22 in (56 cm) 24 in (61 cm)
62-577: The Modular Sniper Rifle , or MSR , is a bolt-action sniper rifle developed and produced by Remington Arms for the United States Army . It was introduced in 2009, and was designed to meet specific United States Army and USSOCOM Precision Sniper Rifle requirements. The MSR initially won the PSR competition, and was called the Remington Mk 21 Precision Sniper Rifle in U.S. military service. However, it
124-412: A spring . When it moves back, the extractor pulls the spent casing of the previous shot from the chamber, and once the case is clear out of the chamber, the ejector kicks the case out of the firearm. When the bolt moves forward, it picks up a new cartridge from the magazine and pushes it into the chamber. A telescoping bolt is a bolt that wraps around the breech end of the barrel. This bolt design
186-460: A "cock on open" system. Although this bolt system has been rarely used in commercial sporting rifles (the Vostok brand target rifles being the most recognized) and has never been exported outside of Russia, although large numbers of military surplus Mosin–Nagant rifles have been sporterized for use as hunting rifles in the following years since the end of World War II. The Swing was developed in 1970 in
248-546: A bolt-action shotgun, albeit one designed to be attached to an M16 rifle or M4 carbine using an underbarrel mount (although with the standalone kit, the MASS can become a standalone weapon). Mossberg 12-gauge bolt-action shotguns were briefly popular in Australia after the 1997 changes to firearms laws , but the shotguns themselves were awkward to operate and had only a three-round magazine, thus offering no practical or real advantages over
310-410: A conventional double-barreled shotgun. Some pistols use a bolt-action system, although this is uncommon, and such examples are typically specialized hunting and target handguns. Most of the bolt-action designs use a rotating bolt (or "turn pull") design, which involves the shooter doing an upward "rotating" movement of the handle to unlock the bolt from the breech and cock the firing pin , followed by
372-469: A firing mechanism without a hammer , but there are some hammer-fired models, such as the Merkel Helix. Firearms using a hammer usually have a comparably longer lock time than hammerless mechanisms. In the sport of biathlon , because shooting speed is an important performance factor and semi-automatic guns are illegal for race use, straight pull actions are quite common and are used almost exclusively in
434-580: A gravity-operated tubular magazine in the stock. Another more well-known bolt-action repeating rifle was the Vetterli rifle of 1867 and the first bolt-action repeating rifle to use centerfire cartridges was the weapon designed by the Viennese gunsmith Ferdinand Fruwirth in 1871. Ultimately, the military turned to bolt-action rifles using a box magazine ; the first of its kind was the M1885 Remington–Lee , but
496-607: A metallic cartridge's powder charge – were invented in the 1860s as well, the Berdan and the Boxer systems. The United States purchased 900 Greene rifles (an under hammer, percussion capped, single-shot bolt-action that used paper cartridges and an ogival bore rifling system) in 1857, which saw service at the Battle of Antietam in 1862, during the American Civil War ; however, this weapon
558-583: A rearward "pull" to open the breech, extract the spent cartridge case, then reverse the whole process to chamber the next cartridge and relock the breech. There are four major turn bolt-action designs: the Remington M-700 , possibly the single most numerous produced rifle in history which is now also used as basis for most custom competition rifle actions, along with the Mauser system, the Lee–Enfield system, and
620-401: A rigid type of bolt lock. Semi-rigid bolt locks have their locking elements movably mounted on either the bolt, barrel or breech housing and using a bolt carrier. Examples of semi-rigid bolt locks are roller-locked bolts, or ball bearings as on Heym SR 30 or Anschütz 1827 Fortner (both straight-pull rifles ). In a closed bolt firearm, the bolt is in its foremost position upon firing. This
682-471: A rotating bolt design. Johann Nicholas von Dreyse 's rifle of 1838 was accepted into service by Prussia in 1841, which was in turn developed into the Prussian Model in 1849. The design was a single shot breech-loader and had the now familiar arm sticking out from the side of the bolt, to turn and open the chamber . The entire reloading sequence was a more complex procedure than later designs, however, as
SECTION 10
#1733085613317744-505: A separate bolthead that rotates with the bolt and the bearing lugs, in contrast to the Mauser system where the bolthead is a non-removable part of the bolt. The Mosin–Nagant is also unlike the Lee–Enfield system where the bolthead remains stationary and the bolt body itself rotates. The Mosin–Nagant bolt is a somewhat complicated affair, but is extremely rugged and durable; like the Mauser, it uses
806-430: A single lethal shot from a safe distance. Target shooters favour single-shot bolt actions for their simplicity of design, reliability, and accuracy. Bolt-action shotguns are considered a rarity among modern firearms but were formerly a commonly used action for .410 entry-level shotguns, as well as for low-cost 12- gauge shotguns. The M26 Modular Accessory Shotgun System (MASS) is the most recent and advanced example of
868-529: A specific weapon's type of action. However, both straight pull and rotating bolt rifles are types of bolt-action rifles. Lever-action and pump-action weapons must still operate the bolt, but they are usually grouped separately from bolt-actions that are operated by a handle directly attached to a rotating bolt. Early bolt-action designs, such as the Dreyse needle gun and the Mauser Model 1871 , locked by dropping
930-757: A trigger derived from the Finnish Mantari, the Swing was commercially successful, with the basic design reused in the Paramount, RPA Quadlock and Millenium rifles. The Vetterli rifle was the first bolt-action repeating rifle introduced by an army. It was used by the Swiss army from 1869 to circa 1890. Modified Vetterlis were also used by the Italian Army . Another notable design is the Norwegian Krag–Jørgensen , which
992-415: Is often used to reduce overall weapon length without sacrificing barrel length or bolt weight. A turn bolt refers to a firearm component where the whole bolt without using a bolt carrier turns to lock/unlock. This is mostly used to describe manually operated bolt action firearms, but also on some automatic firearms. The most common locking mechanism on rifles is a rotating bolt , which can be classified as
1054-515: Is that it is usually loaded by hand, one round at a time, although a box-like device was made that could drop five rounds into the magazine, all at once via a stripper or en bloc clip. This made it slower to reload than other designs which used stripper or en bloc clips. Another historically important bolt-action system was the Gras system, used on the French Mle 1874 Gras rifle , Mle 1886 Lebel rifle (which
1116-413: Is the straight-pull mechanism, where no upward handle-turning is needed and the bolt unlocks automatically when the handle is pulled rearwards by the user's hand. The first bolt-action rifle was produced in 1824 by Johann Nikolaus von Dreyse , following work on breechloading rifles that dated to the 18th century. Von Dreyse would perfect his Nadelgewehr (Needle Rifle) by 1836, and it was adopted by
1178-487: Is the most common bolt-action system in the world, being in use in nearly all modern hunting rifles and the majority of military bolt-action rifles until the middle of the 20th century. The Mauser system is stronger than that of the Lee–Enfield system, due to two locking lugs just behind the bolt head, which make it better able to handle higher-pressure cartridges (i.e. magnum cartridges ). The 9.3×64mm Brenneke and 8×68mm S magnum rifle cartridge "families" were designed for
1240-516: The Biathlon World Cup . The first company to make the straight pull action for .22 caliber was J. G. Anschütz ; Peter Fortner junior designed the "Fortner Action", which was incorporated into the Anschütz 1827 Fortner . The Fortner action is specifically the straight-pull ball bearing lock action, which features spring-loaded ball bearings on the side of the bolt which lock into a groove inside
1302-557: The Mosin–Nagant system. All four differ in the way the bolt fits into the receiver, how the bolt rotates as it is being operated, the number of locking lugs holding the bolt in place as the gun is fired, and whether the action is cocked on the opening of the bolt (as in both the Mauser system and the Mosin Nagant system) or the closing of the bolt (as in the Lee–Enfield system). The vast majority of modern bolt-action rifles were made for
SECTION 20
#17330856133171364-569: The Prussian Army in 1841. While it saw limited service in the German Revolutions of 1848 , it was not fielded widely until the 1864 victory over Denmark . In 1850 a metallic centerfire bolt-action breechloader was patented by Béatus Beringer. In 1852 another metallic centerfire bolt-action breechloader was patented by Joseph Needham and improved upon in 1862 with another patent. Two different systems for primers –the mechanism to ignite
1426-456: The firing pin had to be independently primed and activated, and the lever was used only to move the bolt. [REDACTED] Media related to Bolt action (firearms) at Wikimedia Commons Bolt (firearms) A bolt is the part of a repeating , breechloading firearm that blocks the rear opening (breech) of the barrel chamber while the propellant burns, and moves back and forward to facilitate loading/unloading of cartridges from
1488-402: The magazine . The firing pin and extractor are often integral parts of the bolt. The terms " breechblock " and "bolt" are often used interchangeably or without a clear distinction, though usually, a bolt is a type of breechblock that has a nominally circular cross-section. In most automatic firearms that use delayed blowback , recoil , or gas operation , the bolt itself is housed within
1550-853: The rate of fire of the gun. In 1993, the German Blaser company introduced the Blaser R93 , a new straight pull action where locking is achieved by a series of concentric "claws" that protrude/retract from the bolthead, a design that is referred to as Radialbundverschluss ("radial connection"). As of 2017 the Rifle Shooter magazine listed its successor Blaser R8 as one of the three most popular straight pull rifles together with Merkel Helix and Browning Maral. Some other notable modern straight pull rifles are made by Beretta , C.G. Haenel , Chapuis , Heym , Lynx , Rößler , Savage Arms , Strasser, and Steel Action. Most straight bolt rifles have
1612-424: The striker within the bolt (either on opening or closing of the bolt depending on the gun design) and engages it against the sear . When the bolt is returned to the forward position, a new cartridge (if available) is pushed out of the magazine and into the barrel chamber , and finally the breech is closed tight by rotating the handle down so the bolt head relocks on the receiver. A less common bolt-action type
1674-504: The 7.62mm NATO M40A5. The Remington MSR is a manually operated bolt-action weapon with a rotary locking bolt. To facilitate caliber change, the bolt is equipped with removable bolt heads, with bolt faces matched for appropriate calibers. Bolt heads have three radial locking lugs. The MSR rifle is built upon an aluminum alloy "chassis", which hosts a compact receiver, adjustable trigger unit, pistol grip, and fully adjustable side-folding buttstock. The quick-change barrels are free-floated inside
1736-522: The M10 and No 4 Mk IV rifles manufactured by Australian International Arms. Rifle Factory Ishapore of India manufactures a hunting and sporting rifle chambered in .315 which also employs the Lee Enfield action. The Mosin–Nagant action, created in 1891 and named after the designers Sergei Mosin and Léon Nagant , differs significantly from the Mauser and Lee–Enfield bolt-action designs. The Mosin–Nagant design has
1798-529: The Mauser M 98 bolt-action. A novel safety feature was the introduction of a third locking lug present at the rear of the bolt that normally did not lock the bolt, since it would introduce asymmetrical locking forces. The Mauser system features "cock on opening", meaning the upward rotation of the bolt when the rifle is opened cocks the action. A drawback of the Mauser M 98 system is that it cannot be cheaply mass-produced very easily. Many Mauser M 98-inspired derivatives feature technical alterations, such as omitting
1860-530: The Mk 21 PSR to effectively engage targets out to 1,500 m (1,640 yd). The main objective is for the rifle to defeat level IV body armor at 400 meters, whether suppressed or unsuppressed, in temperature ranges of −65 to 160 °F (−54 to 71 °C). Other minimum requirements include a projectile velocity of 1,340 ft/s (410 m/s) or more at 1,250 m (1,367 yd), 1,000 ft⋅lb (1,356 J) of kinetic energy at 1,500 m (1,640 yd), and
1922-527: The PSR competition is a modified version of the original MSR. It can be chambered in 7.62×51mm NATO , .300 Winchester Magnum , and .338 Lapua Magnum . It is reported to have 0.7 MOA average accuracy at 1,000 m (1,094 yd) with both Barnes and ATK 300 gr (19.4 g) .338 Lapua Magnum ammunition. Changes to the PSR version include: On 14 August 2014, the Army announced it was seeking sources to produce .338 Lapua armor-piercing (AP) ammunition for use in
Remington MSR - Misplaced Pages Continue
1984-429: The U.S. Army was considering the PSR to replace both the .300 Winchester Magnum M2010 Enhanced Sniper Rifle and the .50 BMG M107 Long Range Sniper Rifle for regular snipers, although no decision has been made. The U.S. Marine Corps was also considering the Mk 21 to replace their M40A5 sniper rifle , but is unlikely to adopt the Mk 21 due to the higher cost of the system, particularly the ammunition, as compared to
2046-604: The United Kingdom as a purpose-built target rifle for use in NRA competition. Fullbore target rifle competitions historically used accurised examples of the prevailing service rifle, but it was felt these had reached the end of their development potential. The Swing bolt featured four lugs on the bolt head, at 45 degrees when closed - splitting the difference between the vertically locking Mauser and horizontally locking Enfield bolt designs. Supplied with Schultz & Larsen barrels and
2108-807: The ability to defeat both 3 ⁄ 8 in (9.5 mm) of rolled homogeneous armor (RHA) and 1 ⁄ 2 in (12.7 mm) of cast iron at 800 m (875 yd). Bolt-action Bolt-action is a type of manual firearm action that is operated by directly manipulating the bolt via a bolt handle , most commonly placed on the right-hand side of the firearm (as most users are right-handed ). The majority of bolt-action firearms are rifles , but there are also some variants of shotguns and handguns that are bolt-action. Bolt-action firearms are generally repeating firearms , but many single-shot designs are available particularly in shooting sports where single-shot firearms are mandated, such as most Olympic and ISSF rifle disciplines. From
2170-472: The bolt ahead of the lugs may flex on firing which, although a safety advantage with repeated firing over time, this may lead to a stretched receiver and excessive headspacing, which if perceived as a problem can be remedied by changing the removable bolt head to a larger sized one (the Lee–Enfield bolt manufacture involved a mass production method where at final assembly the bolt body was fitted with one of three standard size bolt heads for correct headspace ). In
2232-462: The bolt cocks the action. This enables a shooter to keep eyes on sights and targets uninterrupted when cycling the bolt. The ability of the bolt to flex between the lugs and chamber, which also keeps the shooter safer in case of a catastrophic chamber overpressure failure. The disadvantage of the rearward-located bolt lugs is that a larger part of the receiver, between chamber and lugs, must be made stronger and heavier to resist stretching forces. Also,
2294-462: The bolt handle or bolt guide rib into a notch in the receiver , this method is still used in .22 rimfire rifles. The most common locking method is a rotating bolt with two lugs on the bolt head, which was used by the Lebel Model 1886 rifle , Model 1888 Commission Rifle , Mauser M 98 , Mosin–Nagant and most bolt-action rifles. The Lee–Enfield has a lug and guide rib, which lock on the rear end of
2356-407: The bolt in addition to the linear motions to perform chambering and primary extraction . The bolt locking of a straight pull action is achieved differently without needing manual inputs, therefore the entire operating cycle needs the shooter to perform only two movements (pull back and push forward), instead of four movements (rotate up, pull back, push forward, and rotate down), this greatly increases
2418-432: The bolt in place. The operation can be done via a rotating bolt , a lever, cam action, a locking piece, or a number of systems. Straight pull designs have seen a great deal of use, though manual turn bolt designs are what is most commonly thought of in reference to a bolt-action design due to the type ubiquity. As a result, the bolt-action term is often reserved for more modern types of rotating bolt designs when talking about
2480-409: The bolt into the receiver. The bolt knob is the part of the bolt handle that the user grips when loading and reloading the firearm and thereby acts as a cocking handle . On many older firearms, the bolt knob is welded to the bolt handle, and as such becoming an integral part of the bolt handle itself. On many newer firearms, the bolt knob is instead threaded onto the handle, allowing the user to change
2542-440: The bolt is held fixed by its locking lugs during firing, forcing all the expanding gas forward. It is manually unlocked and moved to extract the spent casing and chamber another round. In a self-loading firearm ( semi-automatic , burst fire , or fully-automatic ), the bolt cycles back and forward between each shot, propelled back by recoil ( recoil operation ) or the expanding gas ( blowback and gas operation ) and forward by
Remington MSR - Misplaced Pages Continue
2604-420: The bolt's housing. With the new design came a new dry fire method; instead of the bolt being turned up slightly, the action is locked back to catch the firing pin. The action was later used in the centre-fire Heym SR 30 . Typically, the bolt consists of a tube of metal inside of which the firing mechanism is housed, and which has at the front or rear of the tube several metal knobs, or "lugs", which serve to lock
2666-473: The commercial market post-war, numbering in the tens of millions by Remington in the unique, and most accurate Model 700, two of the others use the Mauser system, with other designs such as the Lee–Enfield system and the Mosin Nagant system, of only limited usage. The Mauser bolt-action system is based on 19th-century Mauser bolt-action rifle designs and was finalized in the Gewehr 98 designed by Paul Mauser . It
2728-413: The design's inherent potential for superior accuracy and precision , as well as ruggedness and reliability compared to self-loading designs. Most bolt-action firearms use a rotating bolt operation, where the handle must first be rotated upward to unlock the bolt from the receiver , then pulled back to open the breech and allowing any spent cartridge case to be extracted and ejected. This also cocks
2790-451: The existing bolt handle. These are often made of either rubber or plastic. Most bolt-action firearms are fed by an internal magazine loaded by hand, by en bloc , or by stripper clips , though a number of designs have had a detachable magazine or independent magazine, or even no magazine at all, thus requiring that each round be independently loaded. Generally, the magazine capacity is limited to between two and ten rounds, as it can permit
2852-414: The faster rate of fire that all semi-automatic rifle alternatives allow. There are, however, many semi-automatic rifle designs used especially in the designated marksman role. Today, bolt-action rifles are chiefly used as hunting and target rifles. These rifles can be used to hunt anything from vermin to deer and to large game , especially big game caught on a safari , as they are adequate to deliver
2914-473: The first to be generally adopted was the British 1888 Lee–Metford . World War I marked the height of the bolt-action rifle's use, with all of the nations in that war fielding troops armed with various bolt-action designs. During the buildup prior to World War II , the military bolt-action rifle began to be superseded by semi-automatic rifles and later fully automatic rifles , though bolt-action rifles remained
2976-412: The larger bolt carrier group (BCG), which contains additional parts that receives rearward push from a gas tube ( direct impingement ) or a gas piston (short-stroke or long-stroke piston) system. The slide of a self-loading pistol contains the same components and serves similar functions. In manually operated firearms, such as bolt-action , lever-action , and pump-action rifles or shotguns ,
3038-682: The late 19th century all the way through both World Wars , bolt-action rifles were the standard infantry service weapons for most of the world's military forces, with the exception of the United States Armed Forces , who used the M1 Garand Semi-automatic rifle . In modern military and law enforcement after the Second World War, bolt-action firearms have been largely replaced by semi-automatic and selective-fire firearms, and have remained only as sniper rifles due to
3100-461: The magazine to be flush with the bottom of the rifle, reduce the weight, or prevent mud and dirt from entering. A number of bolt-actions have a tube magazine , such as along the length of the barrel. In weapons other than large rifles, such as pistols and cannons , there were some manually operated breech-loading weapons. However, the Dreyse Needle fire rifle was the first breech loader to use
3162-560: The metallic cartridge bolt-action Gras rifle in 1874. European armies continued to develop bolt-action rifles through the latter half of the 19th century, first adopting tubular magazines as on the Kropatschek rifle and the Lebel rifle . The first bolt-action repeating rifle was patented in Britain in 1855 by an unidentified inventor through the patent agent Auguste Edouard Loradoux Bellford using
SECTION 50
#17330856133173224-835: The original bolt knob for an aftermarket one, either for aesthetical reasons, achieving better grip or similar. The type of threads used vary between firearms. European firearms often use either M6 1 or M8 1.25 threads, for example M6 is used on the SIG Sauer 200 STR , Blaser R93 , Blaser R8 , CZ 457 and Bergara rifles, while M8 is used on the Sako TRG and SIG Sauer 404 . Many American firearms instead use 1/4" 28 TPI (6.35 0.907 mm) or 5/16" 24 TPI (7.9375 1.058 mm) threads. Some other thread types are also used, for example, No. 10 32 TPI (4.826 0.794 mm) as used by Mausingfield. There also exists aftermarket slip-on bolt handle covers which are mounted without having to remove
3286-469: The primary weapon of most of the combatants for the duration of the war; and many American units, especially the USMC , used bolt-action M1903 Springfield rifles until sufficient numbers of M1 Garand rifles were made available. The bolt-action is still common today among many sniper rifles , as the design has the potential for superior accuracy, reliability, reduced weight, and the ability to control loading over
3348-580: The third locking lug and feature a "cock on closing" operation. The Lee–Enfield bolt-action system was introduced in 1889 with the Lee–Metford and later Lee–Enfield rifles (the bolt system is named after the designer James Paris Lee and the barrel rifling after the Royal Small Arms Factory in the London Borough of Enfield ), and is a "cock on closing" action in which the forward thrust of
3410-538: The third safety locking lug, to simplify production. The controlled-feed on the Mauser M 98 bolt-action system is simple, strong, safe, and well-thought-out design that has inspired other military and sporting rifle designs that became available during the 20th century, including the: Versions of the Mauser action designed prior to the Gewehr 98's introduction, such as that of the Swedish Mauser rifles and carbines, lack
3472-424: The tubular handguard which is provided with a number of user-installable Picatinny type accessory rails. The top of the receiver also is fitted with a monolithic Picatinny rail used to install sighting equipment (telescope sights or night vision sights). Additional equipment includes a detachable folding bipod and a quick-detachable suppressor which installs over the specially designed muzzle brake. The model that won
3534-406: The years leading up to World War II, the Lee–Enfield bolt system was used in numerous commercial sporting and hunting rifles manufactured by such firms in the United Kingdom as BSA, LSA, and Parker–Hale, as well as by SAF Lithgow in Australia. Vast numbers of ex-military SMLE Mk III rifles were sporterised post WWII to create cheap, effective hunting rifles, and the Lee–Enfield bolt system is used in
3596-501: Was followed by a $ 79.7 million contract for 5,150 rifles with suppressors, along with 4,696,800 rounds of ammunition to be supplied over the next ten years. The contract was awarded on 12 September 2013. Remington Defense produces the sniper rifles and utilizes two other companies for other system components, with Barnes Bullets for ammunition and Advanced Armament Corporation for muzzle brakes and suppressors; all three companies are subsidiaries of Freedom Group Incorporated . In 2015,
3658-462: Was the first to introduce ammunition loaded with nitrocellulose-based smokeless powder ), and the Berthier series of rifles. Straight-pull bolt-actions differ from conventional turn-pull bolt-action mechanisms in that the bolt can be cycled back and forward without rotating the handle and thus only a linear motion is required, as opposed to a traditional bolt-action, where the user has to axially rotate
3720-566: Was then decided that the Mk 21 did not conform to SOCOM requirements at the time in 2018, and the program was re-competed with the Barrett MRAD selected in 2019 as the Mk 22 Advanced Sniper Rifle solution. On 7 March 2013, MSR was declared the winner of the Precision Sniper Rifle competition. Remington announced that the MSR had won on March 8, and it was publicly confirmed on March 9. This
3782-574: Was ultimately considered too complicated for issue to soldiers and was supplanted by the Springfield Model 1861 , a conventional muzzle loading rifle. During the American Civil War, the bolt-action Palmer carbine was patented in 1863, and by 1865, 1000 were purchased for use as cavalry weapons. The French Army adopted its first bolt-action rifle, the Chassepot rifle , in 1866 and followed with
SECTION 60
#17330856133173844-628: Was used by Norway, Denmark, and briefly the United States. It is unusual among bolt-action rifles in that is loaded through a gate on the right side of the receiver, and thus can be reloaded without opening the bolt. The Norwegian and Danish versions of the Krag have two locking lugs, while the American version has only one. In all versions, the bolt handle itself serves as an emergency locking lug. The Krag's major disadvantage compared to other bolt-action designs
#316683