamber and cocked hammer), or with an empty chamber, which requires the user to chamber a round before firing. A potential drawback of a DA/SA weapon is that the shooter must be comfortable dealing with two different trigger pulls: the longer, heavier DA first pull and

SECTION 50

#1732869803008

4368-637: The hammer on a loaded chamber, if one only fires a partial magazine. A good example of this action in a semi-automatic is the SIG Sauer DAK trigger, or the DAO action of the Sig P250 . For striker-fired pistols such as the Taurus 24/7 , the striker will remain in the rest position through the entire reloading cycle. This term applies most often to semi-automatic handguns; however, the term can also apply to some revolvers such as

4452-665: The hammer requires the user to physically cock it prior to every shot; unlike a DA/SA gun, which cocks itself every time the slide is cycled. There are many examples of DA/SA semi-automatics, the Little Tom Pistol being the first, followed up by the Walther PPK and Walther P38 . Modern examples include weapons such as the Beretta 92 , among others. Almost all revolvers that are not specified as single-action models are capable of firing in both double- and single-action mode, for example,

4536-424: The hammer – and there are many designs where the trigger is used for a range of other functions. Firearms use triggers to initiate the firing of a cartridge seated within the gun barrel chamber . This is accomplished by actuating a striking device through a combination of mainspring (which stores elastic energy ), a trap mechanism that can hold the spring under tension , an intermediate mechanism to transmit

4620-500: The hammer/striker (and nothing else), while the hammer/striker must be cocked by separate means. Almost all single-shot and repeating long arms (rifles, shotguns , submachine guns , machine guns, etc.) use this type of trigger. The "classic" single-action revolver of the mid-to-late 19th century includes black powder caplock muzzleloaders such as the Colt 1860 "Army" Model , and Colt 1851 "Navy" Model , and European models like

4704-405: The impact force to strike the primer from a spring acting directly upon the firing pin – similar to a crossbow , where the striker (firing pin) is like the crossbow bolt (arrow). A striker mechanism is very common in bolt-action firearms but not to the exclusion of hammer-operated mechanisms. It is also found in other actions where the breechblock reciprocates directly inline with the axis of

4788-465: The late 1930s and early 1940s, Walther introduced the first "double-action" (actually DA/SA hybrid) semi-automatic pistols, the PPK and P.38 models, which featured a revolver-style double-action trigger, allowing the weapon to be carried with a round chambered and the hammer lowered. After the first shot, they would fire subsequent shots like a single-action pistol. These pistols rapidly gained popularity, and

4872-420: The late 19th century, for the first half of the 20th century, all semi-automatic pistols were single-action weapons, requiring the weapon to be carried cocked and loaded with the safety on, or uncocked with an empty chamber ( Colt M1911 , Mauser C96 , Luger P.08 , Tokarev TT , Browning Hi-Power ). The difference between these weapons and single-action revolvers is that while a single-action revolver requires

4956-445: The lower segment of the trigger produced fully automatic fire. Though considered innovative at the time, the feature was eliminated on most firearms due to its complexity. Examples include MG 34 , Kulsprutegevär m/40 automatic rifle , M1946 Sieg automatic rifle , Osario Selectiva, and Star Model Z62 . A progressive , or staged trigger allows different firing rates based on how far it is depressed. For example, when pulled lightly,

5040-415: The optional ability to cock the hammer separately, reducing the trigger to perform just one action. This is opposed to "double-action only" firearms, which completely lack the capability to fire in single-action mode. In a DA/SA trigger, the mechanism is designed with an internal sear that allows the trigger to both cock and release the hammer/striker when fully pulled, or to merely lock the hammer/striker in

5124-412: The primer when the hammer is resting against it. This is a safety measure to prevent discharge from external forces such as a drop. Firing relies upon the transfer of momentum from the hammer to give the firing pin sufficient impact energy to cause firing. The two main types of metallic cartridges used in modern firearms are centerfire and rimfire . In centerfire cartridges, the primer is located in

SECTION 60

#1732869803008

5208-455: The primer. Many revolvers use a firing pin that is fixed to the hammer. Simple blowback sub-machine guns that fire from the open-bolt position often have a fixed firing pin that protrudes from the face of the bolt. As the bolt fully closes on the breech the primer of the newly chambered round is struck, causing the cartridge to fire. The Owen and F1 submachine gun are examples that use bolt-face fixed firing-pins. Some mortars use

5292-543: The primer. Examples of pre-set strikers are the Glock , Smith & Wesson M&P , Springfield Armory XD -S variant (only), Kahr Arms , FN FNS series and Ruger SR series pistols. This type of trigger mechanism is sometimes referred to as a Striker Fired Action or SFA. Examples of pre-set hammers are the Kel-Tec P-32 and Ruger LCP pistols. Pre-set hybrid triggers are similar to a DA/SA trigger in reverse. The first pull of

5376-403: The priming in the sabot. Unlike Pauly's cartridge, which was not widely accepted, Dreyse's rifle was adopted by Prussia as its infantry service rifle . It was the first military breechloader to use a self-contained cartridge and consequently, the first to employ a firing pin. The pinfire cartridge patented in 1835, uses a metallic cartridge with an integrated firing pin located radially near

5460-410: The rear of the firing pin tube within the breechblock is angled away from the centerline of the barrel toward the hammer. The Sharps rifle uses a firing pin block to solve this alignment problem. The block sits within a recess in the breechblock. When struck by the hammer, the whole block is propelled forward. That part of the block with the firing pin sits on the centerline of the barrel and strikes

5544-543: The sear reaches the point of release, which is described as resembling the breaking of rigid materials when the strength fails under stress . The actuation force required to overcome the sear resistance during the break is known as the trigger weight , which is usually measured with a force gauge in newtons in SI units , or alternatively kilograms or grams in metric units, and pounds and/or ounces in US customary units . The break

5628-401: The set trigger, and then pulling the firing trigger. A double set, double phase trigger can be operated as a standard trigger if the set trigger is not pulled, or as a set trigger by first pulling the set trigger. Double set, double phase triggers offer the versatility of both a standard trigger and a set trigger. Pre-set strikers and hammers apply only to semi-automatic handguns. Upon firing

5712-433: The shorter, lighter subsequent SA pulls. The difference between these trigger pulls can affect the accuracy of the crucial first few shots in an emergency situation. Although there is little need for a safety on a DA/SA handgun when carrying it loaded with the hammer down, after the first shots are fired, the hammer will be cocked and the chamber loaded. Thus, most DA/SA guns either feature a conventional safety that prevents

5796-406: The shortest, lightest, and smoothest pull available. The pull is also consistent from shot to shot so no adjustments in technique are needed for proper accuracy. On a single-action revolver, for which the hammer must be manually cocked prior to firing, an added level of safety is present. On a semi-automatic, the hammer will be cocked and made ready to fire by the process of chambering a round, and as

5880-556: The spring under tension when "cocked" and ready to fire. The striker spring is compressed between the striker's shoulder and the rear of the breechblock. A striker may be assembled from several component; however, the stored energy in the striker spring is transferred directly to the striker and then to the primer without any intermediate transfer of energy or momentum. As striker mechanisms combine both functions of hammer and firing pin in one piece, they are generally considered to be mechanically simpler but are more robust in construction than

5964-404: The takeup. Setting the takeup travel (also known as the first stage) to near zero essentially makes the trigger a single-stage trigger. Some single-stage triggers (e.g., Glock Safe Action trigger, Savage AccuTrigger ) have an integral safety with a noticeable spring resistance that can functionally mimic a two-stage trigger. The trigger break is named for the sudden loss of resistance when

6048-411: The traditional single-action-only pistols rapidly lost favor, although they still retain a dedicated following among enthusiasts. Today, a typical revolver or semi-automatic pistol is a DA/SA one, carried in double-action mode but firing most of its shots in single-action mode. A double-action trigger, also known as double-action only (DAO) to prevent confusion with the more common hybrid DA/SA designs,

6132-401: The trigger and the hammer/striker is typically referred to as the sear surface. Variable mechanisms will have this surface directly on the trigger and hammer or have separate sears or other connecting parts. The trigger pull can be divided into three mechanical stages: When considering the practical accuracy of a firearm, the trigger takeup is often considered the least critical stage of

6216-414: The trigger break. It can be a very critical factor for accuracy because shaking movements during this phase may precede the projectile leaving the barrel and is especially important with firearms with long barrels, slow projectiles and heavy trigger weights, where the more significant resistance drop can make the trigger finger overshoot and shake in an uncontrolled fashion. Having some overtravel provides

6300-409: The trigger is pre-set. If the striker or hammer fail to discharge the cartridge, the trigger may be pulled again and will operate as a double-action only (DAO) until the cartridge discharges or the malfunction is cleared. This allows the operator to attempt a second time to fire a cartridge after a misfire malfunction, as opposed to a single-action, in which the only thing to do if a round fails to fire

6384-479: The trigger is tasked to perform, a.k.a. the trigger action (not to be confused with the action of the whole firearm , which refers to all the components that help handle the cartridge, including the magazine , bolt , hammer and firing pin / striker , extractor and ejector in addition to the trigger). While a trigger is primarily designed to set off a shot by releasing the hammer/striker, it may also perform additional functions such as cocking (loading against

6468-431: The trigger pull begins. With semi-automatics, this means that unlike DA/SA weapons, the hammer does not remain cocked after the first round is fired, and every shot is in double-action mode. With revolvers, this means that one does not have the option of cocking the gun before shooting and must always shoot it in double action mode. Although there have been revolvers that were designed with trigger mechanisms totally lacking

6552-409: The trigger pull. Often triggers are classified as either single-stage or two-stage based on the takeup. A single-stage trigger is often called direct trigger and is popular on hunting rifles. A two-stage trigger is often called pressure trigger and is popular on competition rifles. Some fully adjustable triggers can be adjusted to function as either a single-stage or two-stage trigger by adjusting

6636-425: The trigger, and it travels to its resting position. On semiauto firearms the movement eventually passes by reset position where trigger-disconnector mechanism resets itself to its resting state, in which pulling the trigger releases the sear. The reset event does not occur in double action firearms and in full auto firearms. There are numerous types of trigger designs, typically categorized according to which functions

6720-514: The trigger, or by pushing forward on a small lever attached to the rear of the trigger. This takes up the trigger slack (or "take-up") in the trigger and allows for a much lighter trigger pull. This is colloquially known as a hair trigger . A double set trigger achieves the same result, but uses two triggers: one sets the trigger and the other fires the weapon. Double set triggers can be further classified into two different phases. A double set, single phase trigger can only be operated by first pulling

6804-485: The user to manually cock the hammer before each firing, a single-action semi-automatic pistol only requires manual cocking for the first shot, after which the slide will reciprocate under recoil to automatically recock the hammer for a next shot, and is thus always cocked and ready unless the user manually decocks the hammer, encounters a misfiring cartridge , or pulls the trigger on an empty chamber (for older weapons lacking "last round bolt hold open" feature). In

6888-416: The weapon can be carried with the hammer down on a loaded chamber, reducing perceived danger of carrying a single-action semi-automatic. When the user is ready to fire, simply pulling the trigger will cock and release the hammer in double action mode. When the weapon fires, the cycling slide automatically cocks the hammer to the rear, meaning that the rest of the shots fired will be in single-action mode, unless

6972-416: The weapon will fire a single shot. When depressed further, the weapon fires at a fully automatic rate. Examples include FN P90 , Jatimatic , CZ Model 25 , PM-63 , BXP , F1 submachine gun , Vigneron submachine gun , Wimmersperg Spz-kr , and Steyr AUG . Each trigger mechanism has its own merits. Historically, the first type of trigger was the single-action. This is the simplest mechanism and generally

7056-760: Was widely adopted and is used almost exclusively in modern centerfire rifle designs. The Mauser Gewehr 98 , the Mosin–Nagant and M1903 Springfield are examples of service rifles using this type of operation. Modern era guns in general (and not just firearms) use a firing pin of some description to initiate firing. Mechanical contact fuzes in explosive ordnance will employ a firing pin or striker to initiate detonation . Such devices include: artillery projectiles , aerial bombs and land mines . In landmines, non-metallic firing pins, made from ceramics for example, may be used to minimise their magnetic signature . The M127A1 signal rocket (and other similar flares ) have

#7992