Misplaced Pages

#695304

125-558: First opened to traffic in 1884, it was a major engineering achievement of the nation, being the longest railway tunnel in Austria for over 100 years, possessing a length of 10,216 metres (6.348 mi). Originally operated by steam locomotives , the Arlberg Railway Tunnel was reengineered during the 1920s for use by electric traction. During the 2010s, further modifications were implemented to introduce improved safety levels and expand

250-462: A tender coupled to it. Variations in this general design include electrically powered boilers, turbines in place of pistons, and using steam generated externally. Steam locomotives were first developed in the United Kingdom during the early 19th century and used for railway transport until the middle of the 20th century. Richard Trevithick built the first steam locomotive known to have hauled

375-635: A (newly identified) Killingworth Billy in 1816. He also constructed The Duke in 1817 for the Kilmarnock and Troon Railway , which was the first steam locomotive to work in Scotland. In 1825, Stephenson built Locomotion No. 1 for the Stockton and Darlington Railway , north-east England, which was the first public steam railway in the world. In 1829, his son Robert built in Newcastle The Rocket , which

500-448: A balance has to be struck between obtaining sufficient draught for combustion whilst giving the exhaust gases and particles sufficient time to be consumed. In the past, a strong draught could lift the fire off the grate, or cause the ejection of unburnt particles of fuel, dirt and pollution for which steam locomotives had an unenviable reputation. Moreover, the pumping action of the exhaust has the counter-effect of exerting back pressure on

625-480: A conventional diesel or electric locomotive would be unsuitable. An example is maintenance trains on electrified lines when the electricity supply is turned off. Another use is in industrial facilities where a combustion-powered locomotive (i.e., steam- or diesel-powered ) could cause a safety issue due to the risks of fire, explosion or fumes in a confined space. Battery locomotives are preferred for mines where gas could be ignited by trolley-powered units arcing at

750-483: A crankpin on the driving wheel ( Main driver in the US) or to a crank on a driving axle. The movement of the valves in the steam chest is controlled through a set of rods and linkages called the valve gear , actuated from the driving axle or from the crankpin; the valve gear includes devices that allow reversing the engine, adjusting valve travel and the timing of the admission and exhaust events. The cut-off point determines

875-566: A critical piece of infrastructure for the Austrian Federal Railways. Up to 90 trains per day were reportedly using the route on busy days by 2009, resulting in several million tonnes of freight traversing the tunnel during a single year. The top speed in the tunnel is 100 km/h. During the early twenty-first century, the Austrian Federal Railways began to reengineer elements of the Arlberg line with contemporary safety features. As such,

1000-438: A deployable "water scoop" fitted under the tender or the rear water tank in the case of a large tank engine; the fireman remotely lowered the scoop into the trough, the speed of the engine forced the water up into the tank, and the scoop was raised again once it was full. Water is essential for the operation of a steam locomotive. As Swengel argued: Locomotive A locomotive is a rail transport vehicle that provides

1125-417: A desire to keep the existing tunnel structure relatively intact, avoiding lengthy interruptions to operations; however, the safety measures introduced maintained compliance with existing guidelines and knowhow. Furthermore, the loading gauge throughout the tunnel was expanded by lowering the track bed, while a permanent road surface was also added so that emergency vehicles could more readily move inside as well;

1250-458: A diesel–electric locomotive ( E 2 original number Юэ 001/Yu-e 001) started operations. It had been designed by a team led by Yury Lomonosov and built 1923–1924 by Maschinenfabrik Esslingen in Germany. It had 5 driving axles (1'E1'). After several test rides, it hauled trains for almost three decades from 1925 to 1954. An electric locomotive is a locomotive powered only by electricity. Electricity

1375-429: A gauge mounted in the cab. Steam pressure can be released manually by the driver or fireman. If the pressure reaches the boiler's design working limit, a safety valve opens automatically to reduce the pressure and avoid a catastrophic accident. The exhaust steam from the engine cylinders shoots out of a nozzle pointing up the chimney in the smokebox. The steam entrains or drags the smokebox gases with it which maintains

SECTION 10

#1733084952696

1500-423: A ground and polished journal that is integral to the axle. The other side of the housing has a tongue-shaped protuberance that engages a matching slot in the truck (bogie) bolster, its purpose being to act as a torque reaction device, as well as a support. Power transfer from motor to axle is effected by spur gearing , in which a pinion on the motor shaft engages a bull gear on the axle. Both gears are enclosed in

1625-410: A high ride quality and less electrical equipment; but EMUs have less axle weight, which reduces maintenance costs, and EMUs also have higher acceleration and higher seating capacity. Also some trains, including TGV PSE , TGV TMST and TGV V150 , use both non-passenger power cars and additional passenger motor cars. Locomotives occasionally work in a specific role, such as: The wheel arrangement of

1750-547: A higher power-to-weight ratio than DC motors and, because of the absence of a commutator , were simpler to manufacture and maintain. However, they were much larger than the DC motors of the time and could not be mounted in underfloor bogies : they could only be carried within locomotive bodies. In 1894, Hungarian engineer Kálmán Kandó developed a new type 3-phase asynchronous electric drive motors and generators for electric locomotives. Kandó's early 1894 designs were first applied in

1875-488: A larger locomotive named Galvani , exhibited at the Royal Scottish Society of Arts Exhibition in 1841. The seven-ton vehicle had two direct-drive reluctance motors , with fixed electromagnets acting on iron bars attached to a wooden cylinder on each axle, and simple commutators . It hauled a load of six tons at four miles per hour (6 kilometers per hour) for a distance of one and a half miles (2.4 kilometres). It

2000-410: A liquid-tight housing containing lubricating oil. The type of service in which the locomotive is used dictates the gear ratio employed. Numerically high ratios are commonly found on freight units, whereas numerically low ratios are typical of passenger engines. Electricity is typically generated in large and relatively efficient generating stations , transmitted to the railway network and distributed to

2125-494: A load over a distance at Pen-y-darren in 1804, although he produced an earlier locomotive for trial at Coalbrookdale in 1802. Salamanca , built in 1812 by Matthew Murray for the Middleton Railway , was the first commercially successful steam locomotive. Locomotion No. 1 , built by George Stephenson and his son Robert's company Robert Stephenson and Company , was the first steam locomotive to haul passengers on

2250-483: A locomotive describes how many wheels it has; common methods include the AAR wheel arrangement , UIC classification , and Whyte notation systems. In the second half of the twentieth century remote control locomotives started to enter service in switching operations, being remotely controlled by an operator outside of the locomotive cab. The main benefit is one operator can control the loading of grain, coal, gravel, etc. into

2375-481: A lower pressure in the smokebox than that under the firebox grate. This pressure difference causes air to flow up through the coal bed and keeps the fire burning. The search for thermal efficiency greater than that of a typical fire-tube boiler led engineers, such as Nigel Gresley , to consider the water-tube boiler . Although he tested the concept on the LNER Class W1 , the difficulties during development exceeded

2500-433: A lower reciprocating mass than three, four, five or six coupled axles. They were thus able to turn at very high speeds due to the lower reciprocating mass. A trailing axle was able to support a huge firebox, hence most locomotives with the wheel arrangement of 4-4-2 (American Type Atlantic) were called free steamers and were able to maintain steam pressure regardless of throttle setting. The chassis, or locomotive frame ,

2625-630: A number of Swiss steam shunting locomotives were modified to use electrically heated boilers, consuming around 480 kW of power collected from an overhead line with a pantograph . These locomotives were significantly less efficient than electric ones ; they were used because Switzerland was suffering a coal shortage because of the War, but had access to plentiful hydroelectricity . A number of tourist lines and heritage locomotives in Switzerland, Argentina and Australia have used light diesel-type oil. Water

SECTION 20

#1733084952696

2750-404: A number of important innovations including the use of high-pressure steam which reduced the weight of the engine and increased its efficiency. In 1812, Matthew Murray 's twin-cylinder rack locomotive Salamanca first ran on the edge-railed rack-and-pinion Middleton Railway ; this is generally regarded as the first commercially successful locomotive. Another well-known early locomotive

2875-456: A number of important innovations that included using high-pressure steam which reduced the weight of the engine and increased its efficiency. Trevithick visited the Newcastle area in 1804 and had a ready audience of colliery (coal mine) owners and engineers. The visit was so successful that the colliery railways in north-east England became the leading centre for experimentation and development of

3000-455: A public railway, the Stockton and Darlington Railway , in 1825. Rapid development ensued; in 1830 George Stephenson opened the first public inter-city railway, the Liverpool and Manchester Railway , after the success of Rocket at the 1829 Rainhill Trials had proved that steam locomotives could perform such duties. Robert Stephenson and Company was the pre-eminent builder of steam locomotives in

3125-459: A rigid frame with a 30% weight reduction. Generally, the largest locomotives are permanently coupled to a tender that carries the water and fuel. Often, locomotives working shorter distances do not have a tender and carry the fuel in a bunker, with the water carried in tanks placed next to the boiler. The tanks can be in various configurations, including two tanks alongside ( side tanks or pannier tanks ), one on top ( saddle tank ) or one between

3250-403: A separate fourth rail for this purpose. The type of electrical power used is either direct current (DC) or alternating current (AC). Various collection methods exist: a trolley pole , which is a long flexible pole that engages the line with a wheel or shoe; a bow collector , which is a frame that holds a long collecting rod against the wire; a pantograph , which is a hinged frame that holds

3375-476: A short three-phase AC tramway in Evian-les-Bains (France), which was constructed between 1896 and 1898. In 1918, Kandó invented and developed the rotary phase converter , enabling electric locomotives to use three-phase motors whilst supplied via a single overhead wire, carrying the simple industrial frequency (50 Hz) single phase AC of the high voltage national networks. In 1896, Oerlikon installed

3500-522: A significantly larger workforce is required to operate and service them. British Rail figures showed that the cost of crewing and fuelling a steam locomotive was about two and a half times larger than the cost of supporting an equivalent diesel locomotive, and the daily mileage they could run was lower. Between about 1950 and 1970, the majority of steam locomotives were retired from commercial service and replaced with electric and diesel–electric locomotives. While North America transitioned from steam during

3625-401: A tank in the locomotive tender or wrapped around the boiler in the case of a tank locomotive . Periodic stops are required to refill the tanks; an alternative was a scoop installed under the tender that collected water as the train passed over a track pan located between the rails. While the locomotive is producing steam, the amount of water in the boiler is constantly monitored by looking at

3750-456: Is common to classify locomotives by their source of energy. The common ones include: A steam locomotive is a locomotive whose primary power source is a steam engine . The most common form of steam locomotive also contains a boiler to generate the steam used by the engine. The water in the boiler is heated by burning combustible material – usually coal, wood, or oil – to produce steam. The steam moves reciprocating pistons which are connected to

3875-475: Is crucial to the efficiency of any steam locomotive, and the internal profiles of the chimney (or, strictly speaking, the ejector ) require careful design and adjustment. This has been the object of intensive studies by a number of engineers (and often ignored by others, sometimes with catastrophic consequences). The fact that the draught depends on the exhaust pressure means that power delivery and power generation are automatically self-adjusting. Among other things,

Arlberg Railway Tunnel - Misplaced Pages Continue

4000-419: Is directed upwards out of the locomotive through the chimney, by way of a nozzle called a blastpipe , creating the familiar "chuffing" sound of the steam locomotive. The blastpipe is placed at a strategic point inside the smokebox that is at the same time traversed by the combustion gases drawn through the boiler and grate by the action of the steam blast. The combining of the two streams, steam and exhaust gases,

4125-416: Is supplied to moving trains with a (nearly) continuous conductor running along the track that usually takes one of three forms: an overhead line , suspended from poles or towers along the track or from structure or tunnel ceilings; a third rail mounted at track level; or an onboard battery . Both overhead wire and third-rail systems usually use the running rails as the return conductor but some systems use

4250-516: Is that these power cars are integral part of a train and are not adapted for operation with any other types of passenger coaches. On the other hand, many high-speed trains such as the Shinkansen network never use locomotives. Instead of locomotive-like power-cars, they use electric multiple units (EMUs) or diesel multiple units (DMUs) – passenger cars that also have traction motors and power equipment. Using dedicated locomotive-like power cars allows for

4375-415: Is the principal structure onto which the boiler is mounted and which incorporates the various elements of the running gear. The boiler is rigidly mounted on a "saddle" beneath the smokebox and in front of the boiler barrel, but the firebox at the rear is allowed to slide forward and backwards, to allow for expansion when hot. European locomotives usually use "plate frames", where two vertical flat plates form

4500-874: The Drache , was delivered in 1848. The first steam locomotives operating in Italy were the Bayard and the Vesuvio , running on the Napoli-Portici line, in the Kingdom of the Two Sicilies. The first railway line over Swiss territory was the Strasbourg – Basel line opened in 1844. Three years later, in 1847, the first fully Swiss railway line, the Spanisch Brötli Bahn , from Zürich to Baden

4625-585: The EMD FL9 and Bombardier ALP-45DP There are three main uses of locomotives in rail transport operations : for hauling passenger trains, freight trains, and for switching (UK English: shunting). Freight locomotives are normally designed to deliver high starting tractive effort and high sustained power. This allows them to start and move long, heavy trains, but usually comes at the cost of relatively low maximum speeds. Passenger locomotives usually develop lower starting tractive effort but are able to operate at

4750-667: The Medieval Latin motivus 'causing motion', and is a shortened form of the term locomotive engine , which was first used in 1814 to distinguish between self-propelled and stationary steam engines . Prior to locomotives, the motive force for railways had been generated by various lower-technology methods such as human power, horse power, gravity or stationary engines that drove cable systems. Few such systems are still in existence today. Locomotives may generate their power from fuel (wood, coal, petroleum or natural gas), or they may take power from an outside source of electricity. It

4875-574: The Ohio Historical Society Museum in Columbus, US. The authenticity and date of this locomotive is disputed by some experts and a workable steam train would have to await the invention of the high-pressure steam engine by Richard Trevithick , who pioneered the use of steam locomotives. The first full-scale working railway steam locomotive was the 3 ft ( 914 mm ) gauge Coalbrookdale Locomotive built by Trevithick in 1802. It

5000-417: The loading gauge . It is interconnected with the later-built Arlberg Road Tunnel . The origins of the Arlberg Railway Tunnel is closely associated with the Arlberg railway, of which construction commenced immediately after receiving authorisation to proceed on 16 May 1880. Built at a total cost of 35.5 million gulden, the line had been approved as a single-track railway throughout much of its length; however,

5125-413: The motive power for a train . If a locomotive is capable of carrying a payload, it is usually rather referred to as a multiple unit , motor coach , railcar or power car ; the use of these self-propelled vehicles is increasingly common for passenger trains , but rare for freight trains . Traditionally, locomotives pulled trains from the front. However, push-pull operation has become common, where

Arlberg Railway Tunnel - Misplaced Pages Continue

5250-500: The traction motors and axles adapts the power output to the rails for freight or passenger service. Passenger locomotives may include other features, such as head-end power (also referred to as hotel power or electric train supply) or a steam generator . Some locomotives are designed specifically to work steep grade railways , and feature extensive additional braking mechanisms and sometimes rack and pinion. Steam locomotives built for steep rack and pinion railways frequently have

5375-408: The 1950s, and continental Europe by the 1970s, in other parts of the world, the transition happened later. Steam was a familiar technology that used widely-available fuels and in low-wage economies did not suffer as wide a cost disparity. It continued to be used in many countries until the end of the 20th century. By the end of the 20th century, almost the only steam power remaining in regular use around

5500-492: The 1970s, the interconnecting Arlberg Road Tunnel was built alongside the earlier railway tunnel, there is a minimum distance of 150 distances between the actively-trafficked bores. In 2001 a new railway station in St. Anton was opened, and the tunnel was built 434 metres longer to east. For over 125 years, the tunnel has functioned as the only railway connection between the two Austrian provinces of Tyrol and Vorarlberg ; making it

5625-630: The 40 km Burgdorf—Thun line , Switzerland. The first implementation of industrial frequency single-phase AC supply for locomotives came from Oerlikon in 1901, using the designs of Hans Behn-Eschenburg and Emil Huber-Stockar ; installation on the Seebach-Wettingen line of the Swiss Federal Railways was completed in 1904. The 15 kV, 50 Hz 345 kW (460 hp), 48 tonne locomotives used transformers and rotary converters to power DC traction motors. Italian railways were

5750-467: The Arlberg Railway Tunnel was subject to a package of works costing 210 million euros during a temporary closure, this included the addition of eight new evacuation and rescue passaged between it and the adjacent Arlberg Road Tunnel; other safety-related changes included a water supply (for fire-fighting purposes), new orientation lighting, emergency telephone and radio facilities, and overhead line disconnection functionality. These alterations were tempered by

5875-492: The Arlberg tunnel was intentionally constructed with sufficient space to accommodate a double track arrangement from the onset, engineers having anticipated the need to handle higher volumes of traffic than a single line would be able to convey. A large proportion of the Arlberg Railway Tunnel, akin to much of the line's engineered features, comprised natural stone masonry in its construction, using materials such as limestone , gneiss , and mica schist . The Arlberg Railway Tunnel

6000-564: The Saar (today part of Völklingen ), but neither could be returned to working order after being dismantled, moved and reassembled. On 7 December 1835, the Adler ran for the first time between Nuremberg and Fürth on the Bavarian Ludwig Railway . It was the 118th engine from the locomotive works of Robert Stephenson and stood under patent protection. In Russia , the first steam locomotive

6125-423: The US), or screw-reverser (if so equipped), that controls the cut-off, therefore, performs a similar function to a gearshift in an automobile – maximum cut-off, providing maximum tractive effort at the expense of efficiency, is used to pull away from a standing start, whilst a cut-off as low as 10% is used when cruising, providing reduced tractive effort, and therefore lower fuel/water consumption. Exhaust steam

6250-721: The United Kingdom was a petrol–mechanical locomotive built by the Maudslay Motor Company in 1902, for the Deptford Cattle Market in London . It was an 80 hp locomotive using a three-cylinder vertical petrol engine, with a two speed mechanical gearbox. Diesel locomotives are powered by diesel engines . In the early days of diesel propulsion development, various transmission systems were employed with varying degrees of success, with electric transmission proving to be

6375-655: The United States, including John Fitch's miniature prototype. A prominent full sized example was Col. John Steven's "steam wagon" which was demonstrated on a loop of track in Hoboken, New Jersey in 1825. Many of the earliest locomotives for commercial use on American railroads were imported from Great Britain, including first the Stourbridge Lion and later the John Bull . However, a domestic locomotive-manufacturing industry

SECTION 50

#1733084952696

6500-545: The adhesive weight. Equalising beams connecting the ends of leaf springs have often been deemed a complication in Britain, however, locomotives fitted with the beams have usually been less prone to loss of traction due to wheel-slip. Suspension using equalizing levers between driving axles, and between driving axles and trucks, was standard practice on North American locomotives to maintain even wheel loads when operating on uneven track. Locomotives with total adhesion, where all of

6625-402: The boiler materials to the point where it needs to be rebuilt or replaced. Start-up on a large engine may take hours of preliminary heating of the boiler water before sufficient steam is available. Although the boiler is typically placed horizontally, for locomotives designed to work in locations with steep slopes it may be more appropriate to consider a vertical boiler or one mounted such that

6750-404: The boiler remains horizontal but the wheels are inclined to suit the slope of the rails. The steam generated in the boiler fills the space above the water in the partially filled boiler. Its maximum working pressure is limited by spring-loaded safety valves. It is then collected either in a perforated tube fitted above the water level or by a dome that often houses the regulator valve, or throttle,

6875-808: The boiler tilted relative to the locomotive frame , so that the boiler remains roughly level on steep grades. Locomotives are also used on some high-speed trains. Some of them are operated in push-pull formation with trailer control cars at another end of a train, which often have a cabin with the same design as a cabin of locomotive; examples of such trains with conventional locomotives are Railjet and Intercity 225 . Also many high-speed trains, including all TGV , many Talgo (250 / 350 / Avril / XXI), some Korea Train Express , ICE 1 / ICE 2 and Intercity 125 , use dedicated power cars , which do not have places for passengers and technically are special single-ended locomotives. The difference from conventional locomotives

7000-399: The boiler. Boiler water surrounds the firebox to stop the metal from becoming too hot. This is another area where the gas transfers heat to the water and is called the firebox heating surface. Ash and char collect in the smokebox as the gas gets drawn up the chimney ( stack or smokestack in the US) by the exhaust steam from the cylinders. The pressure in the boiler has to be monitored using

7125-460: The center section would have a 200-ton reactor chamber and steel walls 5 feet thick to prevent releases of radioactivity in case of accidents. He estimated a cost to manufacture atomic locomotives with 7000 h.p. engines at approximately $ 1,200,000 each. Consequently, trains with onboard nuclear generators were generally deemed unfeasible due to prohibitive costs. In 2002, the first 3.6 tonne, 17 kW hydrogen (fuel cell) -powered mining locomotive

7250-407: The collecting shoes against the wire in a fixed geometry; or a contact shoe , which is a shoe in contact with the third rail. Of the three, the pantograph method is best suited for high-speed operation. Electric locomotives almost universally use axle-hung traction motors, with one motor for each powered axle. In this arrangement, one side of the motor housing is supported by plain bearings riding on

7375-455: The collection shoes, or where electrical resistance could develop in the supply or return circuits, especially at rail joints, and allow dangerous current leakage into the ground. Battery locomotives in over-the-road service can recharge while absorbing dynamic-braking energy. The first known electric locomotive was built in 1837 by chemist Robert Davidson of Aberdeen , and it was powered by galvanic cells (batteries). Davidson later built

7500-720: The dominant fuel worldwide in steam locomotives. Railways serving sugar cane farming operations burned bagasse , a byproduct of sugar refining. In the US, the ready availability and low price of oil made it a popular steam locomotive fuel after 1900 for the southwestern railroads, particularly the Southern Pacific. In the Australian state of Victoria, many steam locomotives were converted to heavy oil firing after World War II. German, Russian, Australian and British railways experimented with using coal dust to fire locomotives. During World War 2,

7625-405: The driving wheels by means of connecting rods, with no intervening gearbox. This means the combination of starting tractive effort and maximum speed is greatly influenced by the diameter of the driving wheels. Steam locomotives intended for freight service generally have smaller diameter driving wheels than passenger locomotives. In diesel–electric and electric locomotives the control system between

SECTION 60

#1733084952696

7750-514: The early 1950s, Lyle Borst of the University of Utah was given funding by various US railroad line and manufacturers to study the feasibility of an electric-drive locomotive, in which an onboard atomic reactor produced the steam to generate the electricity. At that time, atomic power was not fully understood; Borst believed the major stumbling block was the price of uranium. With the Borst atomic locomotive,

7875-431: The exhaust gas volume was vented through a cooling tower, allowing the steam exhaust to draw more air past the radiator. Running gear includes the brake gear, wheel sets , axleboxes , springing and the motion that includes connecting rods and valve gear. The transmission of the power from the pistons to the rails and the behaviour of the locomotive as a vehicle, being able to negotiate curves, points and irregularities in

8000-448: The firebox becomes exposed. Without water on top of the sheet to transfer away the heat of combustion , it softens and fails, letting high-pressure steam into the firebox and the cab. The development of the fusible plug , a temperature-sensitive device, ensured a controlled venting of steam into the firebox to warn the fireman to add water. Scale builds up in the boiler and prevents adequate heat transfer, and corrosion eventually degrades

8125-513: The first commercial example of the system on the Lugano Tramway . Each 30-tonne locomotive had two 110 kW (150 hp) motors run by three-phase 750 V 40 Hz fed from double overhead lines. Three-phase motors run at constant speed and provide regenerative braking , and are well suited to steeply graded routes, and the first main-line three-phase locomotives were supplied by Brown (by then in partnership with Walter Boveri ) in 1899 on

8250-495: The first decades of steam for railways in the United Kingdom, the United States, and much of Europe. Towards the end of the steam era, a longstanding British emphasis on speed culminated in a record, still unbroken, of 126 miles per hour (203 kilometres per hour) by LNER Class A4 4468 Mallard , however there are long-standing claims that the Pennsylvania Railroad class S1 achieved speeds upwards of 150 mph, though this

8375-510: The first in the world to introduce electric traction for the entire length of a main line rather than just a short stretch. The 106 km Valtellina line was opened on 4 September 1902, designed by Kandó and a team from the Ganz works. The electrical system was three-phase at 3 kV 15 Hz. The voltage was significantly higher than used earlier and it required new designs for electric motors and switching devices. The three-phase two-wire system

8500-504: The frames ( well tank ). The fuel used depended on what was economically available to the railway. In the UK and other parts of Europe, plentiful supplies of coal made this the obvious choice from the earliest days of the steam engine. Until 1870, the majority of locomotives in the United States burned wood, but as the Eastern forests were cleared, coal gradually became more widely used until it became

8625-418: The grate into an ashpan. If oil is used as the fuel, a door is needed for adjusting the air flow, maintaining the firebox, and cleaning the oil jets. The fire-tube boiler has internal tubes connecting the firebox to the smokebox through which the combustion gases flow transferring heat to the water. All the tubes together provide a large contact area, called the tube heating surface, between the gas and water in

8750-400: The high speeds required to maintain passenger schedules. Mixed-traffic locomotives (US English: general purpose or road switcher locomotives) meant for both passenger and freight trains do not develop as much starting tractive effort as a freight locomotive but are able to haul heavier trains than a passenger locomotive. Most steam locomotives have reciprocating engines, with pistons coupled to

8875-577: The highly mineralised water was available, and locomotive boilers were lasting less than a quarter of the time normally expected. In the days of steam locomotion, about half the total train load was water for the engine. The line's operator, Commonwealth Railways , was an early adopter of the diesel-electric locomotive . The fire-tube boiler was standard practice for steam locomotive. Although other types of boiler were evaluated they were not widely used, except for some 1,000 locomotives in Hungary which used

9000-452: The late 1930s. The majority of steam locomotives were retired from regular service by the 1980s, although several continue to run on tourist and heritage lines. The earliest railways employed horses to draw carts along rail tracks . In 1784, William Murdoch , a Scottish inventor, built a small-scale prototype of a steam road locomotive in Birmingham . A full-scale rail steam locomotive

9125-657: The locomotive ran on a circular track in the factory yard. It was the first locomotive to be built on the European mainland and the first steam-powered passenger service; curious onlookers could ride in the attached coaches for a fee. It is portrayed on a New Year's badge for the Royal Foundry dated 1816. Another locomotive was built using the same system in 1817. They were to be used on pit railways in Königshütte and in Luisenthal on

9250-421: The locomotive's boiler to the point where it becomes gaseous and its volume increases 1,700 times. Functionally, it is a steam engine on wheels. In most locomotives, the steam is admitted alternately to each end of its cylinders in which pistons are mechanically connected to the locomotive's main wheels. Fuel and water supplies are usually carried with the locomotive, either on the locomotive itself or in

9375-441: The locomotive's main wheels, known as the " driving wheels ". Both fuel and water supplies are carried with the locomotive, either on the locomotive itself, in bunkers and tanks , (this arrangement is known as a " tank locomotive ") or pulled behind the locomotive, in tenders , (this arrangement is known as a " tender locomotive "). The first full-scale working railway steam locomotive was built by Richard Trevithick in 1802. It

9500-656: The locomotives were retired shortly afterward. All four locomotives were donated to museums, but one was scrapped. The others can be seen at the Boone and Scenic Valley Railroad , Iowa, and at the Western Railway Museum in Rio Vista, California. The Toronto Transit Commission previously operated a battery electric locomotive built by Nippon Sharyo in 1968 and retired in 2009. London Underground regularly operates battery–electric locomotives for general maintenance work. In

9625-403: The main chassis, with a variety of spacers and a buffer beam at each end to form a rigid structure. When inside cylinders are mounted between the frames, the plate frames are a single large casting that forms a major support element. The axleboxes slide up and down to give some sprung suspension, against thickened webs attached to the frame, called "hornblocks". American practice for many years

9750-509: The mainframes. Locomotives with multiple coupled-wheels on a rigid chassis would have unacceptable flange forces on tight curves giving excessive flange and rail wear, track spreading and wheel climb derailments. One solution was to remove or thin the flanges on an axle. More common was to give axles end-play and use lateral motion control with spring or inclined-plane gravity devices. Railroads generally preferred locomotives with fewer axles, to reduce maintenance costs. The number of axles required

9875-470: The moment when the valve blocks a steam port, "cutting off" admission steam and thus determining the proportion of the stroke during which steam is admitted into the cylinder; for example a 50% cut-off admits steam for half the stroke of the piston. The remainder of the stroke is driven by the expansive force of the steam. Careful use of cut-off provides economical use of steam and in turn, reduces fuel and water consumption. The reversing lever ( Johnson bar in

10000-494: The most popular. In 1914, Hermann Lemp , a General Electric electrical engineer, developed and patented a reliable direct current electrical control system (subsequent improvements were also patented by Lemp). Lemp's design used a single lever to control both engine and generator in a coordinated fashion, and was the prototype for all diesel–electric locomotive control. In 1917–18, GE produced three experimental diesel–electric locomotives using Lemp's control design. In 1924,

10125-769: The original John Bull was on static display in the National Museum of American History in Washington, D.C. The replica is preserved at the Railroad Museum of Pennsylvania . The first railway service outside the United Kingdom and North America was opened in 1829 in France between Saint-Etienne and Lyon ; it was initially limited to animal traction and converted to steam traction early 1831, using Seguin locomotives . The first steam locomotive in service in Europe outside of France

10250-468: The piston in turn. In a two-cylinder locomotive, one cylinder is located on each side of the vehicle. The cranks are set 90° out of phase. During a full rotation of the driving wheel, steam provides four power strokes; each cylinder receives two injections of steam per revolution. The first stroke is to the front of the piston and the second stroke to the rear of the piston; hence two working strokes. Consequently, two deliveries of steam onto each piston face in

10375-665: The power supply of choice for subways, abetted by the Sprague's invention of multiple-unit train control in 1897. The first use of electrification on a main line was on a four-mile stretch of the Baltimore Belt Line of the Baltimore & Ohio (B&O) in 1895 connecting the main portion of the B&;O to the new line to New York through a series of tunnels around the edges of Baltimore's downtown. Three Bo+Bo units were initially used, at

10500-411: The purpose of which is to control the amount of steam leaving the boiler. The steam then either travels directly along and down a steam pipe to the engine unit or may first pass into the wet header of a superheater , the role of the latter being to improve thermal efficiency and eliminate water droplets suspended in the "saturated steam", the state in which it leaves the boiler. On leaving the superheater,

10625-450: The renovated tunnel was put back into service during late 2010. 47°7′43″N 10°11′8″E  /  47.12861°N 10.18556°E  / 47.12861; 10.18556 Steam locomotive A steam locomotive is a locomotive that provides the force to move itself and other vehicles by means of the expansion of steam . It is fuelled by burning combustible material (usually coal , oil or, rarely, wood ) to heat water in

10750-418: The side of the piston receiving steam, thus slightly reducing cylinder power. Designing the exhaust ejector became a specific science, with engineers such as Chapelon , Giesl and Porta making large improvements in thermal efficiency and a significant reduction in maintenance time and pollution. A similar system was used by some early gasoline/kerosene tractor manufacturers ( Advance-Rumely / Hart-Parr ) –

10875-425: The south end of the electrified section; they coupled onto the locomotive and train and pulled it through the tunnels. DC was used on earlier systems. These systems were gradually replaced by AC. Today, almost all main-line railways use AC systems. DC systems are confined mostly to urban transit such as metro systems, light rail and trams, where power requirement is less. The first practical AC electric locomotive

11000-504: The steam exits the dry header of the superheater and passes down a steam pipe, entering the steam chests adjacent to the cylinders of a reciprocating engine. Inside each steam chest is a sliding valve that distributes the steam via ports that connect the steam chest to the ends of the cylinder space. The role of the valves is twofold: admission of each fresh dose of steam, and exhaust of the used steam once it has done its work. The cylinders are double-acting, with steam admitted to each side of

11125-469: The steam locomotive. Trevithick continued his own steam propulsion experiments through another trio of locomotives, concluding with the Catch Me Who Can in 1808, first in the world to haul fare-paying passengers. In 1812, Matthew Murray 's successful twin-cylinder rack locomotive Salamanca first ran on the edge-railed rack-and-pinion Middleton Railway . Another well-known early locomotive

11250-434: The track, is of paramount importance. Because reciprocating power has to be directly applied to the rail from 0 rpm upwards, this creates the problem of adhesion of the driving wheels to the smooth rail surface. Adhesive weight is the portion of the locomotive's weight bearing on the driving wheels. This is made more effective if a pair of driving wheels is able to make the most of its axle load, i.e. its individual share of

11375-450: The train may have a locomotive (or locomotives) at the front, at the rear, or at each end. Most recently railroads have begun adopting DPU or distributed power. The front may have one or two locomotives followed by a mid-train locomotive that is controlled remotely from the lead unit. The word locomotive originates from the Latin loco 'from a place', ablative of locus 'place', and

11500-464: The trains. Some electric railways have their own dedicated generating stations and transmission lines but most purchase power from an electric utility . The railway usually provides its own distribution lines, switches and transformers . Electric locomotives usually cost 20% less than diesel locomotives, their maintenance costs are 25–35% lower, and cost up to 50% less to run. The earliest systems were DC systems. The first electric passenger train

11625-406: The tunnel's lack of ventilation; the combination of steam locomotives and inadequate air flow led to dangerous sulphuric acid vapour accumulating along the roof, which compelled locomotive crews to lie on the floor seeking fresher air to breath. While protective equipment was issued to the crews, the problem was not truly eliminated until the introduction of electric traction during the 1920s. During

11750-433: The two cylinders generates a full revolution of the driving wheel. Each piston is attached to the driving axle on each side by a connecting rod, and the driving wheels are connected together by coupling rods to transmit power from the main driver to the other wheels. Note that at the two " dead centres ", when the connecting rod is on the same axis as the crankpin on the driving wheel, the connecting rod applies no torque to

11875-419: The water level in a transparent tube, or sight glass. Efficient and safe operation of the boiler requires keeping the level in between lines marked on the sight glass. If the water level is too high, steam production falls, efficiency is lost and water is carried out with the steam into the cylinders, possibly causing mechanical damage. More seriously, if the water level gets too low, the crown sheet (top sheet) of

12000-401: The water-tube Brotan boiler . A boiler consists of a firebox where the fuel is burned, a barrel where water is turned into steam, and a smokebox which is kept at a slightly lower pressure than outside the firebox. Solid fuel, such as wood, coal or coke, is thrown into the firebox through a door by a fireman , onto a set of grates which hold the fuel in a bed as it burns. Ash falls through

12125-408: The wheel. Therefore, if both cranksets could be at "dead centre" at the same time, and the wheels should happen to stop in this position, the locomotive could not start moving. Therefore, the crankpins are attached to the wheels at a 90° angle to each other, so only one side can be at dead centre at a time. Each piston transmits power through a crosshead , connecting rod ( Main rod in the US) and

12250-411: The wheels are coupled together, generally lack stability at speed. To counter this, locomotives often fit unpowered carrying wheels mounted on two-wheeled trucks or four-wheeled bogies centred by springs/inverted rockers/geared rollers that help to guide the locomotive through curves. These usually take on weight – of the cylinders at the front or the firebox at the rear – when the width exceeds that of

12375-406: The will to increase efficiency by that route. The steam generated in the boiler not only moves the locomotive, but is also used to operate other devices such as the whistle, the air compressor for the brakes, the pump for replenishing the water in the boiler and the passenger car heating system. The constant demand for steam requires a periodic replacement of water in the boiler. The water is kept in

12500-794: The world also runs in Austria: the GKB 671 built in 1860, has never been taken out of service, and is still used for special excursions. In 1838, the third steam locomotive to be built in Germany, the Saxonia , was manufactured by the Maschinenbaufirma Übigau near Dresden , built by Prof. Johann Andreas Schubert . The first independently designed locomotive in Germany was the Beuth , built by August Borsig in 1841. The first locomotive produced by Henschel-Werke in Kassel ,

12625-433: The world was on heritage railways . Internal combustion locomotives use an internal combustion engine , connected to the driving wheels by a transmission. They typically keep the engine running at a near-constant speed whether the locomotive is stationary or moving. Internal combustion locomotives are categorised by their fuel type and sub-categorised by their transmission type. The first internal combustion rail vehicle

12750-631: Was Puffing Billy , built 1813–14 by engineer William Hedley for the Wylam Colliery near Newcastle upon Tyne . This locomotive is the oldest preserved, and is on static display in the Science Museum, London. George Stephenson built Locomotion No. 1 for the Stockton & Darlington Railway in the north-east of England, which was the first public steam railway in the world. In 1829, his son Robert built The Rocket in Newcastle upon Tyne. Rocket

12875-491: Was Puffing Billy , built 1813–14 by engineer William Hedley . It was intended to work on the Wylam Colliery near Newcastle upon Tyne. This locomotive is the oldest preserved, and is on static display at the Science Museum, London . George Stephenson , a former miner working as an engine-wright at Killingworth Colliery , developed up to sixteen Killingworth locomotives , including Blücher in 1814, another in 1815, and

13000-491: Was a kerosene -powered draisine built by Gottlieb Daimler in 1887, but this was not technically a locomotive as it carried a payload. The earliest gasoline locomotive in the western United States was built by the Best Manufacturing Company in 1891 for San Jose and Alum Rock Railroad . It was only a limited success and was returned to Best in 1892. The first commercially successful petrol locomotive in

13125-571: Was a major engineering feature of the line; possessing a length of 10,216 meters, it was the longest railway tunnel in Austria, and would remain so for over one hundred years. On 21 September 1884, it was opened as a single-track tunnel, and rapidly became saturated by heavy traffic. Accordingly, the second parallel track was installed and operational by 15 July 1885. The tunnel starts at near the railway station serving St. Anton am Arlberg and ends in Langen am Arlberg . Early on, operations became troubled by

13250-575: Was built in 1834 by Cherepanovs , however, it suffered from the lack of coal in the area and was replaced with horse traction after all the woods nearby had been cut down. The first Russian Tsarskoye Selo steam railway started in 1837 with locomotives purchased from Robert Stephenson and Company . In 1837, the first steam railway started in Austria on the Emperor Ferdinand Northern Railway between Vienna-Floridsdorf and Deutsch-Wagram . The oldest continually working steam engine in

13375-752: Was constructed for the Coalbrookdale ironworks in Shropshire in England though no record of it working there has survived. On 21 February 1804, the first recorded steam-hauled railway journey took place as another of Trevithick's locomotives hauled a train from the Penydarren ironworks, in Merthyr Tydfil , to Abercynon in South Wales. Accompanied by Andrew Vivian , it ran with mixed success. The design incorporated

13500-574: Was constructed for the Coalbrookdale ironworks in Shropshire in the United Kingdom though no record of it working there has survived. On 21 February 1804, the first recorded steam-hauled railway journey took place as another of Trevithick's locomotives hauled a train along the 4 ft 4 in ( 1,321 mm )-wide tramway from the Pen-y-darren ironworks, near Merthyr Tydfil , to Abercynon in South Wales. Accompanied by Andrew Vivian , it ran with mixed success. The design incorporated

13625-662: Was demonstrated in Val-d'Or , Quebec . In 2007 the educational mini-hydrail in Kaohsiung , Taiwan went into service. The Railpower GG20B finally is another example of a fuel cell–electric locomotive. There are many different types of hybrid or dual-mode locomotives using two or more types of motive power. The most common hybrids are electro-diesel locomotives powered either from an electricity supply or else by an onboard diesel engine . These are used to provide continuous journeys along routes that are only partly electrified. Examples include

13750-467: Was designed by Charles Brown , then working for Oerlikon , Zürich. In 1891, Brown had demonstrated long-distance power transmission, using three-phase AC , between a hydro-electric plant at Lauffen am Neckar and Frankfurt am Main West, a distance of 280 km. Using experience he had gained while working for Jean Heilmann on steam–electric locomotive designs, Brown observed that three-phase motors had

13875-411: Was dictated by the maximum axle loading of the railroad in question. A builder would typically add axles until the maximum weight on any one axle was acceptable to the railroad's maximum axle loading. A locomotive with a wheel arrangement of two lead axles, two drive axles, and one trailing axle was a high-speed machine. Two lead axles were necessary to have good tracking at high speeds. Two drive axles had

14000-480: Was entered in and won the Rainhill Trials . This success led to the company emerging as the pre-eminent builder of steam locomotives used on railways in the UK, US and much of Europe. The Liverpool and Manchester Railway opened a year later making exclusive use of steam power for passenger and goods trains . Before the arrival of British imports, some domestic steam locomotive prototypes were built and tested in

14125-538: Was entered into, and won, the Rainhill Trials . This success led to the company emerging as the pre-eminent early builder of steam locomotives used on railways in the UK, US and much of Europe. The Liverpool & Manchester Railway , built by Stephenson, opened a year later making exclusive use of steam power for passenger and goods trains . The steam locomotive remained by far the most common type of locomotive until after World War II . Steam locomotives are less efficient than modern diesel and electric locomotives, and

14250-679: Was named The Elephant , which on 5 May 1835 hauled a train on the first line in Belgium, linking Mechelen and Brussels. In Germany, the first working steam locomotive was a rack-and-pinion engine, similar to the Salamanca , designed by the British locomotive pioneer John Blenkinsop . Built in June 1816 by Johann Friedrich Krigar in the Royal Berlin Iron Foundry ( Königliche Eisengießerei zu Berlin),

14375-557: Was never officially proven. In the United States, larger loading gauges allowed the development of very large, heavy locomotives such as the Union Pacific Big Boy , which weighs 540 long tons (550  t ; 600 short tons ) and has a tractive effort of 135,375 pounds-force (602,180 newtons). Beginning in the early 1900s, steam locomotives were gradually superseded by electric and diesel locomotives , with railways fully converting to electric and diesel power beginning in

14500-524: Was opened. The arid nature of south Australia posed distinctive challenges to their early steam locomotion network. The high concentration of magnesium chloride in the well water ( bore water ) used in locomotive boilers on the Trans-Australian Railway caused serious and expensive maintenance problems. At no point along its route does the line cross a permanent freshwater watercourse, so bore water had to be relied on. No inexpensive treatment for

14625-426: Was presented by Werner von Siemens at Berlin in 1879. The locomotive was driven by a 2.2 kW, series-wound motor, and the train, consisting of the locomotive and three cars, reached a speed of 13 km/h. During four months, the train carried 90,000 passengers on a 300-metre-long (984 feet) circular track. The electricity (150 V DC) was supplied through a third insulated rail between the tracks. A contact roller

14750-419: Was proposed by William Reynolds around 1787. An early working model of a steam rail locomotive was designed and constructed by steamboat pioneer John Fitch in the US during 1794. Some sources claim Fitch's model was operable already by the 1780s and that he demonstrated his locomotive to George Washington . His steam locomotive used interior bladed wheels guided by rails or tracks. The model still exists at

14875-512: Was soon established. In 1830, the Baltimore and Ohio Railroad 's Tom Thumb , designed by Peter Cooper , was the first commercial US-built locomotive to run in America; it was intended as a demonstration of the potential of steam traction rather than as a revenue-earning locomotive. The DeWitt Clinton , built in 1831 for the Mohawk and Hudson Railroad , was a notable early locomotive. As of 2021 ,

15000-403: Was supplied at stopping places and locomotive depots from a dedicated water tower connected to water cranes or gantries. In the UK, the US and France, water troughs ( track pans in the US) were provided on some main lines to allow locomotives to replenish their water supply without stopping, from rainwater or snowmelt that filled the trough due to inclement weather. This was achieved by using

15125-924: Was tested on the Edinburgh and Glasgow Railway in September of the following year, but the limited power from batteries prevented its general use. Another example was at the Kennecott Copper Mine , Latouche, Alaska , where in 1917 the underground haulage ways were widened to enable working by two battery locomotives of 4 + 1 ⁄ 2 tons. In 1928, Kennecott Copper ordered four 700-series electric locomotives with on-board batteries. These locomotives weighed 85 tons and operated on 750-volt overhead trolley wire with considerable further range whilst running on batteries. The locomotives provided several decades of service using Nickel–iron battery (Edison) technology. The batteries were replaced with lead-acid batteries , and

15250-633: Was the first in the world in regular service powered from an overhead line. Five years later, in the U.S. electric trolleys were pioneered in 1888 on the Richmond Union Passenger Railway , using equipment designed by Frank J. Sprague . The first electrically worked underground line was the City & South London Railway , prompted by a clause in its enabling act prohibiting use of steam power. It opened in 1890, using electric locomotives built by Mather & Platt . Electricity quickly became

15375-404: Was to use built-up bar frames, with the smokebox saddle/cylinder structure and drag beam integrated therein. In the 1920s, with the introduction of "superpower", the cast-steel locomotive bed became the norm, incorporating frames, spring hangers, motion brackets, smokebox saddle and cylinder blocks into a single complex, sturdy but heavy casting. A SNCF design study using welded tubular frames gave

15500-534: Was used on several railways in Northern Italy and became known as "the Italian system". Kandó was invited in 1905 to undertake the management of Società Italiana Westinghouse and led the development of several Italian electric locomotives. A battery–electric locomotive (or battery locomotive) is an electric locomotive powered by onboard batteries ; a kind of battery electric vehicle . Such locomotives are used where

15625-566: Was used to collect the electricity. The world's first electric tram line opened in Lichterfelde near Berlin, Germany, in 1881. It was built by Werner von Siemens (see Gross-Lichterfelde Tramway and Berlin Straßenbahn ). The Volk's Electric Railway opened in 1883 in Brighton, and is the oldest surviving electric railway. Also in 1883, Mödling and Hinterbrühl Tram opened near Vienna in Austria. It

#695304