112-692: The Gibson Firebird is a solid-body electric guitar manufactured by Gibson beginning in 1963. The Gibson Guitar Corporation released several new styles during the 1950s to compete with Fender 's solid-body instruments, such as the Telecaster and Stratocaster . After success with the Les Paul in the 1950s, Gibson's popularity began to wane in the 1960s. Fender's colors, shapes and multiple pickups were endorsed by notable guitarists. Gibson's guitars, most of which were hollow or semi-hollow designs, seemed old-fashioned. Coupled with higher prices, this contributed to
224-466: A monaural signal. Many guitars with active electronics use a jack with an extra contact normally used for stereo . These guitars use the extra contact to break the ground connection to the on-board battery to preserve battery life when the guitar is unplugged. These guitars require a mono plug to close the internal switch and connect the battery to ground. Standard guitar cables use a high-impedance 1 ⁄ 4 inch (6.35 mm) mono plug. These have
336-400: A vibrato embellishment. A plastic pickguard on some guitars protects the body from scratches or covers the control cavity, which holds most of the wiring. The degree to which the choice of woods and other materials in the solid-guitar body (3) affects the sonic character of the amplified signal is disputed. Many believe it is highly significant, while others think the difference between woods
448-525: A United States patent for an Electrical Stringed Musical Instrument and the patent was later issued in 1937. By the time it was patented, other manufacturers were already making their own electric guitar designs. Early electric guitar manufacturers include Rickenbacker in 1932; Dobro in 1933; National, AudioVox and Volu-tone in 1934; Vega , Epiphone (Electrophone and Electar), and Gibson in 1935 and many others by 1936. By early-mid 1935, Electro String Instrument Corporation had achieved success with
560-590: A built-in system to electrically amplify their output without altering their tone as an alternative to using a separate microphone. The system may consist of piezoelectric pickups mounted under the bridge, or a low-mass microphone (usually a condenser mic) inside the body of the guitar that converts the vibrations in the body into electronic signals. Combinations of these types of pickups may be used, with an integral mixer/preamp/graphic equalizer. Such instruments are called electric acoustic guitars . They are regarded as acoustic guitars rather than electric guitars because
672-642: A cheaper range of lower grade instruments still bearing the Epiphone label, but now sourced in Japan. By the late 1970s, Epiphone production began moving to Korea, and by the mid-1980s, all Epiphones were Korean-built. Beginning in 1997, Epiphone moved its production to China and Indonesia. Since merging with Gibson, the brand has been used for a number of different guitars, some manufactured by Gibson itself in its own factories, and some manufactured by other companies such as Matsumoku under contract to Gibson and marketed under
784-433: A commemorative "Bicentennial" model released in 1976 which was made available in a variety of finishes including black, vintage white, natural, and the traditional sunburst. The bicentennial model was also distinguished by gold hardware and a red-white-blue logo on the white pickguard. The logo on most other models is red. The "reissue" Firebirds are usually based on the original reverse body design, though Gibson reintroduced
896-583: A decline in sales. Gibson had made forays into radical body shapes — the Flying V and Explorer in the 1950s — which met limited initial success. The president of Gibson, Ted McCarty , hired car designer Ray Dietrich to design a guitar that would have popular appeal. Under Dietrich, the Firebird took on the lines of mid-50s car tailfins, taking the Explorer design and rounding the edges. The most unusual aspect
1008-576: A folding neck called the "Foldaxe" was designed and built for Chet Atkins by Roger C. Field . Steinberger guitars developed a line of exotic, carbon fiber instruments without headstocks, with tuning done on the bridge instead. Fingerboards vary as much as necks. The fingerboard surface usually has a cross-sectional radius that is optimized to accommodate finger movement for different playing techniques. Fingerboard radius typically ranges from nearly flat (a very large radius) to radically arched (a small radius). The vintage Fender Telecaster , for example, has
1120-789: A full equalizer, gain, volume, reverb, and presence control. As of 2012, Epiphone has ceased production of their line of amplifiers with the exception of the Player and Performance Pack practice amplifiers, available only in Epiphone's starter packages. These Amplifiers were under the Epiphone Electar brand. In 2014 the 1939 Electar Century 18-watt valve amplifier was reissued in an updated 75th anniversary Limited Edition. Epiphone instruments made between 1957 and 1970 were at Gibson facilities on Parsons Street and Eleanor Street in Kalamazoo, Michigan. Solid body guitars with flat tops and backs were made at
1232-428: A guitar amplifier and speaker. When an electric guitar is played, string movement produces a signal by generating (i.e., inducing ) a small electric current in the magnetic pickups, which are magnets wound with coils of very fine wire. The signal passes through the tone and volume circuits to the output jack, and through a cable to an amplifier . The current induced is proportional to such factors as string density and
SECTION 10
#17330848751271344-519: A hard, polymerized finish. Strings vibrating in the magnetic field of the pickups (3.1, 3.2) produce an electric current in the pickup winding that passes through the tone and volume controls (3.8) to the output jack. Some guitars have piezo pickups, in addition to or instead of magnetic pickups. Some guitars have a fixed bridge (3.4). Others have a spring-loaded hinged bridge called a vibrato bar , tremolo bar , or whammy bar , which lets players bend notes or chords up or down in pitch or perform
1456-803: A major component in the development of electric blues , rock and roll , rock music , heavy metal music and many other genres of music. Electric guitar design and construction varies greatly in the shape of the body and the configuration of the neck, bridge, and pickups. Guitars may have a fixed bridge or a spring-loaded hinged bridge , which lets players "bend" the pitch of notes or chords up or down, or perform vibrato effects. The sound of an electric guitar can be modified by new playing techniques such as string bending , tapping , and hammering-on , using audio feedback , or slide guitar playing. There are several types of electric guitar. Early forms were hollow-body semi-acoustic guitars , while solid body guitars developed later. String configurations include
1568-538: A much improved range of flat-top acoustic guitars , incorporating elements of Gibson's own designs. The 1961 catalog shows that the Emperor, Deluxe, Triumph and Zenith were still available as acoustic archtops, the Emperor, Sheraton, Broadway, Zephyr and Century together with new models the Windsor, Casino and Sorrento as electric archtops, the new models Crestwood Custom, Wilshire, Coronet and Olympic as electric solidbodies, while
1680-658: A neck-through design is difficult or even impossible to repair, depending on the damage. Historically, the bolt-on style has been more popular for ease of installation and adjustment. Since bolt-on necks can be easily removed, there is an after-market in replacement bolt-on necks from companies such as Warmoth and Mighty Mite. Some instruments—notably most Gibson models—continue to use set-in glued necks. Neck-through bodies are somewhat more common in bass guitars. Materials for necks are selected for dimensional stability and rigidity, and some allege that they influence tone. Hardwoods are preferred, with maple , mahogany , and ash topping
1792-608: A range of higher quality instruments under the "Elite Series" moniker which were built by Terada and FujiGen in Japan. After legal action by Ovation the name was changed to Elitist in 2003. As of 2008, all of the Elitist models have been discontinued with the exception of the Elitist Casino and the Dwight Trash Casino. The Epiphone Elitist guitars included features such as higher grade woods, bone nuts, hand-rubbed finishes, "Made in
1904-434: A rhythm guitarist and a lead guitarist. Many experiments with electrically amplifying the vibrations of a string instrument were made dating back to the early part of the 20th century. Patents from the 1910s show telephone transmitters were adapted and placed inside violins and banjos to amplify the sound. Hobbyists in the 1920s used carbon button microphones attached to the bridge ; however, these detected vibrations from
2016-423: A semi-acoustic tone (see below) or both. Semi-acoustic guitars have a hollow body similar to an acoustic guitar and electromagnetic pickups mounted directly into the body. They work in a similar way to solid-body electric guitars except that because the hollow body also vibrates, the pickups convert a combination of string and body vibration into an electrical signal. Many models, known as semi-hollow bodies, have
2128-418: A single block of wood, semi-acoustic guitar bodies are made from multiple pieces of wood in an archtop form, a method of construction different from the typical steel string acoustic guitar . The top is formed from a moderately thick piece of wood which is then carved into a thin outward-curving shape, whereas conventional acoustic guitars have a thin, flat top. Some steel-string acoustic guitars include
2240-570: A solid block running through the middle of the soundbox designed to reduce acoustic feedback. They do not provide enough acoustic volume for live performance, but they can be used unplugged for quiet practice. Semi-acoustic guitars are noted for being able to provide a sweet, plaintive, or funky tone. They are used in many genres, including jazz, blues, funk , sixties pop, and indie rock . They generally have cello-style F-shaped sound holes , which can be blocked off to further reduce feedback. Whereas chambered guitars are made, like solid-body guitars, from
2352-436: A standard acoustic guitar . It uses one or more pickups to convert the vibration of its strings into electrical signals , which ultimately are reproduced as sound by loudspeakers . The sound is sometimes shaped or electronically altered to achieve different timbres or tonal qualities via amplifier settings or knobs on the guitar. Often, this is done through the use of effects such as reverb , distortion and "overdrive" ;
SECTION 20
#17330848751272464-514: A standard glued-in ("set") neck rather than neck-through construction, as well as other, less noticeable changes in design and build. Pickup and tailpiece configuration for the V and VII were the same as the earlier "reverse" models, although the I- and III-models were now shipped with two or three P-90 pickups and plain vibratos. After a few years of disappointing sales, the "non-reverse" line was dropped. "Reverse" body Firebirds were first reissued in 1972, with
2576-399: A tip and sleeve configuration referred to as a TS phone connector . The voltage is usually around 1 to 9 millivolts . A few guitars, such as Rickenbacker guitars equipped with Rick-O-Sound , feature stereo output. There are a variety of ways the "stereo" effect may be implemented. Commonly, but not exclusively, stereo guitars route the neck and bridge pickups to separate output buses on
2688-405: A top so heavily reinforced that it essentially functioned as a solid-body instrument. Unlike acoustic guitars, solid-body electric guitars have no vibrating soundboard to amplify string vibration. Instead, solid-body instruments depend on electric pickups, and an amplifier ("amp") and speaker . The solid body ensures that the amplified sound reproduces the string vibration alone, thus avoiding
2800-667: A triple single-coil guitar. The history of electric guitars has been summarized by Guitar World magazine, and the earliest electric guitar on their top 10 list is the Ro-Pat-In Electro A-25 "Frying Pan" (1932) described as "The first-fully functioning solid-body electric guitar to be manufactured and sold". It was the first electric guitar used in a publicly promoted performance, performed by Gage Brewer in Wichita, Kansas in October 1932. The most recent electric guitar on this list
2912-539: A tube design, and some had reverb and tremolo. Gibson decided to launch a new line of Epiphone tube amplifiers in 2005 with models including the So Cal, Blues Custom, Epiphone Valve Junior and the solid state Triggerman range. The Valve Hot Rod and Valve Senior followed in 2009. The Valve Hot Rod is a 5 watt amp like the Valve Junior, but has a gain and reverb control. The Valve Senior offers 20 watts of power, with
3024-590: A typical small radius of approximately 7.25 inches (18.4 cm). Some manufacturers have experimented with fret profile and material, fret layout, number of frets, and modifications of the fingerboard surface for various reasons. Some innovations were intended to improve playability by ergonomic means, such as Warmoth Guitars' compound radius fingerboard. Scalloped fingerboards added enhanced microtonality during fast legato runs. Fanned frets intend to provide each string with an optimal playing tension and enhanced musicality. Some guitars have no frets , while others, like
3136-409: A way to reduce or counter the sound, as they are designed to "buck" (in the verb sense of oppose or resist ) the hum, hence their name. The high combined inductance of the two coils also leads to the richer, "fatter" tone associated with humbucking pickups. Electric guitar necks vary in composition and shape. The primary metric of guitar necks is the scale length , which is the vibrating length of
3248-409: A wood post with a neck attached and two hollow-body halves attached to the sides for appearance only — shares nothing in common for design or hardware with the solid-body Gibson Les Paul , designed by Ted McCarty and introduced in 1952. The feedback associated with amplified hollow-bodied electric guitars was understood long before Paul's "log" was created in 1940; Gage Brewer's Ro-Pat-In of 1932 had
3360-545: Is made of solid wood, without functionally resonating air spaces. The first solid-body Spanish standard guitar was offered by Vivi-Tone no later than 1934. This model featured a guitar-shaped body of a single sheet of plywood affixed to a wood frame. Another early, substantially solid Spanish electric guitar, called the Electro Spanish, was marketed by the Rickenbacker guitar company in 1935 and made of Bakelite . By 1936,
3472-406: Is often used in two roles: as a rhythm guitar , which plays the chord sequences or progressions , and riffs , and sets the beat (as part of a rhythm section ); and as a lead guitar , which provides instrumental melody lines, melodic instrumental fill passages, and solos . In a small group, such as a power trio , one guitarist may switch between both roles; in larger groups there is often
Gibson Firebird - Misplaced Pages Continue
3584-473: Is simple carpenters' wood glue, and were finished in hard, quick-to-apply polyester resin rather than the traditional nitro-cellulose lacquer used by Gibson Epiphone guitars assembled or made in the US use lacquer finishes unless it's a san lacquer (SL for short), but those made outside of the US use a polyurethane finish because of pollution requirements. Those particular budget considerations, along with others such as
3696-418: Is subtle. In acoustic and archtop guitars, wood choices more clearly affect tone. Woods typically used in solid-body electric guitars include alder (brighter, but well rounded), swamp ash (similar to alder, but with more pronounced highs and lows), mahogany (dark, bassy, warm), poplar (similar to alder), and basswood (very neutral). Maple , a very bright tonewood , is also a popular body wood but
3808-481: Is that the guitar is "backward" in that the right-hand (treble) horn of the body is longer than the other. Thus, the original Firebirds were unofficially referred to as "reverse". The Firebird is the first Gibson solid-body to use neck-through construction, wherein the neck extended to the tail end of the body. The neck itself is made up of five plies of mahogany interspersed with four narrow strips of walnut for added strength. Other features were reverse headstock (with
3920-450: Is very heavy. For this reason, it is often placed as a "cap" on a guitar made primarily of another wood. Cheaper guitars are often made of cheaper woods, such as plywood , pine , or agathis —not true hardwoods—which can affect durability and tone. Though most guitars are made of wood, any material may be used. Materials such as plastic, metal, and even cardboard have been used in some instruments. The guitar output jack typically provides
4032-771: The Epiphone Les Paul , which serves as a budget model comparable to the Gibson Les Paul . Secondly, Epiphone has also been used to brand models under alternate names, but are otherwise similar to more expensive Gibson-branded guitars, for example the Epiphone G-400 is functionally equivalent to the Gibson SG , and the Epiphone Dot is essentially a budget version of the Gibson ES-335 . Thirdly are models which are exclusive to
4144-687: The Epiphone Sheraton (co-developed with the Gibson ES-335 & sharing its semi-hollow body, but with, Epiphone's pre-Gibson "Frequensator" tailpiece and "New York" mini-humbucker pickups, and significantly fancier inlays) and Sheraton II (replacing the Frequensator with Gibson's "stop-bar" tailpiece), the Epiphone Casino (similar to the Gibson ES-330 ), the Epiphone Caballero (similar to
4256-597: The Genesis solid body guitar. By 1980, most Japanese-only designs were available for worldwide distribution. One in particular, the ES930J, was made at the famed Terada factory and was a superior instrument. The Matsumoku-made archtops, such as the Emperor, Riviera, Sheraton and Casino, were available into the mid-1980s. From the 1980s, Epiphones were manufactured mainly in South Korea and Japan by contractors licensed by Gibson. One of
4368-670: The Gibson SG used by Angus Young from the group AC/DC . Some otherwise solid-bodied guitars, such as the Gibson Les Paul Supreme, the PRS Singlecut, and the Fender Telecaster Thinline , are built with hollow chambers in the body. These chambers are designed to not interfere with the critical bridge and string anchor point on the solid body. In the case of Gibson and PRS, these are called chambered bodies . The motivation for this may be to reduce weight, to achieve
4480-471: The Gittler guitar , have no neck in the traditional sense. Epiphone Epiphone ( / ˌ ɛ . p ə . f oʊ n / ) is an American musical instrument brand that traces its roots to a musical instrument manufacturing business founded in 1873 by Anastasios Stathopoulos in İzmir , Ottoman Empire , and moved to New York City in 1908. After taking over his father's business, Epaminondas Stathopoulos named
4592-649: The Slingerland company introduced a wooden solid-body electric model, the Slingerland Songster 401 (and a lap steel counterpart, the Songster 400). Gibson's first production electric guitar, marketed in 1936, was the ES-150 model ("ES" for "Electric Spanish", and "150" reflecting the $ 150 price of the instrument, along with matching amplifier). The ES-150 guitar featured a single-coil, hexagonally shaped "bar" pickup, which
Gibson Firebird - Misplaced Pages Continue
4704-527: The oud and the laouto ). Stathopoulos moved to the United States in 1903 and continued to make his original instruments, as well as mandolins , from a factory at 35-37 36th Street in Long Island City , Queens , New York . Anastasios died in 1915, and his son, Epaminondas ("Epi"), took over. After two years, the company became known as "The House of Stathopoulo". Just after the end of World War I ,
4816-409: The six-string guitar (the most common type), which is usually tuned E, A, D, G, B, E, from lowest to highest strings; the seven-string guitar , which typically adds a low B string below the low E; the eight-string guitar , which typically adds a low E or F# string below the low B; and the twelve-string guitar , which has six two-string courses similar to a mandolin . In rock, the electric guitar
4928-418: The wolf tones and unwanted feedback associated with amplified acoustic guitars. These guitars are generally made of hardwood covered with a hard polymer finish, often polyester or lacquer. In large production facilities, the wood is stored for three to six months in a wood-drying kiln before being cut to shape. Premium custom-built guitars are frequently made with much older , hand-selected wood. One of
5040-569: The "Frying Pan", and set out to capture a new audience through its release of the Electro-Spanish Model B and the Electro-Spanish Ken Roberts , which was the first full 25-inch scale electric guitar ever produced. The Electro-Spanish Ken Roberts was revolutionary for its time, providing players a full 25-inch scale, with easy access to 17 frets free of the body. Unlike other lap-steel electrified instruments produced during
5152-524: The (top of the line) Emperor model with added cutaway and pickups. Other archtops appeared solely in the amplified form, being the Zephyr, Century and Coronet (all 1939), Kent (1950) and a signature model named for Harry Volpe (1955). Accompanying the archtop line were a range of flat top instruments, although these never acquired the cachet of their archtop companions. These included 2 Hawaiian models (the Madrid and
5264-433: The 1970s onwards, production of Epiphone guitars has largely taken place in Japan, Korea and China (refer section "Manufacturing", below), with a very small number of models also produced in the U.S.A. Since the 2000s, Epiphone branded guitars have fallen broadly into three categories. Firstly, Epiphone is used as a "budget brand" for Gibson, producing identically-named but lower-priced versions of popular Gibson models, such as
5376-436: The A, featured a flat top and back, the B had an arched back and a flat top, while the remainder had arched tops and backs; additionally, they appear to have been available in two different sizes. These guitars had a distinctive sound but were not very successful commercially, and are rarely seen today. Commencing around 1931, Epiphone decided to release a new range of full body archtop guitars in direct competition with Gibson,
5488-589: The Broadcaster. Another notable solid-body design is the Fender Stratocaster , which was introduced in 1954 and became extremely popular among musicians in the 1960s and 1970s for its wide tonal capabilities and more comfortable ergonomics than other models. Different styles of guitar have different pick-up styles, the main being 2 or 3 " single-coil " pick-ups or a double humbucker , with the Stratocaster being
5600-511: The Eleanor Street plants (both Gibson and Epiphone). Some of these Epiphone instruments were effectively identical to the relevant Gibson versions, perhaps made with same timber, materials and components as the contemporary equivalent Gibson guitars. Epiphone also continued its production of archtop guitars using the same patterns and molds from Epi's New York era. Some specific examples of Gibson-era Epiphone instruments from this period includes
5712-515: The Epiphone brand without equivalent models produced under the Gibson brand, such as the Epiphone Coronet . As of January 2021, Epiphone was marketing guitars under several lines, including several categorized on their website as "inspired by Gibson" for models that serve as the budget Gibson version. Historically, hundreds of different models have borne the Epiphone brand, and many are available in
SECTION 50
#17330848751275824-430: The Epiphone brand. Epiphone's first foray into the guitar market came in around 1928, with the release of the "Recording" range, styled models A through E. These guitars featured an unusual asymmetric body shape with what was in effect a strongly sloping cutaway on the upper treble bout, and either a trapeze tailpiece or a pin bridge, together with pegheads and tuners reminiscent of the company's banjos. The cheapest model,
5936-427: The Epiphone range. The marketing strategy used was that since the number of Gibson dealerships was limited by design, equivalent quality instruments under the Epiphone label could be offered for sale through other dealerships thus in principle increasing market share overall. This arrangement lasted until 1969 at which point Gibson decided to cease production of the high grade, U.S.A.-made Epiphone instruments in favour of
6048-562: The FT (Flat Top) guitars. Construction of these guitars differed greatly from past Epiphone models. For the first several years of production in Japan, Epiphone guitars were actually rebranded designs already produced by the Matsumoku Company. By 1975, the Japanese market started seeing some of the more familiar designs and names being reintroduced. These guitars were of higher quality than that of
6160-1103: The Gibson LG-0), the Epiphone Cortez (similar to the Gibson LG-2), the Epiphone Frontier (similar to the Gibson Hummingbird), the Epiphone Olympic Special (similar to the Gibson Melody Maker ), the Epiphone Sorrento (similar to the Gibson ES-125 TC, except for a few cosmetic changes), and the Epiphone Texan (similar to the Gibson J-45 , apart from a change in scale-length). The other Kalamazoo-made Epiphones had technical or cosmetic relationship with
6272-796: The Gibson line, some unique to the Epiphone line—generally considered equal in construction quality to those produced under the Gibson brand. From 1970 onwards, Gibson ceased production of Epiphones in its U.S.A factory and moved production offshore for a range of cheaper models. Today, Epiphone is still used as a brand for the Gibson company, both for budget models of other Gibson-branded products and for several Epiphone-exclusive models. Aside from guitars, Epiphone has also made double basses , banjos , and other string instruments , as well as amplifiers . Epiphone began in 1873, in Smyrna , Ottoman Empire (now İzmir , Turkey ), where Greek founder Anastasios Stathopoulos made his own fiddles and lutes (specifically,
6384-454: The Gibson line/s of the day. In England in the 1960s, several Epiphone models were brought to particular prominence via their use by The Beatles , Paul McCartney favouring a 1964 Epiphone Texan that he purchased in 1965 and used for the writing of " Yesterday " among other songs, while John Lennon , Paul McCartney and George Harrison all performed using Epiphone Casinos through much of the group's years of early commercial success. From
6496-838: The Gibson range of the day—for example the Riviera and Casino were very similar to the Gibson ES-335 and ES-330, respectively, the Frontier was somewhat similar to the Gibson Dove, while the Texan, Cortez and Cabellero were generally equivalent to the Gibson J-45, LG-2 and LG-0, respectively—others had no equivalent in the Gibson range, the Sheraton (semi-acoustic thinline version) and Excellente (acoustic) being top-of-the line instruments without any real parallel in
6608-455: The Gibson-owned era for the company. In 1957 Epiphone, Inc. was purchased by Gibson , its main rival in the archtop guitar market at the time. Gibson relocated Epiphone's manufacturing operation from its original Queens, New York , factory to Gibson's Kalamazoo, Michigan , factory, where production of both ranges took place until 1969, with Epiphone instruments—some with "sister" models in
6720-504: The Les Paul and SG line, which used the terms "Junior", "Special", "Standard" and "Custom", the Firebird used the Roman numerals "I", "III", "V" and "VII". Gibson's line of Thunderbird basses is rooted in the design of the Firebird, and uses even Roman numerals ("II" and "IV") to distinguish it. From 1965 to 1969, Gibson introduced "non-reverse" models after failing to achieve marketing success with
6832-569: The Melody, later the Zenith Tenor), Olympic, and Beverly. Other models introduced a little later comprised the Emperor (1936), Byron (1938), Ritz (1941) and Devon (1951). These instruments were initially offered in acoustic, non-cutaway form, with cutaways appearing (often with the additional designation "Regent") from the late 1940s onwards, and with the addition of pickups, by the added designation of "Zephyr", thus an "Zephyr Emperor Regent" would indicate
SECTION 60
#17330848751276944-641: The Navarre), plus the flat top FT 75 (introduced by 1935, discontinued 1942), FT 37 (1935-1942), FT 27 (1935-1941), FT De Luxe (1939-1942), FT 110, FT 79 and FT 45 (all 1942, all continued into Gibson era), FT 50 (1941-1950) and FT 30 (1941-1954, then reactivated in the Gibson era). Several cutaway flat top instruments were also made, designated the De Luxe Cutaway (also as the FT 210) and the Zephyr Cutaway. It seems that Epiphone used ladder- rather than X-bracing for
7056-515: The acoustic range comprised the Seville (a nylon string instrument), and the steel string Frontier (continuation of FT 110), Texan (continuation of FT 79), Cortez (continuation of FT 45) and Caballero (continuation of FT 30). Subsequent additions to these lines included the semi-acoustic Granada, Professional and Riviera models (all introduced 1962); as well as artist-endorsed models for Al Caiola (the "Caiola", introduced 1963) and Howard Roberts (1964),
7168-449: The amount of movement over the pickups. Because of their natural qualities, magnetic pickups tend to pick up ambient, usually unwanted electromagnetic interference or EMI. This mains hum results in a tone of 50 or 60 cycles per second depending on the powerline frequency of the local alternating current supply. The resulting hum is particularly strong with single-coil pickups. Double-coil or " humbucker " pickups were invented as
7280-616: The back of the guitar by metal ferrules . Many believe this design improves a guitar's sustain and timbre . A few examples of string-through body guitars are the Fender Telecaster Thinline , the Fender Telecaster Deluxe , the B.C. Rich IT Warlock and Mockingbird, and the Schecter Omen 6 and 7 series. Compared to an acoustic guitar, which has a hollow body, electric guitars make much less audible sound when their strings are plucked, so electric guitars are normally plugged into
7392-418: The body at the base of the guitar. These appear on Rickenbackers , Gretsches , Epiphones , a wide variety of archtop guitars , particularly jazz guitars , and the 1952 Gibson Les Paul. Pictured is a tremolo arm or vibrato tailpiece - style bridge and tailpiece system, often called a whammy bar or trem . It uses a lever ("vibrato arm") attached to the bridge that can temporarily slacken or tighten
7504-430: The body. Set-in necks are glued to the body at the factory. This is the traditional type of joint. Leo Fender pioneered bolt-on necks on electric guitars to facilitate easy adjustment and replacement. Neck-through instruments extend the neck to the length of the instrument so that it forms the center of the body. While a set-in neck can be carefully unglued by a skilled luthier , and a bolt-on neck can simply be unscrewed,
7616-555: The bridge on top of the instrument, resulting in a weak signal. Electric guitars were originally designed by acoustic guitar makers and instrument manufacturers. The demand for amplified guitars began during the big band era; as orchestras increased in size, guitar players soon realized the necessity in guitar amplification and electrification. The first electric guitars used in jazz were hollow archtop acoustic guitar bodies with electromagnetic transducers . The first electrically amplified stringed instrument to be marketed commercially
7728-546: The closer the fret spacing. Opinions vary regarding the effect of scale length on tone and feel. Popular opinion holds that longer scale length contributes to greater amplitude . Reports of playing feel are greatly complicated by the many factors involved in this perception. String gauge and design, neck construction and relief, guitar setup, playing style, and other factors contribute to the subjective impression of playability or feel. Necks are described as bolt-on , set-in , or neck-through , depending on how they attach to
7840-508: The company "Epiphone" as a combination of his own nickname "Epi" and the suffix " -phone " (from Greek phon- , "voice") in 1928, the same year it began making guitars. From the 1930s through to the early 1950s, Epiphone produced a range of both acoustic and (later) electrified archtop guitars that rivalled those produced by Gibson and were the instruments of choice of many professionals; a smaller range of flat-top guitars were also produced, some designations of which were later continued during
7952-417: The company started to make banjos . The company produced its recording line of banjos in 1924 and, four years later, took on the name of the "Epiphone Banjo Company". It produced its first guitars (the "Epiphone Recording" models) in 1928. In 1931 the company commenced production of its "Masterbilt" range of archtop guitars which became very popular and competed successfully with the equivalent range produced at
8064-440: The contractors was Samick , which also built instruments under license for other brands, and in its own name. The brand was primarily used to issue less expensive versions of classic Gibson models. The guitars were constructed using different woods, generally only distantly related to true mahogany , and were fastened with epoxies rather than traditional wood glues. Gibson and Epiphone guitars all use Titebond resin glue, which
8176-399: The different parts of an electric guitar. The headstock (1) contains the metal machine heads (1.1), which use a worm gear for tuning. The nut (1.4)—a thin fret-like strip of metal, plastic, graphite, or bone—supports the strings at the headstock end of the instrument. The frets (2.3) are thin metal strips that stop the string at the correct pitch when the player pushes a string against
8288-538: The effects of different woods or materials on the electric guitar sound. Several neck shapes appear on guitars, including shapes known as C necks, U necks, and V necks. These refer to the cross-sectional shape of the neck (especially near the nut). Several sizes of fret wire are available, with traditional players often preferring thin frets, and metal shredders liking thick frets. Thin frets are considered better for playing chords, while thick frets allow lead guitarists to bend notes with less effort. An electric guitar with
8400-462: The electric guitar on record include Les Paul , Eddie Durham , George Barnes , Lonnie Johnson , Sister Rosetta Tharpe , T-Bone Walker , and Charlie Christian . During the 1950s and 1960s, the electric guitar became the most important instrument in popular music . It has evolved into an instrument that is capable of a multitude of sounds and styles in genres ranging from pop and rock to folk to country music , blues and jazz . It served as
8512-420: The fingerboard. The truss rod (1.2) is a metal rod (usually adjustable) that counters the tension of the strings to keep the neck straight. Position markers (2.2) provide the player with a reference to the playing position on the fingerboard. The neck and fretboard (2.1) extend from the body. At the neck joint (2.4), the neck is either glued or bolted to the body. The body (3) is typically made of wood with
8624-432: The first improvements on the vibrato system in many years when, in the late 1970s, he experimented with "locking" nuts and bridges that prevent the guitar from losing tuning, even under heavy vibrato bar use. The fourth type of system employs string-through body anchoring. The strings pass over the bridge saddles, then through holes through the top of the guitar body to the back. The strings are typically anchored in place at
8736-432: The first solid-body guitars was invented by Les Paul . Gibson did not present their Gibson Les Paul guitar prototypes to the public, as they did not believe the solid-body style would catch on. Another early solid-body Spanish style guitar, resembling what would become Gibson's Les Paul guitar a decade later, was developed in 1941 by O.W. Appleton, of Nogales, Arizona. Appleton made contact with both Gibson and Fender but
8848-859: The guitar. A stereo cable then routes each pickup to its signal chain or amplifier. For these applications, the most popular connector is a high-impedance 1 ⁄ 4 inch (6.35 mm) plug with a tip, ring, and sleeve configuration, also known as a TRS phone connector . Some studio instruments, notably certain Gibson Les Paul models, incorporate a low- impedance three-pin XLR connector for balanced audio . Many exotic arrangements and connectors exist that support features such as midi and hexaphonic pickups. The bridge and tailpiece , while serving separate purposes, work closely together to affect playing style and tone. There are four basic types of bridge and tailpiece systems on electric guitars. Within these four types are many variants. A hard-tail guitar bridge anchors
8960-763: The guitars made at the Peerless plant, including the vastly underrated Sorrento model, are very well made and are well worth a search. There is a controversial Epiphone guitar using "LU" serial number. It is said those guitars were made in Indonesia under license from Unsung Korea. Between the Peerless period and the opening of the Qingdao plant, many Epiphones were constructed at the Zaozhuang Saehan plant in China. Guitars from his period are considered to be of high quality and, because of
9072-450: The latter is considered to be a key element of electric blues guitar music and jazz , rock and heavy metal guitar playing. Designs also exist combining attributes of electric and acoustic guitars: the semi-acoustic and acoustic-electric guitars. Invented in 1932 by Johannes Isaac, the electric guitar was adopted by jazz guitar players, who wanted to play single-note guitar solos in large big band ensembles. Early proponents of
9184-640: The latter with an unusual oval shaped soundhole. The Riviera was also available in a 12-string version (1965 onwards). New acoustic instruments comprised the Excellente, El Dorado, Troubador and Folkster, along with new "folk oriented" 12-strings the Bard (1962) and Serenader (1963); additions to the classical line comprised the Espana and Madrid (both 1962) and the Barcelona and Classic (both 1963). None of these instruments survived
9296-821: The leading factory manufacturer of archtop guitars of the day. The newly announced "Masterbilt" series comprised the Deluxe (with its tenor version named the Empire), Broadway (tenor version the Bretton, later named the Broadway Tenor), Triumph (tenor version the Hollywood, later the Triumph Tenor), Royal, Spartan (tenor version the Regent, later the Spartan Tenor), Blackstone, Zenith (tenor version
9408-649: The list. The neck and fingerboard can be made from different materials; for example, a guitar may have a maple neck with a rosewood or ebony fingerboard. Today there are expensive and budget guitars exploring other options for fretboard wood for instance Pau-Ferro , both for availability and cheap price while still maintaining quality. In the 1970s, designers began to use exotic human-made materials such as aircraft-grade aluminum , carbon fiber , and ebonol . Makers known for these unusual materials include John Veleno , Travis Bean , Geoff Gould , and Alembic . Aside from possible engineering advantages, some feel that with
9520-422: The non-reverse Firebird in 2002 as a Custom Shop guitar. Epiphone , owned by Gibson, has also issued several models. Beginning in 2010, Gibson stated that they would no longer be creating banjo tuners for the Firebird. Gibson reissues of the Firebird do not use the same pickup build that was originally introduced in 1963. The modern Firebird pickups have a higher output volume, more midrange, and less treble than
9632-438: The nucleus of the new Guild Guitar Company , whose early archtop guitar designs owed a lot to Epiphone. In 1957 the company was acquired by Gibson parent company CMI , who merged Epiphone operations with Gibson. Between 1957 and 1969, the Gibson-owned production of Epiphone instruments took a parallel path to those marketed under the Gibson brand, with many equivalents between the two lines but also some instruments unique to
9744-468: The original design. In July 2019, A former Gibson employee released a video purporting to show the destruction of several hundred Firebird X guitars by driving a tracked excavator over them. The video was met with incredulity and speculation about the true reason for the destruction. Electric guitar An electric guitar is a guitar that requires external electric sound amplification in order to be heard at typical performance volumes, unlike
9856-423: The pickups do not produce a signal directly from the vibration of the strings, but rather from the vibration of the guitar top or body, and the amplification of the sound merely increases volume, not alters tone. Electric guitar design and construction vary greatly in the shape of the body and the configuration of the neck, bridge, and pickups. However, some features are present on most guitars. The photo below shows
9968-585: The previous years of production in Japan and included models such as the Wilshire, Emperor, Riviera and Newport bass. These models were available to the Japanese market only. By 1976 new designs of higher quality were being introduced for export but did not include the current Japanese market models. Notable new designs from this era were the Monticello (Scroll Guitar), the Presentation (PR) and Nova series flat tops and
10080-450: The relative rareness and quality factors, are sought after by Epiphone fans and collectors. In 2004, Gibson opened a factory in Qingdao , China, which manufactures Epiphone guitars. With few exceptions, Epiphones are now built only in the Qingdao factory. Also in 2004, Epiphone introduced a series of acoustic guitars named Masterbilt, after a line of guitars of the 1930s, which are built in
10192-592: The rising cost of rare tonewoods , human-made materials may be economically preferable and more ecologically sensitive. However, wood remains popular in production instruments, though sometimes in conjunction with new materials. Vigier guitars , for example, use a wooden neck reinforced by embedding a light, carbon fiber rod in place of the usual heavier steel bar or adjustable steel truss rod. After-market necks made entirely from carbon fiber fit existing bolt-on instruments. Few, if any, extensive formal investigations have been widely published that confirm or refute claims over
10304-556: The same factory. During the early 1990s, Epiphone released a series called the Imperial Series. These were remakes of the classic Epiphone archtops of the 1930s and '40s. Each instrument was handmade in the FujiGen factory in Japan. This short-lived series was discontinued in 1993, after only 42 Emperors were made. Several other models, including De Luxe, Broadway and Triumph models, were also produced in varying quantities. Production
10416-592: The similar Gibson version. Several Epiphone guitars have been produced in the United States after 1971. The Epiphone Spirit and Special were produced in the early 1980s in Kalamazoo. In 1993, three historic Epiphone acoustic guitars, the Texan, Frontier, and Excellente, were produced by Gibson Acoustic in Montana. The Paul McCartney Texan was produced in 2005, and in 2009, the Epiphone Historic Collection
10528-660: The six iron slug poles of one bobbin, and six iron screw poles of the other bobbin). Original Firebird pickups were also built without any specific bobbin fasteners — their bobbins (and possible "reflector" plate under the bobbins) were held onto the frame during both the wax potting process (to reduce/eliminate feedback and unwanted noise) and the solid metal cover that was soldered to the frame base. There are no screw poles on Firebird pickups. Some Firebirds from 1965 featured Gibson's single-coil P-90 pickup. The Firebird line went on sale in mid-1963 with four models distinguished by pickup and tailpiece configurations (see below). Unlike
10640-522: The strings at or directly behind the bridge and is fastened securely to the top of the instrument. These are common on carved-top guitars, such as the Gibson Les Paul and the Paul Reed Smith models , and on slab-body guitars, such as the Music Man Albert Lee and Fender guitars that are not equipped with a vibrato arm. A floating or trapeze tailpiece (similar to a violin 's) fastens to
10752-405: The strings from nut to bridge. A typical Fender guitar uses a 25.5-inch (65 cm) scale length, while Gibson uses a 24.75-inch (62.9 cm) scale length in their Les Paul . While the scale length of the Les Paul is often described as 24.75 inches, it has varied through the years by as much as a half inch. Frets are positioned proportionally to scale length—the shorter the scale length,
10864-658: The strings to alter the pitch . A player can use this to create a vibrato or a portamento effect. Early vibrato systems were often unreliable and made the guitar go out of tune easily. They also had a limited pitch range. Later Fender designs were better, but Fender held the patent on these, so other companies used older designs for many years. With the expiration of the Fender patent on the Stratocaster -style vibrato, various improvements on this type of internal, multi-spring vibrato system are now available. Floyd Rose introduced one of
10976-424: The termination of manufacturing of Epiphone instruments in Gibson's Kalamazoo plant in 1969, at least in their original form (subsequent Japanese models, some even re-using Kalamazoo-era model names, were of generally cheaper construction, for example using laminated woods and bolt-on necks as compared with their U.S.-made predecessors). While some of the 1960s, U.S.A. built Epiphones had near-equivalents to models in
11088-498: The time by Gibson, its main rival in the archtop market. After Epi died in 1943, control of the company went to his brothers, Orphie and Frixo. In 1951, a four-month-long strike caused a relocation of Epiphone Headquarters from New York City to Philadelphia . A number of Epiphone employees decided to remain in New York rather than relocate to Philadelphia, and spearheaded by George Mann, former Epiphone Vice President and Secretary, formed
11200-581: The time, the Electro-Spanish Ken Roberts was designed to play while standing upright with the guitar on a strap, as with acoustic guitars. The Electro-Spanish Ken Roberts was also the first instrument to feature a hand-operated vibrato as a standard arrangement, a device called the "Vibrola", invented by Doc Kauffman . It is estimated that fewer than 50 Electro-Spanish Ken Roberts were constructed between 1933 and 1937; fewer than 10 are known to survive today. The solid-body electric guitar
11312-448: The tops of their flat top models, which may account for their less success in the market than comparable instruments by the Martin and Gibson guitar companies. Following Epiphone's purchase by Gibson in 1957, the lines of both electric and acoustic guitars were considerably revamped, with the introduction of new thinline hollow-body ( semi-acoustic ) guitars, solidbody electric guitars , and
11424-436: The tuners on the treble side) and "banjo"-style planetary geared tuning keys . The special original Gibson Firebird humbucking pickup (s) — single, dual or triple — were smaller footprint versions of standard Gibson humbucking pickups, but were unique in that inside each of their smaller bobbins contained an alnico bar magnet (standard humbucking pickups and mini-humbucking pickups have one bar magnet that activates
11536-413: The unusual reverse-body design. Gibson had also received complaints from Fender that the Firebird headstock mirrored the Stratocaster and that the body violated Fender's design patents, with Fender threatening a lawsuit. The "non-reverse" body is a more standard double-cutaway design, with the bass horn being longer than the treble horn and the headstock having the tuners mounted on the bass side. It also had
11648-515: The use of plastic nuts, and cheaper hardware and pickups, make for a more affordable instrument. After 1996, Epiphones were built by the Peerless Guitars Co. Ltd., established in 1970 in Busan, South Korea. Many of these Peerless guitars, particularly the 1998 models commemorating their 125th Anniversary, were very well made, represent excellent value, and have become quite collectable. However, all
11760-534: The used guitar market. Epiphone began producing amplifiers in 1935 with the Electar Hawaiian Lap Steel Guitar Outfit. This outfit was an amplifier, case and lap steel guitar stand all rolled into one unit and was supplied by a suitcase manufacturer of the time. Electar Century and Zephyr amplifier models followed. Gibson produced Epiphone amplifiers in the 1960s. These were copies or variations of Gibson and Fender amplifiers . They used
11872-660: The vibrations of the guitar strings into electrical signals, which could then be amplified. Commercial production began in late summer of 1932 by the Ro-Pat-In Corporation (Elect ro - Pat ent- In strument Company), in Los Angeles, a partnership of Beauchamp, Adolph Rickenbacker (originally Rickenbacher), and Paul Barth. In 1934, the company was renamed the Rickenbacker Electro Stringed Instrument Company. In that year Beauchamp applied for
11984-489: Was a cast aluminium lap steel guitar nicknamed the "Frying Pan" designed in 1931 by George Beauchamp , the general manager of the National Stringed Instrument Corporation , with Paul Barth, who was vice president. George Beauchamp, along with Adolph Rickenbacker , invented the electromagnetic pickups. Coils that were wrapped around a magnet would create an electromagnetic field that converted
12096-771: Was created, beginning with the 1962 Wilshire, built by Gibson Custom. Several other models, such as the Sheraton and John Lennon Casinos, were built in Japan and assembled and finished by Gibson USA. In the early 1970s, Matsumoku began to manufacture Epiphone instruments in Japan with the production and distribution being managed by Aria , in cooperation with Gibson. At this time, Epiphone ceased production of all of its traditional designs and began manufacturing markedly less expensive guitars, many of which had less traditional bolt-on style necks and unspecified wood types. Some of these guitars had similar body shapes to traditional Epiphone and Gibson designs but had different names while other models retained certain model designations, such as
12208-475: Was designed by Walt Fuller. It became known as the " Charlie Christian " pickup (named for the jazz guitarist who was among the first to perform with the ES-150 guitar). The ES-150 achieved some popularity but suffered from unequal loudness across the six strings. A functioning solid-body electric guitar was designed and built in 1940 by Les Paul from an Epiphone acoustic archtop as an experiment. His " log guitar " —
12320-640: Was moved back to Nashville and Bozeman for a similar limited run of instruments (250 each of Sheratons, Rivieras, Frontiers, Excellentes and Texans). These guitars were the "Nashville USA Collection" (archtops) and the "Anniversary Series" (acoustics). Contrary to popular information, this line was related to, but not part of the 1994 Gibson Centennial Series commemorating 100 years of the Gibson Guitar Corporation. The Nashville and Anniversary Collections were intended as reintroductions of original, USA built Epiphone models. In 2002, Epiphone began producing
12432-737: Was the Ibanez Jem (1987) which featured "24 frets", an impossibly thin neck" and was "designed to be the ultimate shredder machine". Numerous other important electric guitars are on the list, including Gibson ES-150 (1936), Fender Telecaster (1951), Gibson Les Paul (1952), Gretsch 6128 Duo Jet (1953), Fender Stratocaster (1954), Rickenbacker 360/12 (1964), Van Halen Frankenstrat (1975), Paul Reed Smith Custom (1985) many of these guitars were "successors" to earlier designs. Electric guitar designs eventually became culturally important and visually iconic, with various model companies selling miniature model versions of particularly famous electric guitars, for example,
12544-545: Was unable to sell the idea behind his "App" guitar to either company. In 1946, Merle Travis commissioned steel guitar builder Paul Bigsby to build him a solid-body Spanish-style electric. Bigsby delivered the guitar in 1948. The first mass-produced solid-body guitar was Fender Esquire and Fender Broadcaster (later to become the Fender Telecaster ), first made in 1950, five years after Les Paul made his prototype . The Gibson Les Paul appeared soon after to compete with
#126873