Misplaced Pages

#743256

40-560: Death Road may refer to: Yungas Road , a notoriously treacherous route in Bolivia Kabul–Behsud Highway , a highway in Afghanistan noted for its frequency of Taliban-related killings Topics referred to by the same term [REDACTED] This disambiguation page lists articles associated with the title Death Road . If an internal link led you here, you may wish to change

80-406: A 2,000 kg (4,400 lb) pickup truck traveling 100 km/h (62 mph), colliding with the rail at a 25-degree angle. Flexible barriers include cable barriers and weak post corrugated guide rail systems. These are referred to as flexible barriers because they will deflect 1.6 to 2.6 m (5.2 to 8.5 ft) when struck by a typical passenger car or light truck. Impact energy

120-407: A black lid. Fitch barriers are often found in a triangular arrangement at the end of a guard rail between a highway and an exit lane (the area known as the gore ), along the most probable line of impact. The barriers in front contain the least sand, with each successive barrel containing more. When a vehicle collides with the barrels, the vehicle's kinetic energy is dissipated by the shattering of

160-452: A critical component of comprehensive security planning at nuclear facilities . The NRC's detailed guidelines on vehicle barriers demonstrate its commitment to maintaining high standards of safety and security at U.S. nuclear sites . Adherence to these regulations is crucial for mitigating risks associated with vehicle-based threats. Traffic barriers are categorized in two ways: by the function they serve, and by how much they deflect when

200-520: A formidable deterrent against potential threats, including vehicle-borne attacks and unauthorized access. Road blockers are equipped with mechanisms that allow for quick deployment and retraction when needed, providing a flexible and effective means of traffic control and security management. Platform barriers , Platform screen doors (PSDs) without the doors, are used when PSDs are not feasible due to cost, technological compatibility or other factors. Barriers are divided into three groups, based on

240-410: A greater threat to general health and well-being of the public than the obstacle it intends to protect. In many regions of the world, the concept of clear zone is taken into account when examining the distance of an obstacle or hazard from the edge of travelway. Clear zone , also known as clear recovery area or horizontal clearance is defined (through study) as a lateral distance in which a motorist on

280-420: A median and striking an oncoming vehicle in a head-on crash . Unlike roadside barriers, they must be designed to be struck from either side. Bridge barriers are designed to restrain vehicles from crashing off the side of a bridge and falling onto the roadway, river or railroad below. It is usually higher than roadside barrier, to prevent trucks, buses, pedestrians and cyclists from vaulting or rolling over

320-410: A one-sided traffic barrier. Recycled tyres had been proposed for highway crash barriers by 2012, but many governments prefer sand-filled crash barriers because they have excellent energy-absorption characteristics and are easier to erect and dismantle. A Fitch Barrier is an energy-absorbing type of impact attenuator consisting of a group of sand-filled plastic barrels, usually yellow in color with

360-462: A recoverable slope may travel outside of the travelway and return their vehicle safely to the roadway. This distance is commonly determined as the 85th percentile in a study comparable to the method of determining speed limits on roadways through speed studies and varies based on the classification of a roadway. In order to provide for adequate safety in roadside conditions, hazardous elements such as fixed obstacles or steep slopes can be placed outside of

400-420: A vehicle crashes into them. Roadside barriers are used to protect traffic from roadside obstacles or hazards, such as slopes steep enough to cause rollover crashes, fixed objects like bridge piers , and bodies of water. Roadside barriers can also be used with medians, to prevent vehicles from colliding with hazards within the median. Median barriers are used to prevent vehicles from crossing over

440-769: Is a 64-kilometre (40 mi) long cycle route linking the city of La Paz with the Yungas region of Bolivia . It was conceived in the 1930s by the Bolivian government to connect the capital city of La Paz with the Amazon Rainforest in the north part of the country. Large parts of it were built by Paraguayan prisoners during the Chaco War . Several sections of the road are less than 3 metres (9.8 ft) wide, and due to presence of rain, fog , landslides , cascades , steep slopes and cliffs that drop more than 610 meters or 2000 feet, it

SECTION 10

#1733093432744

480-552: Is composed of steel-reinforced plastic boxes that are put in place where needed, linked together to form a longitudinal barrier, then ballasted with water. These have an advantage in that they can be assembled without heavy lifting equipment, but they cannot be used in freezing weather. Road blockers are used to enhance security by preventing unauthorized or hostile vehicles from entering sensitive or protected locations, such as government buildings, military installations, airports, embassies, and high-security facilities. They act as

520-415: Is dissipated through deformation of the rail elements, posts, soil and vehicle bodywork, and friction between the rail and vehicle. Box beam systems also spread the impact force over a number of posts due to the stiffness of the steel tube. Rigid barriers are usually constructed of reinforced concrete. A permanent concrete barrier will only deflect a negligible amount when struck by a vehicle. Instead,

560-495: Is dissipated through tension in the rail elements, deformation of the rail elements, posts, soil and vehicle bodywork, and friction between the rail and vehicle. Semi-rigid barriers include box beam guide rail, heavy post blocked out corrugated guide rail and thrie-beam guide rail. Thrie-beam is similar to corrugated rail, but it has three ridges instead of two. They deflect 3 to 6 feet (0.91 to 1.83 m): more than rigid barriers, but less than flexible barriers. Impact energy

600-521: Is largely considered the most dangerous road in the world. Since 1994, nearly 300 drivers and passengers are reported to have died there annually. Unlike in the rest of the country, The Yungas Road is a left-hand traffic road, which allowed drivers to better gauge the distance between their vehicles and the edge of the road. It has since been replaced by a newer, two-lane asphalt road featuring guardrails and drainage systems. Known for its extreme danger with 3,500 metres (11,500 ft) of descent,

640-450: The "gating" feature allows the vehicles to pass through the rail as it bends. If space allows, a guide rail may also be terminated by gradually curving it back to the point that the terminal is unlikely to be hit end-on, or, if possible, by embedding the end in a hillside or cut slope. An alternative to energy absorbing barrier terminals are impact attenuators . These are used for wider hazards that cannot be effectively protected with

680-562: The Death Road draws about 25,000 tourists per year and has become a popular destination for adventure tourism , particularly mountain biking . At least 18 cyclists have died on the road since 1998. Parts of this road were built by Paraguayan prisoners that were captured after Chaco War in 1930s. It was of one of the few routes that connect the Amazon jungle up north, with the city of La Paz. A new alternative route, now part of Route 3 ,

720-520: The North Yungas Road was the sole route for traveling from Coroico to La Paz. In 2009, the Bolivian government built a new road along the adjacent mountain range. The asphalt road features two lanes, drainage systems and guardians. Because of the steep slopes, the lack of guardrails , and the narrow width of the road (as little as 3 meters in some places), the road was especially dangerous for vehicular traffic. Weather conditions further increased

760-516: The amount they deflect when struck by a vehicle and the mechanism the barrier uses to resist the impact forces. In the United States , traffic barriers are tested and classified according to the AASHTO Manual for Assessing Safety Hardware (MASH) standards, which recently superseded Federal Highway Administration NCHRP Report 350. Barrier deflections listed below are results from crash tests with

800-430: The angled lower section. For low-speed or low-angle impacts on these barriers, that may be sufficient to redirect the vehicle without damaging the bodywork. The disadvantage is there is a higher likelihood of rollover with a small car than the single slope or step barriers. Impact forces are resisted by a combination of the rigidity and mass of the barrier. Deflection is usually negligible. An early concrete barrier design

840-478: The ban in 1998 to the entire National Highway System . To address the vaulting and rollover crashes, a new type of terminals were developed. The first generation of these terminals in the 1970s were breakaway cable terminals, in which the rail curves back on itself and is connected to a cable that runs between the first and second posts (which are often breakaway posts). These barrier terminals were sometimes able to spear through small cars that hit them at exactly

SECTION 20

#1733093432744

880-429: The barrier and falling over the side of the structure. Bridge rails are usually multi-rail tubular steel barriers or reinforced concrete parapets and barriers. Work zone barriers are used to protect traffic from hazards in work zones. Their distinguishing feature is they can be relocated as conditions change in the road works. Two common types are used: temporary concrete barrier and water-filled barrier. The latter

920-468: The barrier, potentially causing the vehicle to roll over. However, along parkways and other areas where aesthetics are considered important, reinforced concrete walls with stone veneers or faux stone finishes are sometimes used. These barrier walls usually have vertical faces to prevent vehicles from climbing the barrier. For several decades after the invention of motor vehicles, designers of early traffic barriers paid little attention to their ends, so that

960-422: The barriers either ended abruptly in blunt ends, or sometimes featured some flaring of the edges away from the side of the barrier facing traffic. Vehicles that struck blunt ends at the wrong angle could stop too suddenly or suffer penetration of the passenger compartment by steel rail sections, resulting in severe injuries or fatalities. Traffic engineers have learned through such gruesome real-world experience that

1000-402: The clear zone in order to reduce or eliminate the need for roadside protection. Common sites for installation of traffic barrier: When a barrier is needed, careful calculations are completed to determine length of need. The calculations take into account the speed and volume of traffic volume using the road, the distance from the edge of travelway to the hazard, and the distance or offset from

1040-583: The danger; rain and fog would reduce visibility, while muddy terrain and loose stones could impair traction. It was famous for its dangerous conditions and deaths from traffic accidents, averaging around 209 accidents and 96 deaths per year. In 1995, the Inter-American Development Bank dubbed it as the most dangerous road in the world. In July 1983, a bus fell from the Yungas Road into a canyon, killing more than one hundred passengers in one of

1080-435: The edge of travelway to the barrier. In accordance with U.S. regulations for nuclear power plants , the U.S. Nuclear Regulatory Commission (NRC) addresses vehicle barriers under 10 CFR Part 73 , specifically in 10 CFR 73.55(e)(10) Vehicle Barriers. This section requires licensees to "use physical barriers and security strategies [via strategic planning ] to protect against land vehicle borne explosive devices ". Here,

1120-603: The ends of barriers are just as important as the barriers themselves; the American Association of State Highway and Transportation Officials devotes an entire chapter to the topic of barrier "end treatments" in its Roadsign Design Guide . In response, a new style of barrier terminals was developed in the 1960s in which the installers were directed to twist the guardrail 90 degrees and bring its end down so that it would lie flat at ground level (so-called "turned-down" terminals or "ramped ends"). While this innovation prevented

1160-573: The focus is on safeguarding the protected area and vital areas of nuclear facilities from unauthorized vehicle access, emphasizing the need for effective barrier systems against potential vehicular threats. The regulation highlights the importance of designing and implementing barriers that are robust enough to withstand various threat scenarios, including different types of vehicles and potential explosive devices . The integration of these barriers with other security measures, such as surveillance , access control , and intrusion detection systems , forms

1200-417: The link to point directly to the intended article. Retrieved from " https://en.wikipedia.org/w/index.php?title=Death_Road&oldid=1126785703 " Category : Disambiguation pages Hidden categories: Short description is different from Wikidata All article disambiguation pages All disambiguation pages Yungas Road The Yungas Road , popularly known as The Death Road,

1240-414: The opposing carriageway of traffic and help to reduce head-on collisions . Some of these barriers, designed to be struck from either side, are called median barriers. Traffic barriers can also be used to protect vulnerable areas like school yards, pedestrian zones , and fuel tanks from errant vehicles. In pedestrian zones, like school yards, they also prevent children or other pedestrians from running onto

Death Road - Misplaced Pages Continue

1280-417: The performance limits of traffic barriers and provide an adequate level of protection to road users. Roadside hazards must be assessed for the danger they pose to traveling motorists based on size, shape, rigidity, and distance from the edge of travelway. For instance, small roadside signs and some large signs (ground-mounted breakaway post) often do not merit roadside protection as the barrier itself may pose

1320-540: The rail from penetrating the vehicle, it could also vault a vehicle into the air or cause it to roll over, since the rising and twisting guardrail formed a ramp. These crashes often led to vehicles vaulting, rolling, or vaulting and rolling at high speed into the very objects which guardrails or barriers were supposed to protect them from in the first place. Such wild crashes caused the United States to ban ramped ends in 1990 on high-speed, high-volume highways, and to extend

1360-671: The road. While barriers are normally designed to minimize injury to vehicle occupants, injuries do occur in collisions with traffic barriers. They should only be installed where a collision with the barrier is likely to be less severe than a collision with the hazard behind it. Where possible, it is preferable to remove, relocate or modify a hazard, rather than shield it with a barrier. To make sure they are safe and effective, traffic barriers undergo extensive simulated and full scale crash testing before they are approved for general use. While crash testing cannot replicate every potential manner of impact, testing programs are designed to determine

1400-414: The shape of a concrete barrier is designed to redirect a vehicle into a path parallel to the barrier. This means they can be used to protect traffic from hazards very close behind the barrier, and generally require very little maintenance. Impact energy is dissipated through redirection and deformation of the vehicle itself. Jersey barriers and F-shape barriers also lift the vehicle as the tires ride up on

1440-1031: The worst road accidents in Bolivia. Until the mid-1990s, the accident rate was even worse, with 200 to 300 drivers falling off the cliff each year. In 2011, the total number of accidents was around 114, the second most in Bolivia after the road between La Paz and Oruro . Of these accidents, 42 people died. Traffic barrier Traffic barriers (known in North America as guardrails or guard rails , in Britain as crash barriers , and in auto racing as Armco barriers ) keep vehicles within their roadway and prevent them from colliding with dangerous obstacles such as boulders, sign supports, trees, bridge abutments, buildings, walls, and large storm drains , or from traversing steep (non-recoverable) slopes or entering deep water. They are also installed within medians of divided highways to prevent errant vehicles from entering

1480-520: The wrong angle and were deprecated in 1993. The second generation of these terminals, called energy-absorbing terminals, was developed in the 1990s and 2000s. The goal was to develop a kinetic energy dissipating system soft enough for small vehicles to decelerate without causing the guardrail to spear through them, but firm enough to stop larger vehicles. The energy dissipation could be done through bending, kinking, crushing, or deforming guardrail elements. The first family of energy-absorbing terminal products

1520-411: Was built during a 20-year period ending in 2006. The modernization included enlarging the carriageway from one to two lanes; asphalt paving; bridges, drainage, guardrails, and the building of a new section between Chusquipata and Yolosa , bypassing the most dangerous sections of the original road. As the result, North Yungas Road is now mainly used for bicycles, motorcycles, and walking. Up until 2006,

1560-522: Was developed by the New Jersey State Highway Department. This led to the term Jersey barrier being used as a generic term, although technically it applies to a specific shape of concrete barrier. Other types include constant-slope barriers , concrete step barriers , and F-shape barriers . Concrete barriers usually have smooth finishes. At some impact angles, coarse finishes allow the drive wheel of front wheel drive vehicles to climb

1600-410: Was the extruding terminal type. It features a large steel impact head that engages the frame or bumper of the vehicle in head-on collisions. The impact head is driven back along the guide rail, dissipating the vehicle's kinetic energy by bending or tearing the steel in the guide rail sections away to the side to prevent spearing. When the terminals are hit in an angle, they dissipate much of the energy but

#743256