A sailboat or sailing boat is a boat propelled partly or entirely by sails and is smaller than a sailing ship . Distinctions in what constitutes a sailing boat and ship vary by region and maritime culture.
64-494: The Nordic Folkboat is a sailboat that was designed by Scandinavian Sailing Federation as a racer - cruiser and first built in 1942. Tord Sundén was hired by the Scandivian Sailing Federation to finalize the plans based on four awarded entries in the design competition. The awarded designs were done by Knud Olsen, Jac M. Iversen, Alfons Kvarnström, and O.W. Dahlström. No winning design was declared. Tord Sundén
128-647: A choice, these factors should be noted: Large outboards are affixed to the transom using clamps and are either tiller steered or controlled from the helm. Generally motors of 100 hp plus are linked to controls at the helm. These range from 2-, 3-, and 4-cylinder models generating 15 to 135 horsepower (11 to 101 kW) suitable for hulls up to 17 feet (5.2 m) in length to powerful V6 and V8 cylinder blocks rated up to 627 hp (468 kW)., with sufficient power to be used on boats of 37 feet (11 m) or longer. Small outboard motors, up to 15 horsepower (11 kW) or so, are easily portable. They are affixed to
192-455: A closed-loop cooling system with a heat exchanger. This means saltwater is not pumped through the engine block, as is the case with most outboard motors, but instead engine coolant and outside water are pumped through (opposite sides of) the heat exchanger. An outboard engine may stall if it does not have the correct inputs. Common problems that lead to stalling are electrical issues, low quality gas or clogged fuel filer. Other issues may include
256-537: A conservative sail-area displacement ratio of 16.28. The length-to-beam ratio was just under 3.5. The four-foot draft appealed to the shoalwater challenged. Headroom was ideal for those wonderful creatures of Scandinavian folklore: elves." Dieter Loibner described the boat in Soundings in 2017 as "a descendant of the sturdy Viking ships, a wind's bride that knows how to handle Erasmus’ moods". Danish sailor, Paul Elvstrøm , said "At first nobody seemed to like them. It took
320-435: A conventional propeller. The frame that holds the motor has a short, swiveling steel pin/tube approximately 15 cm long underneath, to be inserted into a corresponding hole on the transom, or a solid block or wood purposely built-in thereof. This drop-in arrangement enables extremely quick transfer of the motor to another boat or for storage – all that is needed is to lift it out. The pivoting design allows
384-450: A crane and are typically stepped on the keel through any cabin or other superstructure. Many sailboats have an alternate means of propulsion, in case the wind dies or where close maneuvering under sail is impractical. The smallest boats may use a paddle ; bigger ones may have oars ; still others may employ an outboard motor , mounted on the transom; still others may have an inboard engine . Outboard motor An outboard motor
448-520: A cut-away forefoot. Typical versions displace 4,255 lb (1,930 kg) and carry 2,205 lb (1,000 kg) of iron ballast. The boat has a draft of 3.92 ft (1.19 m) with the standard keel and may be fitted with a small outboard motor for docking and manoeuvring. Some boats have sleeping accommodations for cruising, while others have minimal interiors, optimized for lightness for racing. Cruising-equipped boats often have sleeping accommodation for four people, with two main cabin bunks and
512-489: A damaged carburetor oil switch. In Vietnam and other parts of southeast Asia long-tail boats use outboard motors altered to extend their propellers far from the rest of the motor. In Vietnam these outboards are called máy đuôi tôm ( shrimp tail motor ), which are smallish air-cooled or water-cooled gasoline, diesel or even modified automotive engines bolted to a welded steel tube frame, with another long steel tube up to 3 m long to hold an extended drive shaft driving
576-689: A different method of DI. Fuel economy on both direct-injected and four-stroke outboards measures from a 10 percent to 80 percent improvement compared with conventional two-strokes. However, the gap between two-stroke and four-stroke outboard fuel economy is beginning to narrow. Two-stroke outboard motor manufacturers have recently introduced technologies that help to improve two-stroke fuel economy. In 2012, Lehr inc. introduced some small (<5 hp) outboards based on modified Chinese petrol engines to run on propane gas. Tohatsu currently also produces propane powered models, all rated 5 hp. Conversion of larger outboards to run on Liquified petroleum gas
640-428: A forward "V"-berth. The design has a Portsmouth Yardstick DP-N racing average handicap of 103.2 and is usually raced by two to four sailors . Numerous variants of the basic design have been built. The hull shape was largely retained, with variants being built in fibreglass, with new cabin and deck layouts and sometimes a revised keel shape. The boat is supported by an active class club that organizes racing events,
704-407: A jib. Most modern designs have only one sail, the mainsail; however, the traditional catboat could carry multiple sails from the gaff rig. Catboat is a charming and distinctive sailboat featuring a single mast with a single large sail, known as a gaff-rigged sail, and a broad beam that ensures stability. This type of vessel, named after the "cat" tackle used in sailing, has a rich history dating back to
SECTION 10
#1733084880932768-431: A lot of weight in two "wings" which run sideways from the main part of the keel. Even more recent is the concept of canting keels , designed to move the weight at the bottom of a sailboat to the upwind side, allowing the boat to carry more sails. A twin keel has the benefit of a shallower draft and can allow the boat to stand on dry land. Multihulls, on the other hand, have minimal need for such ballast, as they depend on
832-429: A pin called a topper tilt lock. Ventilation is a phenomenon that occurs when surface air or exhaust gas (in the case of motors equipped with through-hub exhaust) is drawn into the spinning propeller blades. With the propeller pushing mostly air instead of water, the load on the engine is greatly reduced, causing the engine to race and the propeller to spin fast enough to result in cavitation , at which point little thrust
896-411: A reduced draft, with a much reduced underwater profile. This, in turn, results directly in reduced wetted surface area and drag. Without a ballast keel, multihulls can go in shallow waters where monohulls can not. There are trade-offs, however, in multihull design. A well designed ballasted boat can recover from a capsize, even from turning over completely. Righting a multihull that has gotten upside down
960-516: A vee-berth forward, with camping gear used for cooking. There are lockers. The interiors are apt to vary widely, with some minimized for racing, and others adapted for cruising." A review in Classic Boat magazine by Steffan Meyric-Hughes wrote, "it has been described as a nautical Volkswagen Beetle. It has been hailed as a rare example of a good thing designed by a committee. But it's more: the Folkboat
1024-504: A while for people to figure out how seaworthy these boats actually are and how well they perform when it is rough." Similar length sailboats Sailboat Although sailboat terminology has varied across history, many terms have specific meanings in the context of modern yachting . A great number of sailboat-types may be distinguished by size, hull configuration, keel type, purpose, number and configuration of masts , and sail plan . Popular monohull designs include: The cutter
1088-404: Is a propulsion system for boats , consisting of a self-contained unit that includes engine, gearbox and propeller or jet drive , designed to be affixed to the outside of the transom . They are the most common motorised method of propelling small watercraft. As well as providing propulsion, outboards provide steering control, as they are designed to pivot over their mountings and thus control
1152-421: Is a recreational keelboat, that was initially built using wooden clinker construction . It was later produced in fibreglass, with wooden trim, with the fibreglass hull simulating the clinker board construction. It has a fractional sloop rig with wooden spars. The hull has a spooned, raked stem , a sharply angled transom , a keel -mounted rudder controlled by a tiller and a fixed modified long keel , with
1216-467: Is available as an option on most outboard motors. Although less efficient than an open propeller, they are particularly useful in applications where the ability to operate in very shallow water is important. They also eliminate the laceration dangers of an open propeller. Propane outboard motors are available from several manufacturers. These products have several advantages such as lower emissions, absence of ethanol-related issues, and no need for choke once
1280-482: Is considered unusual and exotic although some hobbyists continue to experiment. It is important to select a motor that is a good match for the hull in terms of power and shaft length. Whether using a displacement or planing vessel, one should select an appropriate power level; too much power is wasteful (adding unnecessary weight), and may often be dangerous. Boats built in the US have Coast Guard Rating Plates , which specify
1344-489: Is difficult in any case and impossible without help unless the boat is small or carries special equipment for the purpose. Multihulls often prove more difficult to tack, since the reduced weight leads directly to reduced momentum, causing multihulls to more quickly lose speed when headed into the wind. Also, structural integrity is much easier to achieve in a one piece monohull than in a two or three piece multihull whose connecting structure must be substantial and well connected to
SECTION 20
#17330848809321408-461: Is easier for a short-handed crew to manage. A yawl is similar to a ketch, with a shorter mizzen mast carried astern the rudderpost more for balancing the helm than propulsion. Traditional sailboats are monohulls , but multi-hull catamarans and trimarans are gaining popularity. Monohull boats generally rely on ballast for stability and usually are displacement hulls. This stabilizing ballast can, in boats designed for racing, be as much as 50% of
1472-438: Is generated at all. The condition continues until the prop slows enough for the air bubbles to rise to the surface. The primary causes of ventilation are: motor mounted too high, motor trimmed out excessively, damage to the antiventilation plate, damage to propeller, foreign object lodged in the diffuser ring. If the helmsman goes overboard, the boat may continue under power but uncontrolled, risking serious or fatal injuries to
1536-436: Is similar to a sloop with a single mast and mainsail, but generally carries the mast further aft to allow for a jib and staysail to be attached to the head stay and inner forestay, respectively. Once a common racing configuration, today it gives versatility to cruising boats, especially in allowing a small staysail to be flown from the inner stay in high winds. A catboat has a single mast mounted far forward and does not carry
1600-508: Is that if the impeller is run dry for a length of time (such as leaving the engine running when pulling the boat out of the water or in some cases tilting the engine out of the water while running), the impeller is likely to be ruined in the process. Air-cooled outboard engines are currently produced by some manufacturers. These tend to be small engines of less than 5 horsepower (3.7 kW). Outboard engines made by Briggs & Stratton are air-cooled. Outboards manufactured by Seven Marine use
1664-516: Is the angle of the motor in relation to the hull, as illustrated below. The ideal trim angle is the one in which the boat rides level, with most of the hull on the surface instead of plowing through the water. [REDACTED] [REDACTED] [REDACTED] If the motor is trimmed out too far, the bow will ride too high in the water. With too little trim, the bow rides too low. The optimal trim setting will vary depending on many factors including speed, hull design, weight and balance, and conditions on
1728-510: Is the most popular, successful and influential sailing yacht of all time. It comes in various guises and has spawned several derivatives, but the Nordic Folkboat is the original." A review by Theo Rye in Classic Boat said, "she has seakindly manners that punch far above her modest weight, and her deep cockpit and nicely balanced feel on the helm all add up to a simple but satisfying boat to really sail." Practical Sailor magazine described
1792-421: Is the sloop, which features one mast and two sails, typically a Bermuda rigged main , and a headsail . This simple configuration is very efficient for sailing into the wind. A fractional rigged sloop has its forestay attached at a point below the top of the mast, allowing the mainsail to be flattened to improve performance by raking the upper part of the mast aft by tensioning the backstay. A smaller headsail
1856-501: Is typically used: Electric outboard motors are self-contained propulsory units for boats , first invented in 1973 by Morton Ray of Ray Electric Outboards. These are not to be confused with trolling motors , which are not designed as a primary source of power. Most electric outboard motors have 0.5- to 4- kilowatt direct-current (DC) electric motors , operated at 12 to 60 volts DC. Recently developed outboard motors are powered with an alternating current (AC) or DC electric motor in
1920-469: Is what prevents leeway and allows sailing towards the wind. This can be an external piece or a part of the hull. Most monohulls larger than a dinghy require built-in ballast . Depending on the design of the boat, ballast may be 20 to 50 percent of the displacement. The ballast is often integrated into their keels as large masses of lead or cast iron. This secures the ballast and gets it as low as possible to improve its effectiveness. External keels are cast in
1984-476: The Bay of Kiel . Salén promoted the competition and it attracted 58 designs. The judges could not decide on a winner, instead naming six boats as all having some good attributes. As a young naval architect , Sundén was tasked by Salén with taking the best features of each design and drawing plans for a new boat that incorporated them all in the new design. The plans were published without a designer credited. Construction of
Nordic Folkboat - Misplaced Pages Continue
2048-798: The Nordic Folkboat International Association . It has national branches in Sweden, Denmark, Germany and Australia. There are also fleets in Finland, Latvia, Estonia and the San Francisco Bay area of the United States. By 1994, 110 boats were reportedly being sailed in the US. In a 1994 review Richard Sherwood wrote, "the boat is noted for its seaworthy character. With an iron keel, it has raced in winds of 40 knots and often carries full sail in 20-25. Most boats have two bunks, and perhaps
2112-407: The transom is an important factor in achieving optimal performance. The motor should be as high as possible without ventilating or loss of water pressure. This minimizes the effect of hydrodynamic drag while underway, allowing for greater speed. Generally, the antiventilation plate should be about the same height as, or up to two inches higher than, the keel , with the motor in neutral trim. Trim
2176-489: The 19th century in the coastal regions of the United States, particularly New England, where it was widely used by fishermen and sailors. With its straightforward design and uncomplicated rigging, the catboat offers a straightforward and laid-back sailing experience, making it an ideal choice for beginners and pleasure sailors alike. Even today, catboats continue to be cherished by enthusiasts who appreciate their heritage and enjoy their picturesque appearance while cruising through
2240-428: The boat in 2010, saying, "the Nordic Folkboat, a clinker-built sloop with a reverse transom, a spoon bow, and a low cabin that gave it simple but pretty lines. Its long keel, slack bilges, barn-door rudder, and hefty ballast ratio (just over 50 percent) equipped it for North Sea adventures. The cockpit however—because it was not self-bailing—raised the risk quotient for any offshore ambitions. The 7/8-fractional rig gave it
2304-571: The boat is built by Haubold Yachting in Germany . In 1941, while most of Europe was immersed in the Second World War , Sweden was neutral. The Royal Swedish Sailing Association decided to hold a competition to choose a design for a new keelboat , with the support of Swedish shipping magnate Sven Salén , who had won a sailing bronze medal in the Six Meter class at the 1936 Summer Olympics held on
2368-426: The boat via clamps and thus easily moved from boat to boat. These motors typically use a manual start system , with throttle and gearshift controls mounted on the body of the motor, and a tiller for steering. The smallest of these weigh as little as 12 kilograms (26 lb), have integral fuel tanks, and provide sufficient power to move a small dinghy at around 8 knots (15 km/h; 9.2 mph) This type of motor
2432-481: The bottom end in a receptacle that is supported above the keel of the boat or on the deck or other superstructure that allows the mast to be raised at a hinge point until it is erect. Some masts are supported solely at the keel and laterally at the deck and are called "unstayed". Most masts rely in part or entirely (for those stepped on the deck) on standing rigging , supporting them side-to-side and fore-and aft to hold them up. Masts over 25 feet (7.6 m) may require
2496-447: The direction of thrust. The skeg also acts as a rudder when the engine is not running. Unlike inboard motors , outboard motors can be easily removed for storage or repairs. In order to eliminate the chances of hitting bottom with an outboard motor, the motor can be tilted up to an elevated position either electronically or manually. This helps when traveling through shallow waters where there may be debris that could potentially damage
2560-527: The first boat was commenced at Arendals yard in Gothenburg in October 1941 and was launched the next spring, on 23 April 1942. Sundén later claimed the design as his own, but the committee disagreed on that point. Until the time of his death at age 90 in 1999, Sundén was still trying to establish his claim to the credit and the royalties for the design and the matter has never been fully resolved. The Nordic Folkboat
2624-505: The first gasoline-powered outboard offered for sale in significant numbers. It was developed from 1903 in Grosse Ile, Michigan, with a patent application filed in 1905 Starting in 1906, the company went on to make thousands of his "Porto-Motor" units, claiming 25,000 sales by 1914. The inboard boat motor firm of Caille Motor Company of Detroit were instrumental in making the cylinder and engines. The most successful early outboard motor,
Nordic Folkboat - Misplaced Pages Continue
2688-532: The geometry of their design, the wide base of their multiple hulls, for their stability. Designers of performance multihulls, such as the Open 60's , go to great lengths to reduce overall boat weight as much as possible. This leads some to comment that designing a multihull is similar to designing an aircraft. A centreboard or daggerboard is retractable lightweight keel which can be pulled up in shallow water. On small sailboats, masts may be "stepped" (put in place) with
2752-439: The helmsman and others in the water. A safety measure is a " kill cord " attached to the boat and helmsman, which cuts the motor if the helmsman falls overboard. The most common type of cooling used on outboards of all eras use a rubber impeller to pump water from below the waterline up into the engine. This design has remained the standard due mainly to the efficiency and simplicity of its design. One disadvantage to this system
2816-470: The hull itself has sufficient buoyancy to remain afloat. A multihull optimized for light weight (at the expense of cruising amenities and storage for food and other supplies), combined with the absence of ballast can result in performance gains in terms of acceleration, top speed, and manoeuvrability. The lack of ballast makes it much easier to get a lightweight multihull on plane, reducing its wetted surface area and thus its drag. Reduced overall weight means
2880-450: The hulls. All these hull types may also be manufactured as, or outfitted with, hydrofoils . All vessels have a keel , it is the backbone of the hull. In traditional construction, it is the structure upon which all else depends. Modern monocoque designs include a virtual keel. Even multihulls have keels. On a sailboat, the word "keel" is also used to refer to the area that is added to the hull to improve its lateral plane. The lateral plane
2944-637: The late 1920s, such as the Roness and Sharland. In 1962 Homelite introduced a four-stroke outboard a 55-horsepower (41 kW) motor, based on the four-cylinder Crosley automobile engine. This outboard was called the Bearcat and was later purchased by Fischer-Pierce, the makers of Boston Whaler, for use in their boats because of their advantages over two-stroke engines. In 1964, Honda Motor Co. introduced its first four-stroke powerhead. In 1984, Yamaha introduced their first four-stroke outboards, which were only available in
3008-616: The low-power range. In 1990 Honda released 35 hp and 45 hp four-stroke models. They continued to lead in the development of four-stroke engines throughout the 1990s as US and European exhaust emissions regulations such as CARB ( California Air Resources Board ) led to the proliferation of four-stroke outboards. At first, North American manufacturers such as Mercury and OMC used engine technology from Japanese manufacturers such as Yamaha and Suzuki until they were able to develop their own four-stroke engine. The inherent advantages of four-stroke motors included: lower pollution (especially oil in
3072-573: The mainmast, but forward of the rudder post. The second mast is called the mizzen mast and the sail is called the mizzen sail. A ketch can also be Cutter-rigged with two head sails. A schooner has a mainmast taller than its foremast , distinguishing it from a ketch or a yawl. A schooner can have more than two masts, with the foremast always lower than the foremost main. Traditional topsail schooners have topmasts allowing triangular topsails sails to be flown above their gaff sails ; many modern schooners are Bermuda rigged. The most common modern sailboat
3136-477: The manufacturer, newer engines benefit from advanced technology such as multiple valves per cylinder, variable camshaft timing (Honda's VTEC), boosted low end torque (Honda's BLAST), 3-way cooling systems, and closed loop fuel injection. Mercury Verado four-strokes are unique in that they are supercharged . Mercury Marine, Mercury Racing, Tohatsu, Yamaha Marine, Nissan and Evinrude each developed computer-controlled direct-injected two-stroke engines. Each brand boasts
3200-401: The maximum recommended engine powers for the hulls. In the united kingdom, boats have CE plates on the transoms which specify maximum engine power, shaft length, maximum engine weight and maximum number of persons or maximum load. Outboard motor shaft lengths are standardized to fit 15-, 20- and 25-inch (38-, 51- and 64-centimeter) transoms . If the shaft is too long it will extend farther into
3264-464: The motor as well as the propeller . If the electric motor required to move the pistons which raise or lower the engine is malfunctioning, every outboard motor is equipped with a manual piston release which will allow the operator to drop the motor down to its lowest setting. Large ships, boats and yachts will inevitably have inboard engines. Medium size vessels may have either inboards or outboards, and small vessels rarely have inboard motors. If one has
SECTION 50
#17330848809323328-402: The outboard motor to be swiveled by the operator in almost all directions: Sideways for direction, up and down to change the thrust line according to speed or bow lift, elevate completely out of water for easy starting, placing the drive shaft and the propeller forward along the side of the boat for reverse, or put them inside the boat for propeller replacement, which can be a regular occurrence to
3392-462: The power head like a conventional petrol engine . With this setup, a motor can produce 10 kW output or more and is able to replace a petrol engine of 15 HP or more. The advantage of the induction or asynchronous motor is the power transfer to the rotor by means of electromagnetic induction . As these engines do not use permanent magnets , they require less maintenance and develop more torque at lower propeller speeds. Pump-jet propulsion
3456-399: The shape of the keel. A monohull's keel is made effective by a combination of weight, depth, and length. Most modern monohull boats have fin keels, which are heavy and deep, but short in relation to the hull length. More traditional yachts carried a full keel which is generally half or more of the length of the boat. A recent feature is a winged keel , which is short and shallow, but carries
3520-622: The system is pressurized. Lehr is regarded as the first manufacturer to have brought a propane-powered outboard motor to market by Popular Mechanics and other boating publications. The first known outboard motor was a small 11 pound (5 kg) electric unit designed around 1870 by Gustave Trouvé , and patented in May 1880 (Patent N° 136,560). Later about 25 petrol powered outboards may have been produced in 1896 by American Motors Co —but neither of these two pioneering efforts appear to have had much impact. The Waterman outboard engine appears to be
3584-445: The traditional timber folkboat were created by Erik Andreasen and Sven Svendsen. They were molded to the exact dimensions and contours of the traditional clinker hull as well as having the same weight and weight distribution. By 2001, more than 950 glass reinforced plastic (GRP) folkboats had been built. In the mid-2000s it was being built by Folkebådcentralen A/S of Denmark , but that company seems to be no longer in business. Today
3648-575: The water (wind and waves). Many large outboards are equipped with power trim , an electric motor on the mounting bracket, with a switch at the helm that enables the operator to adjust the trim angle on the fly. In this case, the motor should be trimmed fully in to start, and trimmed out (with an eye on the tachometer ) as the boat gains momentum, until it reaches the point just before ventilation begins or further trim adjustment results in an increase in engine speed with no increase in travel speed. Motors not equipped with power trim are manually adjustable using
3712-445: The water than necessary creating drag , which will impair performance and fuel economy. If the shaft is too short, the motor will be prone to ventilation. Even worse, if the water intake ports on the lower unit are not sufficiently submerged, engine overheating is likely, which can result in severe damage. Different outboard engine brands require different transom dimensions and sizes. This affects performance and trim. Motor height on
3776-401: The water), noise reduction, increased fuel economy, and increased torque at low engine speeds. Honda Marine Group , Mercury Marine , Mercury Racing, Nissan Marine, Suzuki Marine, Tohatsu Outboards, Yamaha Marine, and China Oshen-Hyfong marine have all developed new four-stroke engines. Some are carburetted, usually the smaller engines. The balance are electronically fuel-injected. Depending on
3840-399: The waterways. A dinghy is a type of small open sailboat commonly used for recreation, sail training , and tending a larger vessel. They are popular in youth sailing programs for their short LOA , simple operation and minimal maintenance. They have three (or fewer) sails : the mainsail , jib , and spinnaker . Ketches are similar to a sloop, but there is a second shorter mast astern of
3904-720: The weight of the boat, but is generally around 30%. It creates two problems; one, it gives the monohull tremendous inertia, making it less maneuverable and reducing its acceleration. Secondly, unless it has been built with buoyant foam or air tanks, if a monohull fills with water, it will sink. Multihulls rely on the geometry and the broad stance of their multiple hulls for their stability, eschewing any form of ballast. Some multihulls are designed to be as light-weight as possible while still maintaining structural integrity. They can be built with foam-filled flotation chambers and some modern trimarans are rated as unsinkable, meaning that, should every crew compartment be completely filled with water,
SECTION 60
#17330848809323968-419: Was created by Norwegian-American inventor Ole Evinrude in 1909. Historically, a majority of outboards have been two-stroke powerheads fitted with a carburetor due to the design's inherent simplicity, reliability, low cost and light weight. Drawbacks include increased pollution, due to the high volume of unburned gasoline and oil in their exhaust, and louder noise. Four-stroke outboards have been sold since
4032-536: Was never credited as the actual designer of the boat. The Nordic Folkboat was developed into the Sundén-designed International Folkboat in 1967. The International Folkboat was expressly designed for fibreglass construction. The International 25 and the Olsen 26 are also based upon this design. The Junior Folkboat designed by Erik Salander [ sv ] actually dates from 1929. It
4096-432: Was originally called the "Juniors Bad" (Junior boat), but was later renamed because of its strong resemblance to the later and larger Nordic Folkboat. The design has been built by a number of different builders since the first were built in 1942 using wooden clinker construction . By the mid 1970s, timber costs and competition from modern fibreglass boats meant that the folkboat sales were dwindling. Fibreglass versions of
#931068